3 files changed, 21 insertions, 7 deletions
diff --git a/docs/configuration/interfaces/vxlan.rst b/docs/configuration/interfaces/vxlan.rst
index 2cb0b2f1..a84ed16f 100644
--- a/docs/configuration/interfaces/vxlan.rst
+++ b/docs/configuration/interfaces/vxlan.rst
@@ -67,15 +67,27 @@ VXLAN specific options
   Source IP address used for VXLAN underlay. This is mandatory when using VXLAN
   via L2VPN/EVPN.
 
-.. cfgcmd:: set interfaces vxlan <interface> external
+.. cfgcmd:: set interfaces vxlan <interface> gpe
+
+  Enables the Generic Protocol extension (VXLAN-GPE). Currently, this is only
+  supported together with the external keyword.
+
+.. cfgcmd:: set interfaces vxlan <interface> parameters external
 
   Specifies whether an external control plane (e.g. BGP L2VPN/EVPN) or the
   internal FDB should be used.
 
-.. cfgcmd:: set interfaces vxlan <interface> gpe
+.. cfgcmd:: set interfaces vxlan <interface> parameters neighbor-suppress
 
-  Eenables the Generic Protocol extension (VXLAN-GPE). Currently, this is only
-  supported together with the external keyword.
+  In order to minimize the flooding of ARP and ND messages in the VXLAN network,
+  EVPN includes provisions :rfc:`7432#section-10` that allow participating VTEPs
+  to suppress such messages in case they know the MAC-IP binding and can reply
+  on behalf of the remote host.
+
+.. cfgcmd:: set interfaces vxlan <interface> parameters nolearning
+
+   Specifies if unknown source link layer addresses and IP addresses are entered
+   into the VXLAN device forwarding database.
 
 Unicast
 ^^^^^^^
@@ -155,7 +167,7 @@ interface is no longer required for each VNI.
    .. code-block:: none
 
     set interfaces bridge br0 member interface vxlan0
-    set interfaces vxlan vxlan0 external
+    set interfaces vxlan vxlan0 parameters external
     set interfaces vxlan vxlan0 source-interface 'dum0'
     set interfaces vxlan vxlan0 vlan-to-vni 10 vni '10010'
     set interfaces vxlan vxlan0 vlan-to-vni 11 vni '10011'
diff --git a/docs/configuration/interfaces/wireguard.rst b/docs/configuration/interfaces/wireguard.rst
index 8b829b64..885720e1 100644
--- a/docs/configuration/interfaces/wireguard.rst
+++ b/docs/configuration/interfaces/wireguard.rst
@@ -222,7 +222,7 @@ firewall exception.
     set firewall ipv4 name OUTSIDE_LOCAL rule 20 protocol udp
     set firewall ipv4 name OUTSIDE_LOCAL rule 20 source
 
-You should also ensure that the OUTISDE_LOCAL firewall group is applied to the
+You should also ensure that the OUTSIDE_LOCAL firewall group is applied to the
 WAN interface and a direction (local).
 
 .. code-block:: none
@@ -413,7 +413,7 @@ the VyOS CLI.
   into the VyOS CLI if needed. The supplied ``<name>`` on the CLI will become
   the peer name in the snippet.
 
-  In addition you will specifiy the IP address or FQDN for the client where it
+  In addition you will specify the IP address or FQDN for the client where it
   will connect to. The address parameter can be used up to two times and is used
   to assign the clients specific IPv4 (/32) or IPv6 (/128) address.
 
diff --git a/docs/configuration/interfaces/wireless.rst b/docs/configuration/interfaces/wireless.rst
index e853a1ec..df153763 100644
--- a/docs/configuration/interfaces/wireless.rst
+++ b/docs/configuration/interfaces/wireless.rst
@@ -562,6 +562,7 @@ The WAP in this example has the following characteristics:
   set interfaces wireless wlan0 security wpa mode wpa2
   set interfaces wireless wlan0 security wpa cipher CCMP
   set interfaces wireless wlan0 security wpa passphrase '12345678'
+  set interfaces wireless wlan0 country-code de
 
 Resulting in
 
@@ -572,6 +573,7 @@ Resulting in
     wireless wlan0 {
           address 192.168.2.1/24
           channel 1
+          country-code de
           mode n
           security {
               wpa {