blob: c456a58edd30d5271fae78a3f73273f2dbc304b2 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
|
.. include:: ../_include/need_improvement.txt
.. _l2tpv3-interface:
######
L2TPv3
######
L2TPv3 is a pseudowire protocol, you can read more about on `Wikipedia L2TPv3`_
or in :rfc:`3921`
L2TPv3 can transport any traffic including ethernet frames. L2TPv2 is limited
to PPP.
Configuration
#############
Common interface configuration
------------------------------
.. cmdinclude:: ../_include/interface-common-without-dhcp.txt
:var0: l2tpv3
:var1: l2tpeth0
Over IP
^^^^^^^
.. code-block:: none
# show interfaces l2tpv3
l2tpv3 l2tpeth10 {
address 192.168.37.1/27
encapsulation ip
local-ip 192.0.2.1
peer-session-id 100
peer-tunnel-id 200
remote-ip 203.0.113.24
session-id 100
tunnel-id 200
}
Inverse configuration has to be applied to the remote side.
Over UDP
^^^^^^^^
UDP mode works better with NAT:
* Set local-ip to your local IP (LAN).
* Add a forwarding rule matching UDP port on your internet router.
.. code-block:: none
# show interfaces l2tpv3
l2tpv3 l2tpeth10 {
address 192.168.37.1/27
destination-port 9001
encapsulation udp
local-ip 192.0.2.1
peer-session-id 100
peer-tunnel-id 200
remote-ip 203.0.113.24
session-id 100
source-port 9000
tunnel-id 200
}
To create more than one tunnel, use distinct UDP ports.
Over IPSec, L2 VPN (bridge)
^^^^^^^^^^^^^^^^^^^^^^^^^^^
This is the LAN extension use case. The eth0 port of the distant VPN peers
will be directly connected like if there was a switch between them.
IPSec:
.. code-block:: none
set vpn ipsec ipsec-interfaces <VPN-interface>
set vpn ipsec esp-group test-ESP-1 compression 'disable'
set vpn ipsec esp-group test-ESP-1 lifetime '3600'
set vpn ipsec esp-group test-ESP-1 mode 'transport'
set vpn ipsec esp-group test-ESP-1 pfs 'enable'
set vpn ipsec esp-group test-ESP-1 proposal 1 encryption 'aes128'
set vpn ipsec esp-group test-ESP-1 proposal 1 hash 'sha1'
set vpn ipsec ike-group test-IKE-1 ikev2-reauth 'no'
set vpn ipsec ike-group test-IKE-1 key-exchange 'ikev1'
set vpn ipsec ike-group test-IKE-1 lifetime '3600'
set vpn ipsec ike-group test-IKE-1 proposal 1 dh-group '5'
set vpn ipsec ike-group test-IKE-1 proposal 1 encryption 'aes128'
set vpn ipsec ike-group test-IKE-1 proposal 1 hash 'sha1'
set vpn ipsec site-to-site peer <peer-ip> authentication mode 'pre-shared-secret'
set vpn ipsec site-to-site peer <peer-ip> authentication pre-shared-secret <pre-shared-key>
set vpn ipsec site-to-site peer <peer-ip> connection-type 'initiate'
set vpn ipsec site-to-site peer <peer-ip> ike-group 'test-IKE-1'
set vpn ipsec site-to-site peer <peer-ip> ikev2-reauth 'inherit'
set vpn ipsec site-to-site peer <peer-ip> local-address <local-ip>
set vpn ipsec site-to-site peer <peer-ip> tunnel 1 allow-nat-networks 'disable'
set vpn ipsec site-to-site peer <peer-ip> tunnel 1 allow-public-networks 'disable'
set vpn ipsec site-to-site peer <peer-ip> tunnel 1 esp-group 'test-ESP-1'
set vpn ipsec site-to-site peer <peer-ip> tunnel 1 protocol 'l2tp'
Bridge:
.. code-block:: none
set interfaces bridge br0 description 'L2 VPN Bridge'
# remote side in this example:
# set interfaces bridge br0 address '172.16.30.18/30'
set interfaces bridge br0 address '172.16.30.17/30'
set interfaces bridge br0 member interface eth0
set interfaces ethernet eth0 description 'L2 VPN Physical port'
L2TPv3:
.. code-block:: none
set interfaces bridge br0 member interface 'l2tpeth0'
set interfaces l2tpv3 l2tpeth0 description 'L2 VPN Tunnel'
set interfaces l2tpv3 l2tpeth0 destination-port '5000'
set interfaces l2tpv3 l2tpeth0 encapsulation 'ip'
set interfaces l2tpv3 l2tpeth0 local-ip <local-ip>
set interfaces l2tpv3 l2tpeth0 mtu '1500'
set interfaces l2tpv3 l2tpeth0 peer-session-id '110'
set interfaces l2tpv3 l2tpeth0 peer-tunnel-id '10'
set interfaces l2tpv3 l2tpeth0 remote-ip <peer-ip>
set interfaces l2tpv3 l2tpeth0 session-id '110'
set interfaces l2tpv3 l2tpeth0 source-port '5000'
set interfaces l2tpv3 l2tpeth0 tunnel-id '10'
.. _`Wikipedia L2TPv3`: https://en.wikipedia.org/wiki/L2TPv3
|
