| Age | Commit message (Collapse) | Author |
|---|
|
net: add render_route comment to document why we added || true to route
statements
DataSourceConfigDrive: Only convert network_json to network_config when
caller reads network_config attr. Cache the conversion.
|
|
|
|
Changing this interface to allow for easy change later.
The thing that this will enable is:
a.) maas datasource to look at the system config and see if it
is configured with the same consumer_key
b.) datasource config could allow setting a variable that it
would look at.
|
|
|
|
add tests to show this functional.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Wesley's loader returned network state, so that got me updating
it, and i implemented as such. Then realized that actually
ipconfig (klibc) has no support for ipv6. So even though
i painfully generalized that, its pointless. next commit will
drop it.
|
|
|
|
|
|
|
|
Enabled NICS even in failure case.
Used util.del_dir() instead of shutil.rmtree.
|
|
|
|
|
|
Tested now with the generated fallback config in an lxc container.
Had to change to return a config rather than a network state.
Also this makes nocloud look in nocloud-net's seed dir.
This way it will read the seed and clame the datasource but
not do anything other than apply networking and the init_modules early.
It is a change in behavior of the time that boothooks woudl run to do
this. May need to change that back.
|
|
|
|
there is no data source that has a populated network_config()
so at this point this doesn't do anything.
|
|
|
|
|
|
on interfaces with characters between their numbers
|
|
I plan to re-use these methods later. They stand alone even if they
dont end up getting used, though.
|
|
'version' keys
|
|
- Removed systemd .link file generation, as it is not needed right now
- Changed return of generate_fallback_config to be just ns dict
- In distros.debian don't attempt to write .link file
|
|
|
|
configuration to be run if there is no network configuration provided by the
datasource.
NOTE: the code added here will not behave correctly if a net datasource has
network configuration. this code is temporary and should be reverted once
support for network configuration for net datasources after retrieving
config is in place.
based on: http://paste.ubuntu.com/15443576/
With this in place cloud-init properly chooses a fallback interface, configures
it and brings it online
|
|
not to attempt renaming the network interface to the default interface. Default
interface is controleld by net.DEFAULT_PRIMARY_INTERFACE and is currently set
to eth0 for legacy reasons. By default cloud-init will not attempt to rename
the device as this does not work in some situtations depending on the backing
driver of the device.
|
|
|
|
|
|
try/except blocks because there are sometimes read errors on the files and this
should not cause a stacktrace
|
|
|
|
|
|
|
|
|
|
distros base, and apply_fallback_network to distros to call
_write_network_fallback. Note that since _write_network_fallback is only
implemented for debian and ubuntu a check is needed to ensure that it does not
break behaviour for other distros.
Added function to disable .cfg files to util, since it may be useful elsewhere
|
|
This adds a check in cloud-init to see if the existing (cached)
datasource is still valid. It relies on support from the Datasource
to implement 'check_instance_id'. That method should quickly determine
(if possible) if the instance id found in the datasource is still valid.
This means that we can still notice new instance ids without
depending on a network datasource on every boot.
I've also implemented check_instance_id for the superclass and for
3 classes:
DataSourceAzure (check dmi data)
DataSourceOpenstack (check dmi data)
DataSourceNocloud (check the seeded data or kernel command line)
LP: #1553815
|
|
on in the event that no network configuration was provided to cloud-init
- Devices in /sys/class/net aside from loopback devices are scanned
- Each device is tested to determine if it has a carrier using
/sys/class/net/DEV/carrier, devices which do are preferred as they are most
likely connected to the outside world
- Devices which do not have a carrier but which might still be connected due
to being in a dormant or down state are used as fallbacks in case no
devices are found which have a carrier
- A network state dictionary is generated to be passed to
render_network_state to write ENI
- A systemd link file is generated that will rename the chosen device to eth0
|
|
- Modified the code to look for customization specification file in
/var/run/vmware-imc/ directory instead of /tmp
- Fixed the 'seed file' issue. There was a regression in DataSourceOVF.py
file. Fixed it.
|
|
|
|
|
|
lp:cloud-initramfs-tools/dyn-netconf/scripts/init-bottom/cloud-initramfs-dyn-netconf
|
|
broadcast, netmask, gateway and hostname if present
|
|
|
|
kernel's cmdline during network configuration parsing.
- Search for .conf files in /run with names starting with 'net', as these are
created during early boot if the ip parameter is present
- If any are present and valid they are merged with network configuration
from the current data source
- If the devices affected by the 'ip' parameter are already present in
network configuration, then a subnet entry will be added to the device's
configuration unless an identical entry is already present
- If any of the devices affected are not present then a mostly blank
configuration will be generated for the device and the appropriate subnet
specified
|
|
Added code to customize timezone.
Added few utility functions to send events to the VMware hypervisor.
Re-factored the code little bit.
Added code to send SUCCESS event when customization succeeds.
Added code to send FAILED event if any error occurs during customization.
|
|
parsing the command line parameters returned a dictionary
but _merge_new_seed was expecting a string to be yaml loaded.
Change is to make _merge_new_seed take either string or dict.
|
|
from any ip= parameters passed on the kernel cmdline are merged into network
state
|
