.. _syslog: ###### Syslog ###### Per default VyOSs has minimal syslog logging enabled which is stored and rotated locally. Errors will be always logged to a local file, which includes `local7` error messages, emergency messages will be sent to the console, too. To configure syslog, you need to switch into configuration mode. Logging ======= Syslog supports logging to multiple targets, those targets could be a plain file on your VyOS installation itself, a serial console or a remote syslog server which is reached via :abbr:`IP (Internet Protocol)` UDP/TCP. Console ------- .. cfgcmd:: set system syslog console facility level Log syslog messages to ``/dev/console``, for an explanation on :ref:`syslog_facilities` keywords and :ref:`syslog_severity_level` keywords see tables below. .. _custom-file: Custom File ----------- .. cfgcmd:: set system syslog file facility level Log syslog messages to file specified via ``, for an explanation on :ref:`syslog_facilities` keywords and :ref:`syslog_severity_level` keywords see tables below. .. cfgcmd:: set system syslog file archive size Syslog will write `` kilobytes into the file specified by ``. After this limit has been reached, the custom file is "rotated" by logrotate and a new custom file is created. .. cfgcmd:: set system syslog file archive file Syslog uses logrotate to rotate logiles after a number of gives bytes. We keep as many as `` rotated file before they are deleted on the system. Remote Host ----------- Logging to a remote host leaves the local logging configuration intact, it can be configured in parallel to a custom file or console logging. You can log to multiple hosts at the same time, using either TCP or UDP. The default is sending the messages via port 514/UDP. .. cfgcmd:: set system syslog host
facility level Log syslog messages to remote host specified by `
`. The address can be specified by either FQDN or IP address. For an explanation on :ref:`syslog_facilities` keywords and :ref:`syslog_severity_level` keywords see tables below. .. cfgcmd:: set system syslog host
facility protocol Configure protocol used for communication to remote syslog host. This can be either UDP or TCP. .. cfgcmd:: set system syslog vrf Specify name of the :abbr:`VRF (Virtual Routing and Forwarding)` instance. Local User Account ------------------ .. cfgcmd:: set system syslog user facility level If logging to a local user account is configured, all defined log messages are display on the console if the local user is logged in, if the user is not logged in, no messages are being displayed. For an explanation on :ref:`syslog_facilities` keywords and :ref:`syslog_severity_level` keywords see tables below. .. _syslog_facilities: Facilities ========== List of facilities used by syslog. Most facilities names are self explanatory. Facilities local0 - local7 common usage is f.e. as network logs facilities for nodes and network equipment. Generally it depends on the situation how to classify logs and put them to facilities. See facilities more as a tool rather than a directive to follow. Facilities can be adjusted to meet the needs of the user: +----------+----------+----------------------------------------------------+ | Facility | Keyword | Description | | Code | | | +==========+==========+====================================================+ | | all | All facilities | +----------+----------+----------------------------------------------------+ | 0 | kern | Kernel messages | +----------+----------+----------------------------------------------------+ | 1 | user | User-level messages | +----------+----------+----------------------------------------------------+ | 2 | mail | Mail system | +----------+----------+----------------------------------------------------+ | 3 | daemon | System daemons | +----------+----------+----------------------------------------------------+ | 4 | auth | Security/authentication messages | +----------+----------+----------------------------------------------------+ | 5 | syslog | Messages generated internally by syslogd | +----------+----------+----------------------------------------------------+ | 6 | lpr | Line printer subsystem | +----------+----------+----------------------------------------------------+ | 7 | news | Network news subsystem | +----------+----------+----------------------------------------------------+ | 8 | uucp | UUCP subsystem | +----------+----------+----------------------------------------------------+ | 9 | cron | Clock daemon | +----------+----------+----------------------------------------------------+ | 10 | security | Security/authentication messages | +----------+----------+----------------------------------------------------+ | 11 | ftp | FTP daemon | +----------+----------+----------------------------------------------------+ | 12 | ntp | NTP subsystem | +----------+----------+----------------------------------------------------+ | 13 | logaudit | Log audit | +----------+----------+----------------------------------------------------+ | 14 | logalert | Log alert | +----------+----------+----------------------------------------------------+ | 15 | clock | clock daemon (note 2) | +----------+----------+----------------------------------------------------+ | 16 | local0 | local use 0 (local0) | +----------+----------+----------------------------------------------------+ | 17 | local1 | local use 1 (local1) | +----------+----------+----------------------------------------------------+ | 18 | local2 | local use 2 (local2) | +----------+----------+----------------------------------------------------+ | 19 | local3 | local use 3 (local3) | +----------+----------+----------------------------------------------------+ | 20 | local4 | local use 4 (local4) | +----------+----------+----------------------------------------------------+ | 21 | local5 | local use 5 (local5) | +----------+----------+----------------------------------------------------+ | 22 | local6 | use 6 (local6) | +----------+----------+----------------------------------------------------+ | 23 | local7 | local use 7 (local7) | +----------+----------+----------------------------------------------------+ .. _syslog_severity_level: Severity Level ============== +-------+---------------+---------+-------------------------------------------+ | Value | Severity | Keyword | Description | +=======+===============+=========+===========================================+ | | | all | Log everything | +-------+---------------+---------+-------------------------------------------+ | 0 | Emergency | emerg | System is unusable - a panic condition | +-------+---------------+---------+-------------------------------------------+ | 1 | Alert | alert | Action must be taken immediately - A | | | | | condition that should be corrected | | | | | immediately, such as a corrupted system | | | | | database. | +-------+---------------+---------+-------------------------------------------+ | 2 | Critical | crit | Critical conditions - e.g. hard drive | | | | | errors. | +-------+---------------+---------+-------------------------------------------+ | 3 | Error | err | Error conditions | +-------+---------------+---------+-------------------------------------------+ | 4 | Warning | warning | Warning conditions | +-------+---------------+---------+-------------------------------------------+ | 5 | Notice | notice | Normal but significant conditions - | | | | | conditions that are not error conditions, | | | | | but that may require special handling. | +-------+---------------+---------+-------------------------------------------+ | 6 | Informational | info | Informational messages | +-------+---------------+---------+-------------------------------------------+ | 7 | Debug | debug | Debug-level messages - Messages that | | | | | contain information normally of use only | | | | | when debugging a program. | +-------+---------------+---------+-------------------------------------------+ Display Logs ============ .. opcmd:: show log [all | authorization | cluster | conntrack-sync | ...] Display log files of given category on the console. Use tab completion to get a list of available categories. Thos categories could be: all, authorization, cluster, conntrack-sync, dhcp, directory, dns, file, firewall, https, image lldp, nat, openvpn, snmp, tail, vpn, vrrp If no option is specified, this defaults to `all`. .. opcmd:: show log image [all | authorization | directory | file | tail ] Log messages from a specified image can be displayed on the console. Details of allowed parameters: .. list-table:: :widths: 25 75 :header-rows: 0 * - all - Display contents of all master log files of the specified image * - authorization - Display all authorization attempts of the specified image * - directory - Display list of all user-defined log files of the specified image * - file - Display contents of a specified user-defined log file of the specified image * - tail - Display last lines of the system log of the specified image * - - Number of lines to be displayed, default 10 When no options/parameters are used, the contents of the main syslog file are displayed. .. hint:: Use ``show log | strip-private`` if you want to hide private data when sharing your logs. Delete Logs =========== .. opcmd:: delete log file Deletes the specified user-defined file in the /var/log/user directory Note that deleting the log file does not stop the system from logging events. If you use this command while the system is logging events, old log events will be deleted, but events after the delete operation will be recorded in the new file. To delete the file altogether, first delete logging to the file using system syslog :ref:`custom-file` command, and then delete the file.