arrange services and protocols

1 files changed, 157 insertions, 0 deletions

diff --git a/docs/configuration/protocols/mpls.rst b/docs/configuration/protocols/mpls.rst
new file mode 100644
index 00000000..82e99a17
--- /dev/null
+++ b/docs/configuration/protocols/mpls.rst
@@ -0,0 +1,157 @@
+.. _mpls:
+
+####################################
+MPLS (Multiprotocol Label Switching)
+####################################
+
+:abbr:`MPLS (Multi-Protocol Label Switching)` is a packet forwarding paradigm
+which differs from regular IP forwarding. Instead of IP addresses being used to
+make the decision on finding the exit interface, a router will instead use an
+exact match on a 32 bit/4 byte header called the MPLS label. This label is
+inserted between the ethernet (layer 2) header and the IP (layer 3) header.
+One can statically or dynamically assign label allocations, but we will focus
+on dynamic allocation of labels using some sort of label distribution protocol
+(such as the aptly named Label Distribution Protocol / LDP, Resource Reservation
+Protocol / RSVP, or Segment Routing through OSPF/ISIS). These protocols allow
+for the creation of a unidirectional/unicast path called a labeled switched
+path (initialized as LSP) throughout the network that operates very much like
+a tunnel through the network. An easy way of thinking about how an MPLS LSP
+actually forwards traffic throughout a network is to think of a GRE tunnel.
+They are not the same in how they operate, but they are the same in how they
+handle the tunneled packet. It would be good to think of MPLS as a tunneling
+technology that can be used to transport many different types of packets, to
+aid in traffic engineering by allowing one to specify paths throughout the
+network (using RSVP or SR), and to generally allow for easier intra/inter
+network transport of data packets.
+
+For more information on how MPLS label switching works, please go visit
+`Wikipedia (MPLS)`_.
+
+.. note:: MPLS support in VyOS is not finished yet, and therefore its
+   functionality is limited. Currently there is no support for MPLS enabled VPN
+   services such as L3VPNs, L2VPNs, and mVPNs. RSVP support is also not present
+   as the underlying routing stack (FRR) does not implement it. Currently VyOS
+   can be configured as a label switched router (MPLS P router), in both
+   penultimate and ultimate hop popping operations.
+
+Label Distribution Protocol
+===========================
+
+The :abbr:`MPLS (Multi-Protocol Label Switching)` architecture does not assume
+a single protocol to create MPLS paths. VyOS supports the Label Distribution
+Protocol (LDP) as implemented by FRR, based on :rfc:`5036`.
+
+:abbr:`LDP (Label Distribution Protocol)` is a TCP based MPLS signaling protocol
+that distributes labels creating MPLS label switched paths in a dynamic manner.
+LDP is not a routing protocol, as it relies on other routing protocols for
+forwarding decisions. LDP cannot bootstrap itself, and therefore relies on said
+routing protocols for communication with other routers that use LDP.
+
+In order to allow for LDP on the local router to exchange label advertisements
+with other routers, a TCP session will be established between automatically
+discovered and statically assigned routers. LDP will try to establish a TCP
+session to the **transport address** of other routers. Therefore for LDP to
+function properly please make sure the transport address is shown in the
+routing table and reachable to traffic at all times.
+
+It is highly recommended to use the same address for both the LDP router-id and
+the discovery transport address, but for VyOS MPLS LDP to work both parameters
+must be explicitly set in the configuration.
+
+Configuration Options
+=====================
+
+.. cfgcmd:: set protocols mpls ldp interface <interface>
+
+  Use this command to enable LDP, and enable MPLS processing on the interface you
+  define.
+
+.. cfgcmd:: set protocols mpls ldp router-id <address>
+
+  Use this command to configure the IP address used as the LDP router-id of the
+  local device.
+
+.. cfgcmd:: set protocols mpls ldp discovery transport-ipv4-address <IPv4 address>
+.. cfgcmd:: set protocols mpls ldp discovery transport-ipv6-address <IPv6 address>
+
+  Use this command to set the IPv4 or IPv6 transport-address used by LDP.
+
+.. cfgcmd:: set protocols mpls ldp neighbor <IPv4 address> password <password>
+
+  Use this command to configure authentication for LDP peers. Set the
+  IP address of the LDP peer and a password that should be shared in
+  order to become neighbors.
+
+.. cfgcmd:: set protocols mpls ldp discovery hello-interval <seconds>
+.. cfgcmd:: set protocols mpls ldp discovery hello-holdtime <seconds>
+
+  Use this command if you would like to set the discovery hello and hold time
+  parameters.
+
+.. cfgcmd:: set protocols mpls ldp discovery session-ipv4-holdtime <seconds>
+.. cfgcmd:: set protocols mpls ldp discovery session-ipv6-holdtime <seconds>
+
+  Use this command if you would like to set the TCP session hold time intervals.
+
+.. cfgcmd:: set protocols mpls ldp export ipv4 explicit-null
+.. cfgcmd:: set protocols mpls ldp export ipv6 explicit-null
+
+  Use this command if you would like for the router to advertise FECs with a label
+  of 0 for explicit null operations.
+
+
+Sample configuration to setup LDP on VyOS
+-----------------------------------------
+
+.. code-block:: none
+
+  set protocols ospf area 0 network '192.168.255.252/32'                      <--- Routing for loopback
+  set protocols ospf area 0 network '192.168.0.5/32'                          <--- Routing for an interface connecting to the network
+  set protocols ospf parameters router-id '192.168.255.252'                   <--- Router ID setting for OSPF
+  set protocols mpls ldp discovery transport-ipv4-address '192.168.255.252'   <--- Transport address for LDP for TCP sessions to connect to
+  set protocols mpls ldp interface 'eth1'                                     <--- Enable MPLS and LDP for an interface connecting to network
+  set protocols mpls ldp interface 'lo'                                       <--- Enable MPLS and LDP on loopback for future services connectivity
+  set protocols mpls ldp router-id '192.168.255.252'                          <--- Router ID setting for LDP
+  set interfaces ethernet eth1 address '192.168.0.5/31'                       <--- Interface IP for connecting to network
+  set interfaces loopback lo address '192.168.255.252/32'                     <--- Interface loopback IP for router ID and other uses
+
+
+Operational Mode Commands
+=========================
+
+When LDP is working, you will be able to see label information in the outcome
+of ``show ip route``. Besides that information, there are also specific *show*
+commands for LDP:
+
+Show
+----
+
+.. opcmd:: show mpls ldp binding
+
+  Use this command to see the Label Information Base.
+
+.. opcmd:: show mpls ldp discovery
+
+  Use this command to see discovery hello information
+
+.. opcmd:: show mpls ldp interface
+
+  Use this command to see LDP interface information
+
+.. opcmd:: show mpls ldp neighbor
+
+  Use this command to see LDP neighbor information
+
+.. opcmd:: show mpls ldp neighbor detail
+
+  Use this command to see detailed LDP neighbor information
+
+Reset
+-----
+
+.. opcmd:: reset mpls ldp neighbor <IPv4 or IPv6 address>
+
+  Use this command to reset an LDP neighbor/TCP session that is established
+
+
+.. _`Wikipedia (MPLS)`: https://en.wikipedia.org/wiki/Multiprotocol_Label_Switching