1 files changed, 192 insertions, 0 deletions
diff --git a/docs/configuration/interfaces/l2tpv3.rst b/docs/configuration/interfaces/l2tpv3.rst
new file mode 100644
index 00000000..4c9cbf9b
--- /dev/null
+++ b/docs/configuration/interfaces/l2tpv3.rst
@@ -0,0 +1,192 @@
+.. include:: ../_include/need_improvement.txt
+
+.. _l2tpv3-interface:
+
+######
+L2TPv3
+######
+
+Layer 2 Tunnelling Protocol Version 3 is an IETF standard related to L2TP that
+can be used as an alternative protocol to :ref:`mpls` for encapsulation of
+multiprotocol Layer 2 communications traffic over IP networks. Like L2TP,
+L2TPv3 provides a pseudo-wire service, but scaled to fit carrier requirements.
+
+L2TPv3 can be regarded as being to MPLS what IP is to ATM: a simplified version
+of the same concept, with much of the same benefit achieved at a fraction of the
+effort, at the cost of losing some technical features considered less important
+in the market.
+
+In the case of L2TPv3, the features lost are teletraffic engineering features
+considered important in MPLS. However, there is no reason these features could
+not be re-engineered in or on top of L2TPv3 in later products.
+
+The protocol overhead of L2TPv3 is also significantly bigger than MPLS.
+
+L2TPv3 is described in :rfc:`3921`.
+
+*************
+Configuration
+*************
+
+Common interface configuration
+==============================
+
+.. cmdinclude:: ../_include/interface-common-without-dhcp.txt
+   :var0: l2tpv3
+   :var1: l2tpeth0
+
+L2TPv3 options
+==============
+
+.. cfgcmd:: set interfaces l2tpv3 <interface> encapsulation <udp | ip>
+
+  Set the encapsulation type of the tunnel. Valid values for encapsulation are:
+  udp, ip.
+
+  This defaults to UDP
+
+.. cfgcmd:: set interfaces l2tpv3 <interface> local-ip <address>
+
+  set the IP address of the local interface to be used for the tunnel.
+
+  This address must be the address of a local interface. May be specified as an
+  IPv4 address or an IPv6 address.
+
+.. cfgcmd:: set interfaces l2tpv3 <interface> remote-ip <address>
+
+  Set the IP address of the remote peer. May be specified as an IPv4 address or
+  an IPv6 address.
+
+.. cfgcmd:: set interfaces l2tpv3 <interface> session-id <id>
+
+  Set the session id, which is a 32-bit integer value. Uniquely identifies the
+  session being created. The value used must match the peer_session_id value
+  being used at the peer.
+
+.. cfgcmd:: set interfaces l2tpv3 <interface> peer-session-id <id>
+
+  Set the peer session id, which is a 32-bit integer value assigned to the
+  session by the peer. The value used must match the session_id value being
+  used at the peer.
+
+.. cfgcmd:: set interfaces l2tpv3 <interface> tunnel-id <id>
+
+  Set the tunnel id, which is a 32-bit integer value. Uniquely identifies the
+  tunnel into which the session will be created.
+
+.. cfgcmd:: set interfaces l2tpv3 <interface> peer-tunnel-id <id>
+
+  Set the tunnel id, which is a 32-bit integer value. Uniquely identifies the
+  tunnel into which the session will be created.
+
+*******
+Example
+*******
+
+Over IP
+=======
+
+.. code-block:: none
+
+  # show interfaces l2tpv3
+  l2tpv3 l2tpeth10 {
+      address 192.168.37.1/27
+      encapsulation ip
+      local-ip 192.0.2.1
+      peer-session-id 100
+      peer-tunnel-id 200
+      remote-ip 203.0.113.24
+      session-id 100
+      tunnel-id 200
+  }
+
+Inverse configuration has to be applied to the remote side.
+
+Over UDP
+========
+
+UDP mode works better with NAT:
+
+* Set local-ip to your local IP (LAN).
+* Add a forwarding rule matching UDP port on your internet router.
+
+.. code-block:: none
+
+  # show interfaces l2tpv3
+  l2tpv3 l2tpeth10 {
+      address 192.168.37.1/27
+      destination-port 9001
+      encapsulation udp
+      local-ip 192.0.2.1
+      peer-session-id 100
+      peer-tunnel-id 200
+      remote-ip 203.0.113.24
+      session-id 100
+      source-port 9000
+      tunnel-id 200
+  }
+
+To create more than one tunnel, use distinct UDP ports.
+
+
+Over IPSec, L2 VPN (bridge)
+===========================
+
+This is the LAN extension use case. The eth0 port of the distant VPN peers
+will be directly connected like if there was a switch between them.
+
+IPSec:
+
+.. code-block:: none
+
+  set vpn ipsec ipsec-interfaces <VPN-interface>
+  set vpn ipsec esp-group test-ESP-1 compression 'disable'
+  set vpn ipsec esp-group test-ESP-1 lifetime '3600'
+  set vpn ipsec esp-group test-ESP-1 mode 'transport'
+  set vpn ipsec esp-group test-ESP-1 pfs 'enable'
+  set vpn ipsec esp-group test-ESP-1 proposal 1 encryption 'aes128'
+  set vpn ipsec esp-group test-ESP-1 proposal 1 hash 'sha1'
+  set vpn ipsec ike-group test-IKE-1 ikev2-reauth 'no'
+  set vpn ipsec ike-group test-IKE-1 key-exchange 'ikev1'
+  set vpn ipsec ike-group test-IKE-1 lifetime '3600'
+  set vpn ipsec ike-group test-IKE-1 proposal 1 dh-group '5'
+  set vpn ipsec ike-group test-IKE-1 proposal 1 encryption 'aes128'
+  set vpn ipsec ike-group test-IKE-1 proposal 1 hash 'sha1'
+  set vpn ipsec site-to-site peer <peer-ip> authentication mode 'pre-shared-secret'
+  set vpn ipsec site-to-site peer <peer-ip> authentication pre-shared-secret <pre-shared-key>
+  set vpn ipsec site-to-site peer <peer-ip> connection-type 'initiate'
+  set vpn ipsec site-to-site peer <peer-ip> ike-group 'test-IKE-1'
+  set vpn ipsec site-to-site peer <peer-ip> ikev2-reauth 'inherit'
+  set vpn ipsec site-to-site peer <peer-ip> local-address <local-ip>
+  set vpn ipsec site-to-site peer <peer-ip> tunnel 1 allow-nat-networks 'disable'
+  set vpn ipsec site-to-site peer <peer-ip> tunnel 1 allow-public-networks 'disable'
+  set vpn ipsec site-to-site peer <peer-ip> tunnel 1 esp-group 'test-ESP-1'
+  set vpn ipsec site-to-site peer <peer-ip> tunnel 1 protocol 'l2tp'
+
+Bridge:
+
+.. code-block:: none
+
+  set interfaces bridge br0 description 'L2 VPN Bridge'
+  # remote side in this example:
+  # set interfaces bridge br0 address '172.16.30.18/30'
+  set interfaces bridge br0 address '172.16.30.17/30'
+  set interfaces bridge br0 member interface eth0
+  set interfaces ethernet eth0 description 'L2 VPN Physical port'
+
+L2TPv3:
+
+.. code-block:: none
+
+  set interfaces bridge br0 member interface 'l2tpeth0'
+  set interfaces l2tpv3 l2tpeth0 description 'L2 VPN Tunnel'
+  set interfaces l2tpv3 l2tpeth0 destination-port '5000'
+  set interfaces l2tpv3 l2tpeth0 encapsulation 'ip'
+  set interfaces l2tpv3 l2tpeth0 local-ip <local-ip>
+  set interfaces l2tpv3 l2tpeth0 mtu '1500'
+  set interfaces l2tpv3 l2tpeth0 peer-session-id '110'
+  set interfaces l2tpv3 l2tpeth0 peer-tunnel-id '10'
+  set interfaces l2tpv3 l2tpeth0 remote-ip <peer-ip>
+  set interfaces l2tpv3 l2tpeth0 session-id '110'
+  set interfaces l2tpv3 l2tpeth0 source-port '5000'
+  set interfaces l2tpv3 l2tpeth0 tunnel-id '10'