From 6aa3cbb611f74bdf8e44d5527f5138f3122a7497 Mon Sep 17 00:00:00 2001 From: Christian Poessinger Date: Wed, 27 Nov 2019 17:20:36 +0100 Subject: Refactor "code-block:: sh" to "code-block:: console" This will add proper new-lines into the rendered PDF. Before if it has been a long line, not all content was preserved in the PDF. --- docs/services/pppoe-server.rst | 30 +++++++++++++++--------------- 1 file changed, 15 insertions(+), 15 deletions(-) (limited to 'docs/services/pppoe-server.rst') diff --git a/docs/services/pppoe-server.rst b/docs/services/pppoe-server.rst index 03e14971..3f42ceab 100644 --- a/docs/services/pppoe-server.rst +++ b/docs/services/pppoe-server.rst @@ -15,7 +15,7 @@ The example below uses ACN as access-concentrator name, assigns an address from the pool 10.1.1.100-111, terminates at the local endpoint 10.1.1.1 and serves requests only on eth1. -.. code-block:: sh +.. code-block:: console set service pppoe-server access-concentrator 'ACN' set service pppoe-server authentication local-users username foo password 'bar' @@ -30,7 +30,7 @@ serves requests only on eth1. Connections can be locally checked via the command -.. code-block:: sh +.. code-block:: console show pppoe-server sessions ifname | username | ip | calling-sid | rate-limit | state | uptime | rx-bytes | tx-bytes @@ -48,7 +48,7 @@ If the CIDR notation is used, multiple subnets can be setup which are used seque **Client IP address via IP range definition** -.. code-block:: sh +.. code-block:: console set service pppoe-server client-ip-pool start '10.1.1.100' set service pppoe-server client-ip-pool stop '10.1.1.111' @@ -56,7 +56,7 @@ If the CIDR notation is used, multiple subnets can be setup which are used seque **Client IP subnets via CIDR notation** -.. code-block:: sh +.. code-block:: console set service pppoe-server client-ip-pool subnet '10.1.1.0/24' set service pppoe-server client-ip-pool subnet '10.1.2.0/24' @@ -70,7 +70,7 @@ To use a radius server, you need to switch to authentication mode radius and of course need to specify an IP for the server. You can have multiple RADIUS server configured, if you wish to achieve redundancy. -.. code-block:: sh +.. code-block:: console set service pppoe-server access-concentrator 'ACN' set service pppoe-server authentication mode 'radius' @@ -84,7 +84,7 @@ RADIUS provides the IP addresses in the example above via Framed-IP-Address. For remotely disconnect sessions and change some authentication parameters you can configure dae-server -.. code-block:: sh +.. code-block:: console set service pppoe-server authentication radius-settings dae-server ip-address '10.1.1.2' set service pppoe-server authentication radius-settings dae-server port '3799' @@ -92,20 +92,20 @@ For remotely disconnect sessions and change some authentication parameters you c Example, from radius-server send command for disconnect client with username test -.. code-block:: sh +.. code-block:: console root@radius-server:~# echo "User-Name=test" | radclient -x 10.1.1.2:3799 disconnect secret123 You can also use another attributes for identify client for disconnect, like Framed-IP-Address, Acct-Session-Id, etc. Result commands appears in log -.. code-block:: sh +.. code-block:: console show log | match Disconnect* Example for changing rate-limit via RADIUS CoA -.. code-block:: sh +.. code-block:: console echo "User-Name=test,Filter-Id=5000/4000" | radclient 10.1.1.2:3799 coa secret123 @@ -119,7 +119,7 @@ Automatic VLAN creation VLAN's can be created by accel-ppp on the fly if via the use of the kernel module vlan_mon, which is monitoring incoming vlans and creates the necessary VLAN if required and allowed. VyOS supports the use of either VLAN ID's or entire ranges, both values can be defined at the same time for an interface. -.. code-block:: sh +.. code-block:: console set service pppoe-server interface eth3 vlan-id 100 set service pppoe-server interface eth3 vlan-id 200 @@ -141,7 +141,7 @@ Bandwidth Shaping for local users The rate-limit is set in kbit/sec. -.. code-block:: sh +.. code-block:: console set service pppoe-server access-concentrator 'ACN' set service pppoe-server authentication local-users username foo password 'bar' @@ -158,7 +158,7 @@ The rate-limit is set in kbit/sec. Once the user is connected, the user session is using the set limits and can be displayed via 'show pppoe-server sessions'. -.. code-block:: sh +.. code-block:: console show pppoe-server sessions ifname | username | ip | calling-sid | rate-limit | state | uptime | rx-bytes | tx-bytes @@ -175,7 +175,7 @@ Filter-Id=2000/3000 (means 2000Kbit down-stream rate and 3000Kbit up-stream rate The command below enables it, assuming the RADIUS connection has been setup and is working. -.. code-block:: sh +.. code-block:: console set service pppoe-server authentication radius-settings rate-limit enable @@ -191,7 +191,7 @@ Dual-stack provisioning with IPv6 PD via pppoe The example below covers a dual-stack configuration via pppoe-server. -.. code-block:: sh +.. code-block:: console set service pppoe-server authentication local-users username test password 'test' set service pppoe-server authentication mode 'local' @@ -207,7 +207,7 @@ The example below covers a dual-stack configuration via pppoe-server. The client, once successfully authenticated, will receive an IPv4 and an IPv6 /64 address, to terminate the pppoe endpoint on the client side and a /56 subnet for the clients internal use. -.. code-block:: sh +.. code-block:: console vyos@pppoe-server:~$ sh pppoe-server sessions ifname | username | ip | ip6 | ip6-dp | calling-sid | rate-limit | state | uptime | rx-bytes | tx-bytes -- cgit v1.2.3