Point to Point over Ethernet (PPPoE) Server 900 Enable SNMP enable SNMP master agent mode Access concentrator name ^[a-zA-Z0-9]{1,100} access-concentrator name limited to alphanumerical characters only (max. 100) Authentication for remote access PPPoE Server Local user authentication for PPPoE server User name for authentication Option to disable a PPPoE Server user Password for authentication Static client IP address Upload/Download speed limits Upload bandwidth limit in kbits/sec Download bandwidth limit in kbits/sec Authentication mode for PPPoE Server local Use local username/password configuration radius Use a RADIUS server to autenticate users ^(local|radius) local radius IP address of RADIUS server ipv4 IP address of RADIUS server Key for accessing the specified server Maximum number of simultaneous requests to server (default: unlimited) If server does not responds mark it as unavailable for this amount of time in seconds RADIUS settings Timeout to wait response from server (seconds) Timeout to wait reply for Interim-Update packets. (default 3 seconds) Maximum number of tries to send Access-Request/Accounting-Request queries Value to send to RADIUS server in NAS-Identifier attribute and to be matched in DM/CoA requests. Value to send to RADIUS server in NAS-IP-Address attribute and to be matched in DM/CoA requests. Also DM/CoA server will bind to that address. IPv4 address and port to bind Dynamic Authorization Extension server (DM/CoA) IP address for Dynamic Authorization Extension server (DM/CoA) Port for Dynamic Authorization Extension server (DM/CoA) Secret for Dynamic Authorization Extension server (DM/CoA) Upload/Download speed limits Specifies which radius attribute contains rate information. (default is Filter-Id) Specifies the vendor dictionary. (dictionary needs to be in /usr/share/accel-ppp/radius) Enables Bandwidth shaping via RADIUS Pool of client IP addresses (must be within a /24) First IP address in the pool Last IP address in the pool Client IP subnet (CIDR notation) Not a valid CIDR formatted prefix Pool of client IPv6 addresses Format: ipv6prefix/mask,prefix_len (e.g.: fc00:0:1::/48,64 - divides prefix into /64 subnets for clients) Format: ipv6prefix/mask,prefix_len (delegate to clients through DHCPv6 prefix delegation - rfc3633) IPv4 Domain Name Service (DNS) server Primary DNS server ipv4 IPv4 address Secondary DNS server ipv4 IPv4 address IPv6 Domain Name Service (DNS) server ipv6 IPv6 address Primary DNS server ipv6 IPv6 address Secondary DNS server ipv6 IPv6 address Tertiary DNS server interface(s) to listen on VLAN monitor for the automatic creation of vlans (user per vlan) VLAN ID needs to be between 1 and 4096 VLAN monitor for the automatic creation of vlans (user per vlan) (409[0-6]|40[0-8][0-9]|[1-3][0-9]{3}|[1-9][0-9]{0,2})-(409[0-6]|40[0-8][0-9]|[1-3][0-9]{3}|[1-9][0-9]{0,2}) local gateway address Maximum Transmission Unit (MTU) - default 1492 Limits the connection rate from a single source Acceptable rate of connections (e.g. 1/min, 60/sec) ^[0-9]+\/(min|sec)$ illegal value Burst count Timeout in seconds Service name ^[a-zA-Z0-9\-]{1,100} servicename can contain aplhanumerical characters and dashes only (max. 100) Windows Internet Name Service (WINS) server settings Primary WINS server Secondary WINS server Advanced protocol options Minimum acceptable MTU (68-65535) Preferred MRU (68-65535) CCP negotiation (default disabled) Specifies MPPE negotiation preference. (default prefer mppe) Ask client for MPPE, if it rejects then drop the connection Ask client for MPPE, if it rejects do not fail Deny MPPE LCP echo-requests/sec Maximum number of Echo-Requests may be sent without valid reply Timeout in seconds to wait for any peer activity. If this option specified it turns on adaptive lcp echo functionality and "lcp-echo-failure" is not used. IPv4 (IPCP) negotiation algorithm ^(deny|allow|prefer|require) invalid value deny Do not negotiate IPv4 allow Negotiate IPv4 only if client requests prefer Ask client for IPv4 negotiation, do not fail if it rejects require Require IPv4 negotiation IPv6 (IPCP6) negotiation algorithm ^(deny|allow|prefer|require) invalid value deny Do not negotiate IPv6 allow Negotiate IPv6 only if client requests prefer Ask client for IPv6 negotiation, do not fail if it rejects require Require IPv6 negotiation Fixed or random interface identifier for IPv6 random Random interface identifier for IPv6 x:x:x:x specify interface identifier for IPv6 Peer interface identifier for IPv6 x:x:x:x Interface identifier for IPv6 random Use a random interface identifier for IPv6 ipv4 Calculate interface identifier from IPv4 address, for example 192:168:0:1 calling-sid Calculate interface identifier from calling-station-id Accept peer interface identifier