diff options
Diffstat (limited to 'docs')
| -rw-r--r-- | docs/configuration/protocols/ospf.rst | 72 | ||||
| -rw-r--r-- | docs/configuration/protocols/ospfv3.rst | 71 |
2 files changed, 72 insertions, 71 deletions
diff --git a/docs/configuration/protocols/ospf.rst b/docs/configuration/protocols/ospf.rst index ff7c5e64..ee6753c5 100644 --- a/docs/configuration/protocols/ospf.rst +++ b/docs/configuration/protocols/ospf.rst @@ -68,3 +68,75 @@ address and the node 1 sending the default route: set policy route-map CONNECT rule 10 action permit set policy route-map CONNECT rule 10 match interface lo + +OSPFv3 (IPv6) +############# + +A typical configuration using 2 nodes. + +**Node 1:** + +.. code-block:: none + + set protocols ospfv3 area 0.0.0.0 interface eth1 + set protocols ospfv3 area 0.0.0.0 range 2001:db8:1::/64 + set protocols ospfv3 parameters router-id 192.168.1.1 + set protocols ospfv3 redistribute connected + +**Node 2:** + +.. code-block:: none + + set protocols ospfv3 area 0.0.0.0 interface eth1 + set protocols ospfv3 area 0.0.0.0 range 2001:db8:2::/64 + set protocols ospfv3 parameters router-id 192.168.2.1 + set protocols ospfv3 redistribute connected + +.. note:: You can not easily redistribute IPv6 routes via OSPFv3 on a WireGuard + interface link. This requires you to configure link-local addresses manually + on the WireGuard interfaces, see :vytask:`T1483`. + +Example configuration for WireGuard interfaces: + +**Node 1** + +.. code-block:: none + + set interfaces wireguard wg01 address 'fe80::216:3eff:fe51:fd8c/64' + set interfaces wireguard wg01 address '192.168.0.1/24' + set interfaces wireguard wg01 peer ospf02 allowed-ips '::/0' + set interfaces wireguard wg01 peer ospf02 allowed-ips '0.0.0.0/0' + set interfaces wireguard wg01 peer ospf02 endpoint '10.1.1.101:12345' + set interfaces wireguard wg01 peer ospf02 pubkey 'ie3...=' + set interfaces wireguard wg01 port '12345' + set protocols ospfv3 parameters router-id 192.168.1.1 + set protocols ospfv3 area 0.0.0.0 interface 'wg01' + set protocols ospfv3 area 0.0.0.0 interface 'lo' + +**Node 2** + +.. code-block:: none + + set interfaces wireguard wg01 address 'fe80::216:3eff:fe0a:7ada/64' + set interfaces wireguard wg01 address '192.168.0.2/24' + set interfaces wireguard wg01 peer ospf01 allowed-ips '::/0' + set interfaces wireguard wg01 peer ospf01 allowed-ips '0.0.0.0/0' + set interfaces wireguard wg01 peer ospf01 endpoint '10.1.1.100:12345' + set interfaces wireguard wg01 peer ospf01 pubkey 'NHI...=' + set interfaces wireguard wg01 port '12345' + set protocols ospfv3 parameters router-id 192.168.1.2 + set protocols ospfv3 area 0.0.0.0 interface 'wg01' + set protocols ospfv3 area 0.0.0.0 interface 'lo' + +**Status** + +.. code-block:: none + + vyos@ospf01:~$ sh ipv6 ospfv3 neighbor + Neighbor ID Pri DeadTime State/IfState Duration I/F[State] + 192.168.0.2 1 00:00:37 Full/PointToPoint 00:18:03 wg01[PointToPoint] + + vyos@ospf02# run sh ipv6 ospfv3 neighbor + Neighbor ID Pri DeadTime State/IfState Duration I/F[State] + 192.168.0.1 1 00:00:39 Full/PointToPoint 00:19:44 wg01[PointToPoint] + diff --git a/docs/configuration/protocols/ospfv3.rst b/docs/configuration/protocols/ospfv3.rst deleted file mode 100644 index f0e28983..00000000 --- a/docs/configuration/protocols/ospfv3.rst +++ /dev/null @@ -1,71 +0,0 @@ -OSPFv3 (IPv6) -############# - -A typical configuration using 2 nodes. - -**Node 1:** - -.. code-block:: none - - set protocols ospfv3 area 0.0.0.0 interface eth1 - set protocols ospfv3 area 0.0.0.0 range 2001:db8:1::/64 - set protocols ospfv3 parameters router-id 192.168.1.1 - set protocols ospfv3 redistribute connected - -**Node 2:** - -.. code-block:: none - - set protocols ospfv3 area 0.0.0.0 interface eth1 - set protocols ospfv3 area 0.0.0.0 range 2001:db8:2::/64 - set protocols ospfv3 parameters router-id 192.168.2.1 - set protocols ospfv3 redistribute connected - -.. note:: You can not easily redistribute IPv6 routes via OSPFv3 on a WireGuard - interface link. This requires you to configure link-local addresses manually - on the WireGuard interfaces, see :vytask:`T1483`. - -Example configuration for WireGuard interfaces: - -**Node 1** - -.. code-block:: none - - set interfaces wireguard wg01 address 'fe80::216:3eff:fe51:fd8c/64' - set interfaces wireguard wg01 address '192.168.0.1/24' - set interfaces wireguard wg01 peer ospf02 allowed-ips '::/0' - set interfaces wireguard wg01 peer ospf02 allowed-ips '0.0.0.0/0' - set interfaces wireguard wg01 peer ospf02 endpoint '10.1.1.101:12345' - set interfaces wireguard wg01 peer ospf02 pubkey 'ie3...=' - set interfaces wireguard wg01 port '12345' - set protocols ospfv3 parameters router-id 192.168.1.1 - set protocols ospfv3 area 0.0.0.0 interface 'wg01' - set protocols ospfv3 area 0.0.0.0 interface 'lo' - -**Node 2** - -.. code-block:: none - - set interfaces wireguard wg01 address 'fe80::216:3eff:fe0a:7ada/64' - set interfaces wireguard wg01 address '192.168.0.2/24' - set interfaces wireguard wg01 peer ospf01 allowed-ips '::/0' - set interfaces wireguard wg01 peer ospf01 allowed-ips '0.0.0.0/0' - set interfaces wireguard wg01 peer ospf01 endpoint '10.1.1.100:12345' - set interfaces wireguard wg01 peer ospf01 pubkey 'NHI...=' - set interfaces wireguard wg01 port '12345' - set protocols ospfv3 parameters router-id 192.168.1.2 - set protocols ospfv3 area 0.0.0.0 interface 'wg01' - set protocols ospfv3 area 0.0.0.0 interface 'lo' - -**Status** - -.. code-block:: none - - vyos@ospf01:~$ sh ipv6 ospfv3 neighbor - Neighbor ID Pri DeadTime State/IfState Duration I/F[State] - 192.168.0.2 1 00:00:37 Full/PointToPoint 00:18:03 wg01[PointToPoint] - - vyos@ospf02# run sh ipv6 ospfv3 neighbor - Neighbor ID Pri DeadTime State/IfState Duration I/F[State] - 192.168.0.1 1 00:00:39 Full/PointToPoint 00:19:44 wg01[PointToPoint] - |