diff options
Diffstat (limited to 'docs/configuration-overview.rst')
| -rw-r--r-- | docs/configuration-overview.rst | 40 |
1 files changed, 20 insertions, 20 deletions
diff --git a/docs/configuration-overview.rst b/docs/configuration-overview.rst index ca8dc448..bb8544d5 100644 --- a/docs/configuration-overview.rst +++ b/docs/configuration-overview.rst @@ -11,7 +11,7 @@ of system configuration. The current active configuration -aka running configuration- can be viewed using the show configuration command. -.. code-block:: sh +.. code-block:: console vyos@vyos:~$ show configuration interfaces { @@ -75,7 +75,7 @@ through a collection of ``set`` and ``delete`` commands. Get a collection of all the set commands required which led to this running configuration. -.. code-block:: sh +.. code-block:: console vyos@vyos:~$ show configuration commands set interfaces ethernet eth0 address 'dhcp' @@ -131,7 +131,7 @@ When entering the configuration mode you are navigating inside the tree structure exported in the overview above, to enter configuration mode enter the command ``configure`` when in operational mode. -.. code-block:: sh +.. code-block:: console vyos@vyos$ configure [edit] @@ -146,7 +146,7 @@ lengthy when manually typing them. To change the current hierarchy level use the command: ``edit`` -.. code-block:: sh +.. code-block:: console [edit] vyos@vyos# edit interfaces ethernet eth0 @@ -163,7 +163,7 @@ The ``show`` command within configuration mode will show the working configuration indicating line changes with ``+`` for additions, ``>`` for replacements and ``-`` for deletions. -.. code-block:: sh +.. code-block:: console vyos@vyos:~$ configure [edit] @@ -197,7 +197,7 @@ replacements and ``-`` for deletions. It is also possible to display all `set` commands within configuration mode using ``show | commands`` -.. code-block:: sh +.. code-block:: console vyos@vyos# show interfaces ethernet eth0 | commands set address dhcp @@ -206,7 +206,7 @@ using ``show | commands`` These commands are also relative to the level you are inside and only relevant configuration blocks will be displayed when entering a sub-level. -.. code-block:: sh +.. code-block:: console [edit interfaces ethernet eth0] vyos@vyos# show @@ -217,7 +217,7 @@ Exiting from the configuration mode is done via the ``exit`` command from the top level, executing `exit` from within a sub-level takes you back to the top level. -.. code-block:: sh +.. code-block:: console [edit interfaces ethernet eth0] vyos@vyos# exit @@ -239,7 +239,7 @@ These commands are also relative to the level where they are executed and all redundant information from the current level is removed from the command entered. -.. code-block:: sh +.. code-block:: console [edit] vyos@vyos# set interface ethernet eth0 address 192.0.2.100/24 @@ -255,7 +255,7 @@ all sub-levels under the current level you've specified in the ``delete`` command. Deleting an entry will also result in the element reverting back to its default value if one exists. -.. code-block:: sh +.. code-block:: console [edit interfaces ethernet eth0] vyos@vyos# delete address 192.0.2.100/24 @@ -263,7 +263,7 @@ its default value if one exists. Any change you do on the configuration, will not take effect until committed using the ``commit`` command in configuration mode. -.. code-block:: sh +.. code-block:: console vyos@vyos# commit [edit] @@ -275,7 +275,7 @@ In order to preserve configuration changes upon reboot, the configuration must also be saved once applied. This is done using the ``save`` command in configuration mode. -.. code-block:: sh +.. code-block:: console vyos@vyos# save Saving configuration to '/config/config.boot'... @@ -288,7 +288,7 @@ Configuration mode can not be exited while uncommitted changes exist. To exit configuration mode without applying changes, the exit discard command can be used. -.. code-block:: sh +.. code-block:: console vyos@vyos# exit Cannot exit: configuration modified. @@ -298,7 +298,7 @@ used. exit vyos@vyos:~$ -.. code-block:: sh +.. code-block:: console vyos@vyos# save [tab] Possible completions: @@ -324,7 +324,7 @@ operational mode. Command completion and syntax help with ``?`` and ``[tab]`` will also work. -.. code-block:: sh +.. code-block:: console [edit] vyos@vyos# run show interfaces @@ -347,7 +347,7 @@ previous revisions if anything goes wrong. To view existing revisions, use ``show system commit`` operational mode command. -.. code-block:: sh +.. code-block:: console vyos@vyos-test-2# run show system commit 0 2015-03-30 08:53:03 by vyos via cli @@ -362,7 +362,7 @@ To view existing revisions, use ``show system commit`` operational mode command. To compare configuration revisions in configuration mode, use the compare command: -.. code-block:: sh +.. code-block:: console vyos@vyos# compare [tab] Possible completions: @@ -395,7 +395,7 @@ compared to Y, indicating with a plus sign (``+``) the additional parts X has when compared to y, and indicating with a minus sign (``-``) the lacking parts x misses when compared to y. -.. code-block:: sh +.. code-block:: console vyos@vyos-test-2# compare 0 6 [edit interfaces] @@ -416,7 +416,7 @@ Rolling Back Changes You can rollback configuration using the rollback command. This command will apply the selected revision and trigger a system reboot. -.. code-block:: sh +.. code-block:: console vyos@vyos# compare 1 [edit system] @@ -459,7 +459,7 @@ Restore Default In the case you want to completely delete your configuration and restore the default one, you can enter the following command in configuration mode: -.. code-block:: sh +.. code-block:: console load /opt/vyatta/etc/config.boot.default |