diff options
Diffstat (limited to 'docs/routing/static.rst')
| -rw-r--r-- | docs/routing/static.rst | 131 |
1 files changed, 116 insertions, 15 deletions
diff --git a/docs/routing/static.rst b/docs/routing/static.rst index dc0e1ab4..cebe42fa 100644 --- a/docs/routing/static.rst +++ b/docs/routing/static.rst @@ -1,29 +1,130 @@ -.. _routing-static: +.. _static-routing: + +###### +Static +###### + +Static routes are manually configured routes, which, in general, cannot be +updated dynamically from information VyOS learns about the network topology from +other routing protocols. However, if a link fails, the router will remove +routes, including static routes, from the :abbr:`RIPB (Routing Information +Base)` that used this interface to reach the next hop. In general, static +routes should only be used for very simple network topologies, or to override +the behavior of a dynamic routing protocol for a small number of routes. The +collection of all routes the router has learned from its configuration or from +its dynamic routing protocols is stored in the RIB. Unicast routes are directly +used to determine the forwarding table used for unicast packet forwarding. -############# Static Routes ############# -Static routes are manually configured network routes. +.. cfgcmd:: set protocols static route '<subnet>' next-hop '<address>' + + Configure next-hop `<address>` for an IPv4 static route. Multiple static + routes can be created. + +.. cfgcmd:: set protocols static route '<subnet>' next-hop '<address>' disable -A typical use for a static route is a static default route for systems that do -not make use of DHCP or dynamic routing protocols: + Disable this IPv4 static route entry. -.. code-block:: none +.. cfgcmd:: set protocols static route '<subnet>' next-hop '<address>' distance '<distance>' - set protocols static route 0.0.0.0/0 next-hop 10.1.1.1 distance '1' + Defines next-hop distance for this route, routes with smaller administrative + distance are elected prior those with a higher distance. -Another common use of static routes is to blackhole (drop) traffic. In the -example below, :rfc:`1918` networks are set as blackhole routes. + Range is 1 to 255, default is 1. -This prevents these networks leaking out public interfaces, but it does not prevent -them from being used as the most specific route has the highest priority. +.. cfgcmd:: set protocols static route6 '<subnet>' next-hop '<address>' -.. code-block:: none + Configure next-hop `<address>` for an IPv6 static route. Multiple static + routes can be created. - set protocols static route 10.0.0.0/8 blackhole distance '254' - set protocols static route 172.16.0.0/12 blackhole distance '254' - set protocols static route 192.168.0.0/16 blackhole distance '254' +.. cfgcmd:: set protocols static route6 '<subnet>' next-hop '<address>' disable + + Disable this IPv6 static route entry. + +.. cfgcmd:: set protocols static route6 '<subnet>' next-hop '<address>' distance '<distance>' + + Defines next-hop distance for this route, routes with smaller administrative + distance are elected prior those with a higher distance. + + Range is 1 to 255, default is 1. .. note:: Routes with a distance of 255 are effectively disabled and not installed into the kernel. + + +Interface Routes +================ + +.. cfgcmd:: set protocols static interface-route '<subnet>' next-hop-interface '<interface>' + + Allows you to configure the next-hop interface for an interface-based IPv4 + static route. `<interface>` will be the next-hop interface where trafic is + routed for the given `<subnet>`. + +.. cfgcmd:: set protocols static interface-route '<subnet>' next-hop-interface '<interface>' disable + + Disables interface-based IPv4 static route. + +.. cfgcmd:: set protocols static interface-route '<subnet>' next-hop-interface '<interface>' distance '<distance>' + + Defines next-hop distance for this route, routes with smaller administrative + distance are elected prior those with a higher distance. + + Range is 1 to 255, default is 1. + +.. cfgcmd:: set protocols static interface-route6 '<subnet>' next-hop-interface '<interface>' + + Allows you to configure the next-hop interface for an interface-based IPv6 + static route. `<interface>` will be the next-hop interface where trafic is + routed for the given `<subnet>`. + +.. cfgcmd:: set protocols static interface-route6 '<subnet>' next-hop-interface '<interface>' disable + + Disables interface-based IPv6 static route. + +.. cfgcmd:: set protocols static interface-route6 '<subnet>' next-hop-interface '<interface>' distance '<distance>' + + Defines next-hop distance for this route, routes with smaller administrative + distance are elected prior those with a higher distance. + + Range is 1 to 255, default is 1. + + +Blackhole +========= + +.. cfgcmd:: set protocols static route '<subnet>' blackhole + + Use this command to configure a "black-hole" route on the router. A + black-hole route is a route for which the system silently discard packets + that are matched. This prevents networks leaking out public interfaces, but + it does not prevent them from being used as a more specific route inside your + network. + +.. cfgcmd:: set protocols static route '<subnet>' blackhole distance '<distance>' + + Defines blackhole distance for this route, routes with smaller administrative + distance are elected prior those with a higher distance. + +.. cfgcmd:: set protocols static route6 '<subnet>' blackhole + + Use this command to configure a "black-hole" route on the router. A + black-hole route is a route for which the system silently discard packets + that are matched. This prevents networks leaking out public interfaces, but + it does not prevent them from being used as a more specific route inside your + network. + +.. cfgcmd:: set protocols static route6 '<subnet>' blackhole distance '<distance>' + + Defines blackhole distance for this route, routes with smaller administrative + distance are elected prior those with a higher distance. + + +Alternate Routing Tables +======================== + +Alternate routing tables are used with policy based routing. + +TBD |