1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
|
### Autogenerated by interfaces-macsec.py ###
# see full documentation:
# https://w1.fi/cgit/hostap/plain/wpa_supplicant/wpa_supplicant.conf
# For UNIX domain sockets (default on Linux and BSD): This is a directory that
# will be created for UNIX domain sockets for listening to requests from
# external programs (CLI/GUI, etc.) for status information and configuration.
# The socket file will be named based on the interface name, so multiple
# wpa_supplicant processes can be run at the same time if more than one
# interface is used.
# /var/run/wpa_supplicant is the recommended directory for sockets and by
# default, wpa_cli will use it when trying to connect with wpa_supplicant.
ctrl_interface=/run/wpa_supplicant
# Note: When using MACsec, eapol_version shall be set to 3, which is
# defined in IEEE Std 802.1X-2010.
eapol_version=3
# No need to scan for access points in MACsec mode
ap_scan=0
# EAP fast re-authentication
fast_reauth=1
network={
key_mgmt=NONE
# Note: When using wired authentication (including MACsec drivers),
# eapol_flags must be set to 0 for the authentication to be completed
# successfully.
eapol_flags=0
# macsec_policy: IEEE 802.1X/MACsec options
# This determines how sessions are secured with MACsec (only for MACsec
# drivers).
# 0: MACsec not in use (default)
# 1: MACsec enabled - Should secure, accept key server's advice to
# determine whether to use a secure session or not.
macsec_policy=1
# macsec_integ_only: IEEE 802.1X/MACsec transmit mode
# This setting applies only when MACsec is in use, i.e.,
# - macsec_policy is enabled
# - the key server has decided to enable MACsec
# 0: Encrypt traffic (default)
# 1: Integrity only
macsec_integ_only={{ '0' if security.encrypt is vyos_defined else '1' }}
{% if security.encrypt is vyos_defined %}
# mka_cak, mka_ckn, and mka_priority: IEEE 802.1X/MACsec pre-shared key mode
# This allows to configure MACsec with a pre-shared key using a (CAK,CKN) pair.
# In this mode, instances of wpa_supplicant can act as MACsec peers. The peer
# with lower priority will become the key server and start distributing SAKs.
# mka_cak (CAK = Secure Connectivity Association Key) takes a 16-byte (128-bit)
# hex-string (32 hex-digits) or a 32-byte (256-bit) hex-string (64 hex-digits)
# mka_ckn (CKN = CAK Name) takes a 1..32-bytes (8..256 bit) hex-string
# (2..64 hex-digits)
mka_cak={{ security.mka.cak }}
mka_ckn={{ security.mka.ckn }}
# mka_priority (Priority of MKA Actor) is in 0..255 range with 255 being
# default priority
mka_priority={{ security.mka.priority }}
{% endif %}
{% if security.replay_window is vyos_defined %}
# macsec_replay_protect: IEEE 802.1X/MACsec replay protection
# This setting applies only when MACsec is in use, i.e.,
# - macsec_policy is enabled
# - the key server has decided to enable MACsec
# 0: Replay protection disabled (default)
# 1: Replay protection enabled
macsec_replay_protect=1
# macsec_replay_window: IEEE 802.1X/MACsec replay protection window
# This determines a window in which replay is tolerated, to allow receipt
# of frames that have been misordered by the network.
# This setting applies only when MACsec replay protection active, i.e.,
# - macsec_replay_protect is enabled
# - the key server has decided to enable MACsec
# 0: No replay window, strict check (default)
# 1..2^32-1: number of packets that could be misordered
macsec_replay_window={{ security.replay_window }}
{% endif %}
}
|
