diff options
| -rw-r--r-- | docs/configexamples/zone-policy.rst | 8 | ||||
| -rw-r--r-- | docs/configuration/firewall/bridge.rst | 8 | ||||
| -rw-r--r-- | docs/configuration/firewall/ipv4.rst | 8 | ||||
| -rw-r--r-- | docs/configuration/firewall/ipv6.rst | 10 | ||||
| -rw-r--r-- | docs/configuration/policy/route.rst | 6 |
5 files changed, 20 insertions, 20 deletions
diff --git a/docs/configexamples/zone-policy.rst b/docs/configexamples/zone-policy.rst index 08db13b9..d9a6bf89 100644 --- a/docs/configexamples/zone-policy.rst +++ b/docs/configexamples/zone-policy.rst @@ -145,7 +145,7 @@ To add logging to the default rule, do: .. code-block:: none - set firewall name <ruleSet> enable-default-log + set firewall name <ruleSet> default-log By default, iptables does not allow traffic for established sessions to @@ -251,7 +251,7 @@ Since we have 4 zones, we need to setup the following rulesets. Dmz-local Even if the two zones will never communicate, it is a good idea to -create the zone-pair-direction rulesets and set enable-default-log. This +create the zone-pair-direction rulesets and set default-log. This will allow you to log attempts to access the networks. Without it, you will never see the connection attempts. @@ -261,7 +261,7 @@ This is an example of the three base rules. name wan-lan { default-action drop - enable-default-log + default-log rule 1 { action accept state { @@ -285,7 +285,7 @@ Here is an example of an IPv6 DMZ-WAN ruleset. ipv6-name dmz-wan-6 { default-action drop - enable-default-log + default-log rule 1 { action accept state { diff --git a/docs/configuration/firewall/bridge.rst b/docs/configuration/firewall/bridge.rst index 9fb019c5..bba9e56f 100644 --- a/docs/configuration/firewall/bridge.rst +++ b/docs/configuration/firewall/bridge.rst @@ -157,8 +157,8 @@ log options can be defined. Enable logging for the matched packet. If this configuration command is not present, then log is not enabled. -.. cfgcmd:: set firewall bridge forward filter enable-default-log -.. cfgcmd:: set firewall bridge name <name> enable-default-log +.. cfgcmd:: set firewall bridge forward filter default-log +.. cfgcmd:: set firewall bridge name <name> default-log Use this command to enable the logging of the default action on the specified chain. @@ -325,7 +325,7 @@ Configuration example: .. code-block:: none set firewall bridge forward filter default-action 'drop' - set firewall bridge forward filter enable-default-log + set firewall bridge forward filter default-log set firewall bridge forward filter rule 10 action 'continue' set firewall bridge forward filter rule 10 inbound-interface name 'eth2' set firewall bridge forward filter rule 10 vlan id '22' @@ -341,7 +341,7 @@ Configuration example: set firewall bridge forward filter rule 40 destination mac-address '66:55:44:33:22:11' set firewall bridge forward filter rule 40 source mac-address '11:22:33:44:55:66' set firewall bridge name TEST default-action 'accept' - set firewall bridge name TEST enable-default-log + set firewall bridge name TEST default-log set firewall bridge name TEST rule 10 action 'continue' set firewall bridge name TEST rule 10 log set firewall bridge name TEST rule 10 vlan priority '0' diff --git a/docs/configuration/firewall/ipv4.rst b/docs/configuration/firewall/ipv4.rst index ff739418..1cf50810 100644 --- a/docs/configuration/firewall/ipv4.rst +++ b/docs/configuration/firewall/ipv4.rst @@ -206,10 +206,10 @@ log options can be defined. Enable logging for the matched packet. If this configuration command is not present, then log is not enabled. -.. cfgcmd:: set firewall ipv4 forward filter enable-default-log -.. cfgcmd:: set firewall ipv4 input filter enable-default-log -.. cfgcmd:: set firewall ipv4 output filter enable-default-log -.. cfgcmd:: set firewall ipv4 name <name> enable-default-log +.. cfgcmd:: set firewall ipv4 forward filter default-log +.. cfgcmd:: set firewall ipv4 input filter default-log +.. cfgcmd:: set firewall ipv4 output filter default-log +.. cfgcmd:: set firewall ipv4 name <name> default-log Use this command to enable the logging of the default action on the specified chain. diff --git a/docs/configuration/firewall/ipv6.rst b/docs/configuration/firewall/ipv6.rst index 0aa8a137..c679ffd5 100644 --- a/docs/configuration/firewall/ipv6.rst +++ b/docs/configuration/firewall/ipv6.rst @@ -206,10 +206,10 @@ log options can be defined. Enable logging for the matched packet. If this configuration command is not present, then log is not enabled. -.. cfgcmd:: set firewall ipv6 forward filter enable-default-log -.. cfgcmd:: set firewall ipv6 input filter enable-default-log -.. cfgcmd:: set firewall ipv6 output filter enable-default-log -.. cfgcmd:: set firewall ipv6 name <name> enable-default-log +.. cfgcmd:: set firewall ipv6 forward filter default-log +.. cfgcmd:: set firewall ipv6 input filter default-log +.. cfgcmd:: set firewall ipv6 output filter default-log +.. cfgcmd:: set firewall ipv6 name <name> default-log Use this command to enable the logging of the default action on the specified chain. @@ -1177,7 +1177,7 @@ Example Partial Config } name INP-ETH1 { default-action drop - enable-default-log + default-log rule 10 { action accept protocol tcp_udp diff --git a/docs/configuration/policy/route.rst b/docs/configuration/policy/route.rst index 1a85ffc6..45975774 100644 --- a/docs/configuration/policy/route.rst +++ b/docs/configuration/policy/route.rst @@ -19,8 +19,8 @@ from 1 - 999999, at the first match the action of the rule will be executed. Provide a rule-set description. -.. cfgcmd:: set policy route <name> enable-default-log -.. cfgcmd:: set policy route6 <name> enable-default-log +.. cfgcmd:: set policy route <name> default-log +.. cfgcmd:: set policy route6 <name> default-log Option to log packets hitting default-action. @@ -271,4 +271,4 @@ setting a different routing table. .. cfgcmd:: set policy route <name> rule <n> set tcp-mss <500-1460> .. cfgcmd:: set policy route6 <name> rule <n> set tcp-mss <500-1460> - Set packet modifications: Explicitly set TCP Maximum segment size value.
\ No newline at end of file + Set packet modifications: Explicitly set TCP Maximum segment size value. |