Revert "Add incremental RST-to-MyST swap mechanism (circinus) (#1867)" (#1893)

This reverts commit 5eb383a10ec92c65eed525bc174785a6852e997f.

6 files changed, 0 insertions, 439 deletions

diff --git a/docs/troubleshooting/md-connectivity.md b/docs/troubleshooting/md-connectivity.md
deleted file mode 100644
index a3c95d8c..00000000
--- a/docs/troubleshooting/md-connectivity.md
+++ /dev/null
@@ -1,147 +0,0 @@
-# Connectivity Tests
-
-## Basic Connectivity Tests
-
-Verifying connectivity can be done with the familiar ping and traceroute
-commands. The options for each are shown (the options for each command were
-displayed using the built-in help as described in the {ref}`cli`
-section and are omitted from the output here):
-
-```{opcmd} ping \<destination\>
-
-Send ICMP echo requests to destination host. There are multiple options to
-ping, including VRF support.
-
-:::{code-block} none
-vyos@vyos:~$ ping 10.1.1.1
-Possible completions:
-<Enter>       Execute the current command
-adaptive      Ping options
-allow-broadcast
-audible
-bypass-route
-count
-deadline
-do-not-fragment
-flood
-interface
-interval
-mark
-no-loopback
-numeric
-pattern
-quiet
-record-route
-size
-timestamp
-tos
-ttl
-verbose
-vrf
-:::
-```
-
-```{opcmd} traceroute \<destination\>
-
-Trace path to target.
-
-:::{code-block} none
-vyos@vyos:~$ traceroute
-Possible completions:
-<hostname>    Track network path to specified node
-<x.x.x.x>
-<h:h:h:h:h:h:h:h>
-ipv4          Track network path to <hostname|IPv4 address>
-ipv6          Track network path to <hostname|IPv6 address>
-:::
-```
-
-
-## Advanced Connectivity Tests
-
-```{opcmd} monitor traceroute \<destination\>
-
-However, another helper is available which combines ping and traceroute
-into a single tool. An example of its output is shown:
-
-:::{code-block} none
-vyos@vyos:~$ mtr 10.62.212.12
-
-                           My traceroute  [v0.85]
-vyos (0.0.0.0)
-Keys:  Help   Display mode   Restart statistics   Order of fields   quit
-                                  Packets               Pings
-Host                            Loss%   Snt   Last   Avg  Best  Wrst StDev
-1. 10.11.110.4                   0.0%    34    0.5   0.5   0.4   0.8   0.1
-2. 10.62.255.184                 0.0%    34    1.1   1.0   0.9   1.4   0.1
-3. 10.62.255.71                  0.0%    34    1.4   1.4   1.3   2.0   0.1
-4. 10.62.212.12                  0.0%    34    1.6   1.6   1.6   1.7   0.0
-:::
-
-:::{note}
-The output consumes the screen and will replace your command
-prompt.
-:::
-
-Several options are available for changing the display output. Press h to
-invoke the built in help system. To quit, just press q and you'll be
-returned to the VyOS command prompt.
-```
-
-
-## IPv6 Topology Discovery
-
-IPv6 uses different techniques to discover its Neighbors/topology.
-
-### Router Discovery
-
-```{opcmd} force ipv6-rd interface \<interface\> [address \<ipv6-address\>]
-
-Discover routers via eth0.
-
-Example:
-
-:::{code-block} none
-vyos@vyos:~$ force ipv6-rd interface eth0
-Soliciting ff02::2 (ff02::2) on eth0...
-
-Hop limit                 :           60 (      0x3c)
-Stateful address conf.    :           No
-Stateful other conf.      :           No
-Mobile home agent         :           No
-Router preference         :         high
-Neighbor discovery proxy  :           No
-Router lifetime           :         1800 (0x00000708) seconds
-Reachable time            :  unspecified (0x00000000)
-Retransmit time           :  unspecified (0x00000000)
- Prefix                   : 240e:fe:8ca7:ea01::/64
-On-link                 :          Yes
-Autonomous address conf.:          Yes
-Valid time              :      2592000 (0x00278d00) seconds
-Pref. time              :        14400 (0x00003840) seconds
- Prefix                   : fc00:470:f1cd:101::/64
-On-link                 :          Yes
-Autonomous address conf.:          Yes
-Valid time              :      2592000 (0x00278d00) seconds
-Pref. time              :        14400 (0x00003840) seconds
- Recursive DNS server     : fc00:470:f1cd::ff00
-DNS server lifetime     :          600 (0x00000258) seconds
- Source link-layer address: 00:98:2B:F8:3F:11
- from fe80::298:2bff:fef8:3f11
-:::
-```
-
-
-### Neighbor Discovery
-
-```{opcmd} force ipv6-nd interface \<interface\> address \<ipv6-address\>
-
-Example:
-
-:::{code-block} none
-vyos@vyos:~$ force ipv6-nd interface eth0 address fc00:470:f1cd:101::1
-
-Soliciting fc00:470:f1cd:101::1 (fc00:470:f1cd:101::1) on eth0...
-Target link-layer address: 00:98:2B:F8:3F:11 from fc00:470:f1cd:101::1
-:::
-```
\ No newline at end of file
diff --git a/docs/troubleshooting/md-index.md b/docs/troubleshooting/md-index.md
deleted file mode 100644
index 31dbd87b..00000000
--- a/docs/troubleshooting/md-index.md
+++ /dev/null
@@ -1,17 +0,0 @@
-(troubleshooting)=
-
-# Troubleshooting
-
-Sometimes things break or don't work as expected. This section describes
-several troubleshooting tools provided by VyOS that can help when something
-goes wrong.
-
-```{toctree}
-:maxdepth: 1
-
-connectivity
-interfaces
-monitoring
-terminal
-system
-```
diff --git a/docs/troubleshooting/md-interfaces.md b/docs/troubleshooting/md-interfaces.md
deleted file mode 100644
index 553cbf90..00000000
--- a/docs/troubleshooting/md-interfaces.md
+++ /dev/null
@@ -1,36 +0,0 @@
-# Interface Names
-
-If you find the names of your interfaces have changed, this could be because
-your MAC addresses have changed.
-
-- For example, you have a VyOS VM with 4 Ethernet interfaces named
-  eth0, eth1, eth2 and eth3. Then, you migrate your VyOS VM to a different
-  host and find your interfaces now are eth4, eth5, eth6 and eth7.
-
-  One way to fix this issue **taking control of the MAC addresses** is:
-
-  Log into VyOS and run this command to display your interface settings.
-
-  ```none
-  show interfaces detail
-  ```
-
-  Take note of MAC addresses.
-
-  Now, in order to update a MAC address in the configuration, run this command
-  specifying the interface name and MAC address you want.
-
-  ```none
-  set interfaces ethernet eth0 hw-id 00:0c:29:da:a4:fe
-  ```
-
-  If it is a VM, go into the settings of the host and set the MAC address to
-  the settings found in the config.boot file. You can also set the MAC to
-  static if the host allows so.
-
-- Another example could be when cloning VyOS VMs in GNS3 and you get into the
-  same issue: interface names have changed.
-
-  And **a more generic way to fix it** is just deleting every MAC address at
-  the configuration file of the cloned machine. They will be correctly
-  regenerated automatically.
diff --git a/docs/troubleshooting/md-monitoring.md b/docs/troubleshooting/md-monitoring.md
deleted file mode 100644
index 778bb057..00000000
--- a/docs/troubleshooting/md-monitoring.md
+++ /dev/null
@@ -1,152 +0,0 @@
-# Monitoring
-
-VyOS features several monitoring tools.
-
-```none
-vyos@vyos:~$ monitor
-Possible completions:
-  bandwidth     Monitor interface bandwidth in real time
-  bandwidth-test
-                Initiate or wait for bandwidth test
-  cluster       Monitor clustering service
-  command       Monitor an operational mode command (refreshes every 2 seconds)
-  conntrack-sync
-                Monitor conntrack-sync
-  content-inspection
-                Monitor Content-Inspection
-  dhcp          Monitor Dynamic Host Control Protocol (DHCP)
-  dns           Monitor a Domain Name Service (DNS) daemon
-  firewall      Monitor Firewall
-  https         Monitor the Secure Hypertext Transfer Protocol (HTTPS) service
-  lldp          Monitor Link Layer Discovery Protocol (LLDP) daemon
-  log           Monitor last lines of messages file
-  nat           Monitor network address translation (NAT)
-  ndp           Monitor the NDP information received by the router through the device
-  openvpn       Monitor OpenVPN
-  protocol      Monitor routing protocols
-  snmp          Monitor Simple Network Management Protocol (SNMP) daemon
-  stop-all      Stop all current background monitoring processes
-  traceroute    Monitor the path to a destination in realtime
-  traffic       Monitor traffic dumps
-  vpn           Monitor VPN
-  vrrp          Monitor Virtual Router Redundancy Protocol (VRRP)
-  webproxy      Monitor Webproxy service
-```
-
-
-## Traffic Dumps
-
-To monitor interface traffic, issue the {code}`monitor traffic interface <name>`
-command, replacing `<name>` with your chosen interface.
-
-```none
-vyos@vyos:~$ monitor traffic interface eth0
-tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
-listening on eth0, link-type EN10MB (Ethernet), capture size 262144 bytes
-15:54:28.581601 IP 192.168.0.1 > vyos: ICMP echo request, id 1870, seq 3848, length 64
-15:54:28.581660 IP vyos > 192.168.0.1: ICMP echo reply, id 1870, seq 3848, length 64
-15:54:29.583399 IP 192.168.0.1 > vyos: ICMP echo request, id 1870, seq 3849, length 64
-15:54:29.583454 IP vyos > 192.168.0.1: ICMP echo reply, id 1870, seq 3849, length 64
-^C
-4 packets captured
-4 packets received by filter
-0 packets dropped by kernel
-vyos@vyos:~$
-```
-
-To quit monitoring, press {kbd}`Ctrl-C` and you'll be returned to the VyOS command
-prompt.
-
-Traffic can be filtered and saved.
-
-```none
-vyos@vyos:~$ monitor traffic interface eth0
-Possible completions:
-  <Enter>       Execute the current command
-  filter        Monitor traffic matching filter conditions
-  save          Save traffic dump from an interface to a file
-```
-
-
-## Interface Bandwidth Usage
-
-To quickly view the bandwidth usage of an interface, use the `monitor bandwidth` command:
-
-```none
-vyos@vyos:~$ monitor bandwidth interface eth0
-```
-
-This shows the following:
-
-```none
-     B                      (RX Bytes/second)
-198.00 .|....|.....................................................
-165.00 .|....|.....................................................
-132.00 ||..|.|.....................................................
- 99.00 ||..|.|.....................................................
- 66.00 |||||||.....................................................
- 33.00 |||||||.....................................................
-       1   5   10   15   20   25   30   35   40   45   50   55   60
-
-   KiB                      (TX Bytes/second)
-  3.67 ......|.....................................................
-  3.06 ......|.....................................................
-  2.45 ......|.....................................................
-  1.84 ......|.....................................................
-  1.22 ......|.....................................................
-  0.61 :::::||.....................................................
-       1   5   10   15   20   25   30   35   40   45   50   55   60
-```
-
-
-## Interface Performance
-
-To take a look on the network bandwidth between two nodes, the `monitor
-bandwidth-test` command is used to run iperf.
-
-```none
-vyos@vyos:~$ monitor bandwidth-test
-Possible completions:
-  accept        Wait for bandwidth test connections (port TCP/5001)
-  initiate      Initiate a bandwidth test
-```
-
-- The `accept` command opens a listening iperf server on TCP Port 5001
-- The `initiate` command connects to that server to perform the test.
-
-```none
-vyos@vyos:~$ monitor bandwidth-test initiate
-Possible completions:
-  <hostname>    Initiate a bandwidth test to specified host (port TCP/5001)
-  <x.x.x.x>
-  <h:h:h:h:h:h:h:h>
-```
-
-
-## Monitor command
-
-The `monitor command` command allows you to repeatedly run a command to view
-a continuously refreshed output. The command is run and output every 2 seconds,
-allowing you to monitor the output continuously without having to re-run the
-command. This can be useful to follow routing adjacency formation.
-
-```none
-vyos@router:~$ monitor command "show interfaces"
-```
-
-Will clear the screen and show you the output of `show interfaces` every
-2 seconds.
-
-```none
-Every 2.0s: /opt/vyatta/bin/vyatta-op-cmd-wrapper    Sun Mar 26 02:49:46 2019
-
-Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
-Interface        IP Address                        S/L  Description
----------        ----------                        ---  -----------
-eth0             192.168.1.1/24                    u/u
-eth0.5           198.51.100.4/24                   u/u  WAN
-lo               127.0.0.1/8                       u/u
-                 ::1/128
-vti0             172.25.254.2/30                   u/u
-vti1             172.25.254.9/30                   u/u
-```
diff --git a/docs/troubleshooting/md-system.md b/docs/troubleshooting/md-system.md
deleted file mode 100644
index e855e385..00000000
--- a/docs/troubleshooting/md-system.md
+++ /dev/null
@@ -1,48 +0,0 @@
-# System Information
-
-(boot-steps)=
-
-## Boot Steps
-
-VyOS 1.2 uses [Debian Jessie] as the base Linux operating system. Jessie was
-the first version of Debian that uses [systemd] as the default init system.
-
-These are the boot steps for VyOS 1.2
-
-1. The BIOS loads Grub (or isolinux for the Live CD)
-2. Grub then starts the Linux boot and loads the Linux Kernel `/boot/vmlinuz`
-3. Kernel Launches Systemd `/lib/systemd/systemd`
-4. Systemd loads the VyOS service file
-   `/lib/systemd/system/vyos-router.service`
-5. The service file launches the VyOS router init script
-   `/usr/libexec/vyos/init/vyos-router` - this is part of the [vyatta-cfg]
-   Debian package
-
-> 1. Starts [FRR] - successor to [GNU Zebra] and [Quagga]
-> 2. Initialises the boot configuration file - copies over
->    `config.boot.default` if there is no configuration
-> 3. Runs the configuration migration, if the configuration is for an older
->    version of VyOS
-> 4. Runs The pre-config script, if there is one
->    `/config/scripts/vyos-preconfig-bootup.script`
-> 5. If the config file was upgraded, runs any post upgrade scripts
->    `/config/scripts/post-upgrade.d`
-> 6. Starts `rl-system` and `firewall`
-> 7. Mounts the `/boot` partition
-> 8. The boot configuration file is then applied by `/opt/vyatta/sbin/vyatta-boot-config-loader/opt/vyatta/etc/config/config.boot`
->
-> > 1. The config loader script writes log entries to
-> >    `/var/log/vyatta-config-loader.log`
->
-> 09. Runs `telinit q` to tell the init system to reload `/etc/inittab`
-> 10. Finally it runs the post-config script
->     `/config/scripts/vyos-postconfig-bootup.script`
-
-[debian jessie]: https://www.debian.org/releases/jessie/
-[frr]: https://frrouting.org/
-[gnu zebra]: https://www.gnu.org/software/zebra/
-[pcap filter expressions]: http://www.tcpdump.org/manpages/pcap-filter.7.html
-[quagga]: https://www.quagga.net/
-[systemd]: https://freedesktop.org/wiki/Software/systemd/
-[tshark]: https://www.wireshark.org/docs/man-pages/tshark.html
-[vyatta-cfg]: https://github.com/vyos/vyatta-cfg
diff --git a/docs/troubleshooting/md-terminal.md b/docs/troubleshooting/md-terminal.md
deleted file mode 100644
index 0d421972..00000000
--- a/docs/troubleshooting/md-terminal.md
+++ /dev/null
@@ -1,39 +0,0 @@
-# Terminal/Console
-
-Sometimes you need to clear counters or statistics to troubleshoot better.
-
-To do this use the `clear` command in Operational mode.
-
-to clear the console output
-
-```none
-vyos@vyos:~$ clear console
-```
-
-to clear interface counters
-
-```none
-# clear all interfaces
-vyos@vyos:~$ clear interface ethernet counters
-# clear specific interface
-vyos@vyos:~$ clear interface ethernet eth0 counters
-```
-
-The command follows the same logic as the `set` command in configuration mode.
-
-```none
-# clear all counters of an interface type
-vyos@vyos:~$ clear interface <interface_type> counters
-# clear counter of an interface in interface_type
-vyos@vyos:~$ clear interface <interface_type> <interface_name> counters
-```
-
-to clear counters on firewall rulesets or single rules
-
-```none
-vyos@vyos:~$ clear firewall name <ipv4 ruleset name> counters
-vyos@vyos:~$ clear firewall name <ipv4 ruleset name> rule <rule#> counters
-
-vyos@vyos:~$ clear firewall ipv6-name <ipv6 ruleset name> counters
-vyos@vyos:~$ clear firewall ipv6-name <ipv6 ruleset name> rule <rule#> counters
-```