From f95ed893ca04a00eafdb665947fdc2c38d4ab397 Mon Sep 17 00:00:00 2001 From: Eron Lloyd Date: Sat, 19 Sep 2020 12:04:04 -0400 Subject: Update quick-start.rst Adding a few minor edits to clean up the descriptions and add some consistency to them. --- docs/quick-start.rst | 52 ++++++++++++++++++++++++++++++++++++---------------- 1 file changed, 36 insertions(+), 16 deletions(-) (limited to 'docs/quick-start.rst') diff --git a/docs/quick-start.rst b/docs/quick-start.rst index 19ee9f6e..550bfd77 100644 --- a/docs/quick-start.rst +++ b/docs/quick-start.rst @@ -4,7 +4,7 @@ Quick Start ########### -This chapter will guide you on how to get up to speed using your new VyOS +This chapter will guide you on how to get up to speed quickly using your new VyOS system. It will show you a very basic configuration example that will provide a :ref:`nat` gateway for a device with two network interfaces (`eth0` and `eth1`). @@ -14,6 +14,10 @@ a :ref:`nat` gateway for a device with two network interfaces (`eth0` and Configuration Mode ################## +By default, VyOS is in operational mode, and the command prompt displays a `$`. To configure VyOS, +you will need to enter configuration mode, resulting in the command prompt displaying a `#`, as +demonstrated below: + .. code-block:: none vyos@vyos$ configure @@ -22,13 +26,13 @@ Configuration Mode Commit and Save ################ -After every configuration change you need to apply the changes by using the +After every configuration change, you need to apply the changes by using the following command: .. code-block:: none commit -Once your configuration works as expected you can save it permanently. +Once your configuration works as expected, you can save it permanently by using the following command: .. code-block:: none @@ -37,9 +41,9 @@ Once your configuration works as expected you can save it permanently. Interface Configuration ####################### -* Your outside/WAN interface will be `eth0`, it receives it's interface address - be means of DHCP. -* Your internal/LAN interface is `eth1`. It uses a fixed IP address of +* Your outside/WAN interface will be `eth0`. It will receive its interface address + via DHCP. +* Your internal/LAN interface will be `eth1`. It will use a static IP address of `192.168.0.1/24`. After switching to :ref:`quick-start-configuration-mode` issue the following @@ -69,14 +73,17 @@ on specific addresses only. Configure DHCP/DNS Servers ########################## -* Provide DHCP service on your internal/LAN network where VyOS will act - as the default gateway and DNS server. -* Client IP addresses are assigned from the range ``192.168.0.9 - - 192.168.0.254`` +The following settings will configure DHCP and DNS services on your internal/LAN network, +where VyOS will act as the default gateway and DNS server. + +* The default gateway and DNS recursor address will be `192.168.0.1/24` +* The address range `192.168.0.2/24 - 192.168.0.8/24` will be reserved for static assignments +* DHCP clients will be assigned IP addresses within the range of `192.168.0.9 - 192.168.0.254` + and have a domain name of `internal-network` * DHCP leases will hold for one day (86400 seconds) -* VyOS will server as full DNS recursor - no need to bother the Google or - Cloudflare DNS servers (good for privacy) -* Only clients from your internal/LAN network can use the DNS resolver +* VyOS will serve as a full DNS recursor, replacing the need to utilize Google, + Cloudflare, or other public DNS servers (which is good for privacy) +* Only hosts from your internal/LAN network can use the DNS recursor .. code-block:: none @@ -95,7 +102,8 @@ Configure DHCP/DNS Servers NAT ### -* Configure :ref:`source-nat` for our internal/LAN network +The following settings will configure :ref:`source-nat` rules for our internal/LAN network, allowing +hosts to communicate through the outside/WAN network via IP masquerade. .. code-block:: none @@ -188,11 +196,23 @@ Set up :ref:`ssh_key_based_authentication`: Finally, try and SSH into the VyOS install as your new user. Once you have confirmed that your new user can access your router without a password, delete -the original ``vyos`` user and probably disable password authentication for -:ref:`ssh` at all: +the original ``vyos`` user and completely disable password authentication for +:ref:`ssh`: .. code-block:: none delete system login user vyos set service ssh disable-password-authentication +As above, commit your changes, save the configuration, and exit configuration mode: + +.. code-block:: none + + vyos@vyos# commit + vyos@vyos# save + Saving configuration to '/config/config.boot'... + Done + vyos@vyos# exit + vyos@vyos$ + +You now should have a simple yet secure and functioning router to experiment with further. Enjoy! -- cgit v1.2.3