diff options
Diffstat (limited to 'docs')
| -rw-r--r-- | docs/configuration/vpn/site2site_ipsec.rst | 129 |
1 files changed, 67 insertions, 62 deletions
diff --git a/docs/configuration/vpn/site2site_ipsec.rst b/docs/configuration/vpn/site2site_ipsec.rst index 8c0af774..23df1b76 100644 --- a/docs/configuration/vpn/site2site_ipsec.rst +++ b/docs/configuration/vpn/site2site_ipsec.rst @@ -10,8 +10,8 @@ connected/routed networks. To configure site-to-site connection you need to add peers with the ``set vpn ipsec site-to-site peer <name>`` command. -The peer name must be an alphanumeric and can have hypen or underscore as -special characters. It is purely informational. +The peer name must be an alphanumeric and can have hypen or underscore as +special characters. It is purely informational. Each site-to-site peer has the next options: @@ -20,11 +20,11 @@ Each site-to-site peer has the next options: * ``psk`` - Preshared secret key name: - * ``dhcp-interface`` - ID for authentication generated from DHCP address + * ``dhcp-interface`` - ID for authentication generated from DHCP address dynamically; - * ``id`` - static ID's for authentication. In general local and remote + * ``id`` - static ID's for authentication. In general local and remote address ``<x.x.x.x>``, ``<h:h:h:h:h:h:h:h>`` or ``%any``; - * ``secret`` - predefined shared secret. Used if configured mode + * ``secret`` - predefined shared secret. Used if configured mode ``pre-shared-secret``; @@ -110,7 +110,7 @@ Each site-to-site peer has the next options: * ``remote-address`` - remote IP address or hostname for IPSec connection. IPv4 or IPv6 address is used when a peer has a public static IP address. - Hostname is a DNS name which could be used when a peer has a public IP + Hostname is a DNS name which could be used when a peer has a public IP address and DNS name, but an IP address could be changed from time to time. * ``tunnel`` - define criteria for traffic to be matched for encrypting and send @@ -149,9 +149,9 @@ Each site-to-site peer has the next options: * ``esp-group`` - define ESP group for encrypt traffic, passed this VTI interface. -* ``virtual-address`` - Defines a virtual IP address which is requested by the - initiator and one or several IPv4 and/or IPv6 addresses are assigned from - multiple pools by the responder. +* ``virtual-address`` - Defines a virtual IP address which is requested by the + initiator and one or several IPv4 and/or IPv6 addresses are assigned from + multiple pools by the responder. Examples: ------------------ @@ -308,31 +308,35 @@ Imagine the following topology set interfaces dummy dum0 address '10.0.11.1/24' set interfaces vti vti10 address '10.0.0.2/31' - set vpn ipsec option disable-route-autoinstall - set vpn ipsec authentication psk OFFICE-B id '172.18.201.10' - set vpn ipsec authentication psk OFFICE-B id '172.18.202.10' - set vpn ipsec authentication psk OFFICE-B secret 'secretkey' + set vpn ipsec authentication psk peer_172-18-202-10 id '172.18.201.10' + set vpn ipsec authentication psk peer_172-18-202-10 id '172.18.202.10' + set vpn ipsec authentication psk peer_172-18-202-10 secret 'secretkey' set vpn ipsec esp-group ESP_DEFAULT lifetime '3600' set vpn ipsec esp-group ESP_DEFAULT mode 'tunnel' set vpn ipsec esp-group ESP_DEFAULT pfs 'dh-group19' set vpn ipsec esp-group ESP_DEFAULT proposal 10 encryption 'aes256gcm128' set vpn ipsec esp-group ESP_DEFAULT proposal 10 hash 'sha256' + set vpn ipsec ike-group IKEv2_DEFAULT close-action 'none' + set vpn ipsec ike-group IKEv2_DEFAULT dead-peer-detection action 'hold' + set vpn ipsec ike-group IKEv2_DEFAULT dead-peer-detection interval '30' + set vpn ipsec ike-group IKEv2_DEFAULT dead-peer-detection timeout '120' + set vpn ipsec ike-group IKEv2_DEFAULT disable-mobike set vpn ipsec ike-group IKEv2_DEFAULT key-exchange 'ikev2' set vpn ipsec ike-group IKEv2_DEFAULT lifetime '10800' - set vpn ipsec ike-group IKEv2_DEFAULT disable-mobike set vpn ipsec ike-group IKEv2_DEFAULT proposal 10 dh-group '19' set vpn ipsec ike-group IKEv2_DEFAULT proposal 10 encryption 'aes256gcm128' set vpn ipsec ike-group IKEv2_DEFAULT proposal 10 hash 'sha256' set vpn ipsec interface 'eth0.201' - set vpn ipsec site-to-site peer OFFICE-B authentication local-id '172.18.201.10' - set vpn ipsec site-to-site peer OFFICE-B authentication mode 'pre-shared-secret' - set vpn ipsec site-to-site peer OFFICE-B authentication remote-id '172.18.202.10' - set vpn ipsec site-to-site peer OFFICE-B connection-type 'respond' - set vpn ipsec site-to-site peer OFFICE-B ike-group 'IKEv2_DEFAULT' - set vpn ipsec site-to-site peer OFFICE-B local-address '172.18.201.10' - set vpn ipsec site-to-site peer OFFICE-B remote-address '172.18.202.10' - set vpn ipsec site-to-site peer OFFICE-B vti bind 'vti10' - set vpn ipsec site-to-site peer OFFICE-B vti esp-group 'ESP_DEFAULT' + set vpn ipsec site-to-site peer peer_172-18-202-10 authentication local-id '172.18.201.10' + set vpn ipsec site-to-site peer peer_172-18-202-10 authentication mode 'pre-shared-secret' + set vpn ipsec site-to-site peer peer_172-18-202-10 authentication remote-id '172.18.202.10' + set vpn ipsec site-to-site peer peer_172-18-202-10 connection-type 'initiate' + set vpn ipsec site-to-site peer peer_172-18-202-10 ike-group 'IKEv2_DEFAULT' + set vpn ipsec site-to-site peer peer_172-18-202-10 ikev2-reauth 'inherit' + set vpn ipsec site-to-site peer peer_172-18-202-10 local-address '172.18.201.10' + set vpn ipsec site-to-site peer peer_172-18-202-10 remote-address '172.18.202.10' + set vpn ipsec site-to-site peer peer_172-18-202-10 vti bind 'vti10' + set vpn ipsec site-to-site peer peer_172-18-202-10 vti esp-group 'ESP_DEFAULT' set protocols static interface-route 10.0.12.0/24 next-hop-interface vti10 @@ -344,34 +348,35 @@ Imagine the following topology set interfaces dummy dum0 address '10.0.12.1/24' set interfaces vti vti10 address '10.0.0.3/31' - set vpn ipsec option disable-route-autoinstall - set vpn ipsec authentication psk OFFICE-A id '172.18.201.10' - set vpn ipsec authentication psk OFFICE-A id '172.18.202.10' - set vpn ipsec authentication psk OFFICE-A secret 'secretkey' + set vpn ipsec authentication psk peer_172-18-201-10 id '172.18.202.10' + set vpn ipsec authentication psk peer_172-18-201-10 id '172.18.201.10' + set vpn ipsec authentication psk peer_172-18-201-10 secret 'secretkey' set vpn ipsec esp-group ESP_DEFAULT lifetime '3600' set vpn ipsec esp-group ESP_DEFAULT mode 'tunnel' set vpn ipsec esp-group ESP_DEFAULT pfs 'dh-group19' set vpn ipsec esp-group ESP_DEFAULT proposal 10 encryption 'aes256gcm128' set vpn ipsec esp-group ESP_DEFAULT proposal 10 hash 'sha256' - set vpn ipsec ike-group IKEv2_DEFAULT dead-peer-detection action 'restart' + set vpn ipsec ike-group IKEv2_DEFAULT close-action 'none' + set vpn ipsec ike-group IKEv2_DEFAULT dead-peer-detection action 'hold' set vpn ipsec ike-group IKEv2_DEFAULT dead-peer-detection interval '30' set vpn ipsec ike-group IKEv2_DEFAULT dead-peer-detection timeout '120' + set vpn ipsec ike-group IKEv2_DEFAULT disable-mobike set vpn ipsec ike-group IKEv2_DEFAULT key-exchange 'ikev2' set vpn ipsec ike-group IKEv2_DEFAULT lifetime '10800' - set vpn ipsec ike-group IKEv2_DEFAULT disable-mobike set vpn ipsec ike-group IKEv2_DEFAULT proposal 10 dh-group '19' set vpn ipsec ike-group IKEv2_DEFAULT proposal 10 encryption 'aes256gcm128' set vpn ipsec ike-group IKEv2_DEFAULT proposal 10 hash 'sha256' set vpn ipsec interface 'eth0.202' - set vpn ipsec site-to-site peer OFFICE-A authentication local-id '172.18.202.10' - set vpn ipsec site-to-site peer OFFICE-A authentication mode 'pre-shared-secret' - set vpn ipsec site-to-site peer OFFICE-A authentication remote-id '172.18.201.10' - set vpn ipsec site-to-site peer OFFICE-A connection-type 'initiate' - set vpn ipsec site-to-site peer OFFICE-A ike-group 'IKEv2_DEFAULT' - set vpn ipsec site-to-site peer OFFICE-A local-address '172.18.202.10' - set vpn ipsec site-to-site peer OFFICE-A remote-address '172.18.201.10' - set vpn ipsec site-to-site peer OFFICE-A vti bind 'vti10' - set vpn ipsec site-to-site peer OFFICE-A vti esp-group 'ESP_DEFAULT' + set vpn ipsec site-to-site peer peer_172-18-201-10 authentication local-id '172.18.202.10' + set vpn ipsec site-to-site peer peer_172-18-201-10 authentication mode 'pre-shared-secret' + set vpn ipsec site-to-site peer peer_172-18-201-10 authentication remote-id '172.18.201.10' + set vpn ipsec site-to-site peer peer_172-18-201-10 connection-type 'initiate' + set vpn ipsec site-to-site peer peer_172-18-201-10 ike-group 'IKEv2_DEFAULT' + set vpn ipsec site-to-site peer peer_172-18-201-10 ikev2-reauth 'inherit' + set vpn ipsec site-to-site peer peer_172-18-201-10 local-address '172.18.202.10' + set vpn ipsec site-to-site peer peer_172-18-201-10 remote-address '172.18.201.10' + set vpn ipsec site-to-site peer peer_172-18-201-10 vti bind 'vti10' + set vpn ipsec site-to-site peer peer_172-18-201-10 vti esp-group 'ESP_DEFAULT' set protocols static interface-route 10.0.11.0/24 next-hop-interface vti10 @@ -379,44 +384,44 @@ Key Parameters: * ``authentication local-id/remote-id`` - IKE identification is used for validation of VPN peer devices during IKE negotiation. If you do not configure - local/remote-identity, the device uses the IPv4 or IPv6 address that + local/remote-identity, the device uses the IPv4 or IPv6 address that corresponds to the local/remote peer by default. - In certain network setups (like ipsec interface with dynamic address, or - behind the NAT ), the IKE ID received from the peer does not match the IKE - gateway configured on the device. This can lead to a Phase 1 validation + In certain network setups (like ipsec interface with dynamic address, or + behind the NAT ), the IKE ID received from the peer does not match the IKE + gateway configured on the device. This can lead to a Phase 1 validation failure. - So, make sure to configure the local/remote id explicitly and ensure that the + So, make sure to configure the local/remote id explicitly and ensure that the IKE ID is the same as the remote-identity configured on the peer device. * ``disable-route-autoinstall`` - This option when configured disables the routes installed in the default table 220 for site-to-site ipsec. It is mostly used with VTI configuration. -* ``dead-peer-detection action = clear | hold | restart`` - R_U_THERE - notification messages(IKEv1) or empty INFORMATIONAL messages (IKEv2) - are periodically sent in order to check the liveliness of the IPsec peer. The - values clear, hold, and restart all activate DPD and determine the action to +* ``dead-peer-detection action = clear | hold | restart`` - R_U_THERE + notification messages(IKEv1) or empty INFORMATIONAL messages (IKEv2) + are periodically sent in order to check the liveliness of the IPsec peer. The + values clear, hold, and restart all activate DPD and determine the action to perform on a timeout. - With ``clear`` the connection is closed with no further actions taken. - ``hold`` installs a trap policy, which will catch matching traffic and tries - to re-negotiate the connection on demand. - ``restart`` will immediately trigger an attempt to re-negotiate the + With ``clear`` the connection is closed with no further actions taken. + ``hold`` installs a trap policy, which will catch matching traffic and tries + to re-negotiate the connection on demand. + ``restart`` will immediately trigger an attempt to re-negotiate the connection. -* ``close-action = none | clear | hold | restart`` - defines the action to take - if the remote peer unexpectedly closes a CHILD_SA (see above for meaning of +* ``close-action = none | clear | hold | restart`` - defines the action to take + if the remote peer unexpectedly closes a CHILD_SA (see above for meaning of values). A closeaction should not be used if the peer uses reauthentication or uniqueids. - - When the close-action option is set on the peers, the connection-type + + When the close-action option is set on the peers, the connection-type of each peer has to considered carefully. For example, if the option is set - on both peers, then both would attempt to initiate and hold open multiple - copies of each child SA. This might lead to instability of the device or - cpu/memory utilization. - - Below flow-chart could be a quick reference for the close-action - combination depending on how the peer is configured. + on both peers, then both would attempt to initiate and hold open multiple + copies of each child SA. This might lead to instability of the device or + cpu/memory utilization. + + Below flow-chart could be a quick reference for the close-action + combination depending on how the peer is configured. .. figure:: /_static/images/IPSec_close_action_settings.jpg - + Similar combinations are applicable for the dead-peer-detection. |