From b250b233ec136cfe2655c4de8d18468cd1959083 Mon Sep 17 00:00:00 2001
From: Christian Poessinger <christian@poessinger.com>
Date: Sat, 4 Apr 2020 11:30:10 +0200
Subject: pppoe: T1318: move Jinja2 templates to data/templates folder

This makes the actual code which generates the configs much more human
readable.
---
 data/templates/pppoe/ip-pre-up.script.tmpl | 19 ++++++++
 data/templates/pppoe/ipv6-up.script.tmpl   | 41 ++++++++++++++++++
 data/templates/pppoe/peer.tmpl             | 69 ++++++++++++++++++++++++++++++
 3 files changed, 129 insertions(+)
 create mode 100644 data/templates/pppoe/ip-pre-up.script.tmpl
 create mode 100644 data/templates/pppoe/ipv6-up.script.tmpl
 create mode 100644 data/templates/pppoe/peer.tmpl

(limited to 'data/templates/pppoe')

diff --git a/data/templates/pppoe/ip-pre-up.script.tmpl b/data/templates/pppoe/ip-pre-up.script.tmpl
new file mode 100644
index 000000000..f72781e41
--- /dev/null
+++ b/data/templates/pppoe/ip-pre-up.script.tmpl
@@ -0,0 +1,19 @@
+#!/bin/sh
+
+# As PPPoE is an "on demand" interface we need to re-configure it when it
+# becomes up
+
+if [ "$6" != "{{ intf }}" ]; then
+    exit
+fi
+
+# add some info to syslog
+DIALER_PID=$(cat /var/run/{{ intf }}.pid)
+logger -t pppd[$DIALER_PID] "executing $0"
+
+echo "{{ description }}" > /sys/class/net/{{ intf }}/ifalias
+
+{% if vrf -%}
+logger -t pppd[$DIALER_PID] "configuring dialer interface $6 for VRF {{ vrf }}"
+ip link set dev {{ intf }} master {{ vrf }}
+{% endif %}
diff --git a/data/templates/pppoe/ipv6-up.script.tmpl b/data/templates/pppoe/ipv6-up.script.tmpl
new file mode 100644
index 000000000..037db66db
--- /dev/null
+++ b/data/templates/pppoe/ipv6-up.script.tmpl
@@ -0,0 +1,41 @@
+#!/bin/sh
+
+# As PPPoE is an "on demand" interface we need to re-configure it when it
+# becomes up
+
+if [ "$6" != "{{ intf }}" ]; then
+    exit
+fi
+
+{% if ipv6_autoconf -%}
+# add some info to syslog
+DIALER_PID=$(cat /var/run/{{ intf }}.pid)
+logger -t pppd[$DIALER_PID] "executing $0"
+logger -t pppd[$DIALER_PID] "configuring interface {{ intf }} via $2"
+
+# Configure interface-specific Host/Router behaviour.
+# Note: It is recommended to have the same setting on all interfaces; mixed
+# router/host scenarios are rather uncommon. Possible values are:
+#
+# 0  Forwarding disabled
+# 1  Forwarding enabled
+#
+echo 1 > /proc/sys/net/ipv6/conf/{{ intf }}/forwarding
+
+# Accept Router Advertisements; autoconfigure using them.
+#
+# It also determines whether or not to transmit Router
+# Solicitations. If and only if the functional setting is to
+# accept Router Advertisements, Router Solicitations will be
+# transmitted. Possible values are:
+#
+# 0  Do not accept Router Advertisements.
+# 1  Accept Router Advertisements if forwarding is disabled.
+# 2  Overrule forwarding behaviour. Accept Router Advertisements
+#    even if forwarding is enabled.
+#
+echo 2 > /proc/sys/net/ipv6/conf/{{ intf }}/accept_ra
+
+# Autoconfigure addresses using Prefix Information in Router Advertisements.
+echo 1 > /proc/sys/net/ipv6/conf/{{ intf }}/autoconfigure
+{% endif %}
diff --git a/data/templates/pppoe/peer.tmpl b/data/templates/pppoe/peer.tmpl
new file mode 100644
index 000000000..029361101
--- /dev/null
+++ b/data/templates/pppoe/peer.tmpl
@@ -0,0 +1,69 @@
+### Autogenerated by interfaces-pppoe.py ###
+
+{% if description %}
+# {{ description }}
+{% endif %}
+
+# Require peer to provide the local IP address if it is not
+# specified explicitly in the config file.
+noipdefault
+
+# Don't show the password in logfiles:
+hide-password
+
+# Standard Link Control Protocol (LCP) parameters:
+lcp-echo-interval 20
+lcp-echo-failure 3
+
+# RFC 2516, paragraph 7 mandates that the following options MUST NOT be
+# requested and MUST be rejected if requested by the peer:
+# Address-and-Control-Field-Compression (ACFC)
+noaccomp
+
+# Asynchronous-Control-Character-Map (ACCM)
+default-asyncmap
+
+# Override any connect script that may have been set in /etc/ppp/options.
+connect /bin/true
+
+# Don't try to authenticate the remote node
+noauth
+
+# Don't try to proxy ARP for the remote endpoint. User can set proxy
+# arp entries up manually if they wish.  More importantly, having
+# the "proxyarp" parameter set disables the "defaultroute" option.
+noproxyarp
+
+# Unlimited connection attempts
+maxfail 0
+
+plugin rp-pppoe.so
+{{ source_interface }}
+persist
+ifname {{ intf }}
+ipparam {{ intf }}
+debug
+logfile {{ logfile }}
+{% if 'auto' in default_route -%}
+defaultroute
+{% elif 'force' in default_route -%}
+defaultroute
+replacedefaultroute
+{% endif %}
+mtu {{ mtu }}
+mru {{ mtu }}
+user "{{ auth_username }}"
+password "{{ auth_password }}"
+{% if name_server -%}
+usepeerdns
+{% endif %}
+{% if ipv6_enable -%}
++ipv6
+ipv6cp-use-ipaddr
+{% endif %}
+{% if service_name -%}
+rp_pppoe_service "{{ service_name }}"
+{% endif %}
+{% if on_demand %}
+demand
+{% endif %}
-- 
cgit v1.2.3