.. _interfaces-addresses: Interface Addresses ------------------- Each interface can be configured with a description and address. Interface addresses might be: * Static IPv4 `address 172.16.51.129/24` * Static IPv6 `address 2001:db8:1::ffff/64` * DHCP IPv4 `address dhcp` * DHCP IPv6 `address dhcpv6` An interface description is assigned using the following command: .. code-block:: sh set interfaces ethernet eth0 description 'OUTSIDE' IPv4 ^^^^ Static Address ************** This method is supported on all interfaces, apart from OpenVPN that uses different syntax and wireless modems that are always autoconfigured through PPP. The command is `set interfaces $type $name address $address`. Examples: .. code-block:: sh set interfaces ethernet eth0 address 192.0.2.1/24 set interfaces tunnel tun0 address 10.0.0.1/30 set interfaces bridge br0 address 203.0.113.45/26 set interfaces ethernet eth0 vif 30 address 192.0.30.254/24 DHCP **** This method is supported on all physical interfaces, and those that are directly connected to a physical interface (ethernet, VLAN, bridge, bond, pseudo-ethernet, wireless). The command is `set interfaces $type $name address dhcp`. Examples: .. code-block:: sh set interfaces ethernet eth0 vif 90 address dhcp set interfaces bridge br0 address dhcp IPv6 ^^^^ Static Address ************** This method is supported on all interfaces, apart from OpenVPN that uses different syntax and wireless modems that are always autoconfigured through PPP. Static IPv6 addresses are supported on all interfaces except :ref:`interfaces-tunnel`. The command is `set interfaces $type $name address $address`. Examples: .. code-block:: sh set interfaces ethernet eth0 address 2001:db8:100::ffff/64 set interfaces tunnel tun0 address 2001:db8::1/64 set interfaces bridge br0 address 2001:db8:200::1/64 set interfaces ethernet eth0 vif 30 address 2001:db8:3::ffff/64 DHCP **** This method is supported on all physical interfaces, and those that are directly connected to a physical interface (ethernet, VLAN, bridge, bond, pseudo-ethernet, wireless). The command is `set interfaces $type $name address dhcpv6`. Examples: .. code-block:: sh set interfaces bonding bond1 address dhcpv6 set interfaces bridge br0 vif 56 address dhcpv6 Autoconfiguration (SLAAC) ************************* SLAAC is specified in RFC4862_. This method is supported on all physical interfaces, and those that are directly connected to a physical interface (ethernet, VLAN, bridge, bond, pseudo-ethernet, wireless). The command is `set interfaces $type $name ipv6 address autoconf`. Examples: .. code-block:: sh set interfaces ethernet eth0 vif 90 ipv6 address autoconf set interfaces bridge br0 ipv6 address autoconf .. note:: This method automatically disables IPv6 traffic forwarding on the interface in question. EUI-64 ****** EUI-64 (64-Bit Extended Unique Identifier) as specified in RFC4291_. IPv6 addresses in /64 networks can be automatically generated from the prefix and MAC address, if you specify the prefix. The command is `set interfaces $type $name ipv6 address eui64 $prefix`. Examples: .. code-block:: sh set interfaces bridge br0 ipv6 address eui64 2001:db8:beef::/64 set interfaces pseudo-ethernet peth0 ipv6 address eui64 2001:db8:aa::/64 Router Advertisements ********************* Router advertisements are described in `RFC4861 section 4.2`_. They are part of what is known as SLAAC (Stateless Address Autoconfiguration). To enable or disable, use: .. code-block:: sh set interfaces ipv6 router-advert send-advert To set the options described in "Router Advertisement Message Format": .. code-block:: sh vyos@vyos# set interfaces ipv6 router-advert Possible completions: cur-hop-limit Value to be placed in the "Current Hop Limit" field in RAs default-lifetime Value to be placed in "Router Lifetime" field in RAs default-preference Default router preference link-mtu Value of link MTU to place in RAs managed-flag Value for "managed address configuration" flag in RAs max-interval Maximum interval between unsolicited multicast RAs min-interval Minimum interval between unsolicited multicast RAs + name-server IPv6 address of a Recursive DNS Server other-config-flag Value to be placed in the "other configuration" flag in RAs +> prefix IPv6 prefix to be advertised in Router Advertisements (RAs) reachable-time Value to be placed in "Reachable Time" field in RAs retrans-timer Value to place in "Retrans Timer" field in RAs. send-advert Enable/disable sending RAs **Prefix Information** Prefix information is described in `RFC4861 section 4.6.2`_ .. code-block:: sh vyos@vyos# set interfaces ipv6 router-advert prefix Possible completions: autonomous-flag Whether prefix can be used for address auto-configuration on-link-flag Flag that prefix can be used for on-link determination preferred-lifetime Time in seconds that the prefix will remain preferred valid-lifetime Time in seconds that the prefix will remain valid **Receiving Router Advertisements** To receive and accept RAs on an interface, you need to enable it with the following configuration command .. code-block:: sh vyos@vyos# set system sysctl custom net.ipv6.conf..accept_ra value 2 .. _`RFC4861 section 4.6.2`: https://tools.ietf.org/html/rfc4861#section-4.6.2 .. _`RFC4861 section 4.2`: https://tools.ietf.org/html/rfc4861#section-4.2 .. _RFC4862: https://tools.ietf.org/html/rfc4862 .. _RFC4291: http://tools.ietf.org/html/rfc4291#section-2.5.1