path: root/docs/interfaces/wireless.rst

.. _wireless-interface:

###################
Wireless LAN (WiFi)
###################

:abbr:`WLAN (Wireless LAN)` interface provide 802.11 (a/b/g/n/ac) wireless
support (commonly referred to as Wi-Fi) by means of compatible hardware. If your
hardware supports it, VyOS supports multiple logical wireless interfaces per
physical device.

There are three modes of operation for a wireless interface:

* :abbr:`WAP (Wireless Access-Point)` provides network access to connecting
  stations if the physical hardware supports acting as a WAP

* A station acts as a Wi-Fi client accessing the network through an available
  WAP

* Monitor, the system passively monitors any kind of wireless traffic

If the system detects an unconfigured wireless device, it will be automatically
added the configuration tree, specifying any detected settings (for example,
its MAC address) and configured to run in monitor mode.

*************
Configuration
*************

Common interface configuration
==============================

.. cmdinclude:: ../_include/interface-common-with-dhcp.txt
   :var0: wireless
   :var1: wlan0

Wireless options
================

.. cfgcmd:: set interfaces wireless <interface> channel <number>

  Channel number (IEEE 802.11), for 2.4Ghz (802.11 b/g/n) channels range from
  1-14. On 5Ghz (802.11 a/h/j/n/ac) channels available are 0, 34 to 173

.. cfgcmd:: set interfaces wireless <interface> country-code <cc>

  Country code (ISO/IEC 3166-1). Used to set regulatory domain. Set as needed
  to indicate country in which device is operating. This can limit available
  channels and transmit power.

  .. note:: This option is mandatory in Access-Point mode.

.. cfgcmd:: set interfaces wireless <interface> disable-broadcast-ssid

  Send empty SSID in beacons and ignore probe request frames that do not specify
  full SSID, i.e., require stations to know SSID.

.. cfgcmd:: set interfaces wireless <interface> expunge-failing-stations

  Disassociate stations based on excessive transmission failures or other
  indications of connection loss.

  This depends on the driver capabilities and may not be available with all
  drivers.

.. cfgcmd:: set interfaces wireless <interface> isolate-stations

  Client isolation can be used to prevent low-level bridging of frames between
  associated stations in the BSS.

  By default, this bridging is allowed.

.. cfgcmd:: set interfaces wireless <interface> max-stations

  Maximum number of stations allowed in station table. New stations will be
  rejected after the station table is full. IEEE 802.11 has a limit of 2007
  different association IDs, so this number should not be larger than that.

  This defaults to 2007.

.. cfgcmd:: set interfaces wireless <interface> mgmt-frame-protection

  Management Frame Protection (MFP) according to IEEE 802.11w

.. cfgcmd:: set interfaces wireless <interface> mode <a | b | g | n | ac>

  Operation mode of wireless radio.

  * ``a`` - 802.11a - 54 Mbits/sec
  * ``b`` - 802.11b - 11 Mbits/sec
  * ``g`` - 802.11g - 54 Mbits/sec (default)
  * ``n`` - 802.11n - 600 Mbits/sec
  * ``ac`` - 802.11ac - 1300 Mbits/sec

.. cfgcmd:: set interfaces wireless <interface> physical-device <device>

  Wireless hardware device used as underlay radio.

  This defaults to phy0.

.. cfgcmd:: set interfaces wireless <interface> reduce-transmit-power <number>

  Add Power Constraint element to Beacon and Probe Response frames.

  This option adds Power Constraint element when applicable and Country element
  is added. Power Constraint element is required by Transmit Power Control.

  Valid values are 0..255.

.. cfgcmd:: set interfaces wireless <interface> ssid <ssid>

  SSID to be used in IEEE 802.11 management frames

.. cfgcmd:: set interfaces wireless <interface> type <access-point | station | monitor>

  Wireless device type for this interface

  * ``access-point`` - Access-point forwards packets between other nodes
  * ``station`` - Connects to another access point
  * ``monitor`` - Passively monitor all packets on the frequency/channel

PPDU
----

.. cfgcmd:: set interfaces wireless <interface> capabilities require-ht

.. cfgcmd:: set interfaces wireless <interface> capabilities require-hvt

HT (High Throughput) capabilities (802.11n)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

.. cfgcmd:: set interfaces wireless <interface> capabilities ht 40mhz-incapable

  Device is incapable of 40 MHz, do not advertise. This sets ``[40-INTOLERANT]``

.. cfgcmd:: set interfaces wireless <interface> capabilities ht auto-powersave

  WMM-PS Unscheduled Automatic Power Save Delivery [U-APSD]

.. cfgcmd:: set interfaces wireless <interface> capabilities ht channel-set-width <ht20 | ht40+ | ht40->

  Supported channel width set.

  * ``ht40-`` - Both 20 MHz and 40 MHz with secondary channel below the primary
    channel
  * ``ht40+`` - Both 20 MHz and 40 MHz with secondary channel above the primary
    channel

  .. note:: There are limits on which channels can be used with HT40- and HT40+.
    Following table shows the channels that may be available for HT40- and HT40+
    use per IEEE 802.11n Annex J:

    Depending on the location, not all of these channels may be available for use!

    .. code-block:: none

      freq		HT40-		HT40+
      2.4 GHz		5-13		1-7 (1-9 in Europe/Japan)
      5 GHz		40,48,56,64	36,44,52,60

  .. note:: 40 MHz channels may switch their primary and secondary channels if
    needed or creation of 40 MHz channel maybe rejected based on overlapping
    BSSes. These changes are done automatically when hostapd is setting up the
    40 MHz channel.

.. cfgcmd:: set interfaces wireless <interface> capabilities ht delayed-block-ack

  Enable HT-delayed Block Ack ``[DELAYED-BA]``

.. cfgcmd:: set interfaces wireless <interface> capabilities ht dsss-cck-40

  DSSS/CCK Mode in 40 MHz, this sets ``[DSSS_CCK-40]``

.. cfgcmd:: set interfaces wireless <interface> capabilities ht greenfield

  This enables the greenfield option which sets the ``[GF]`` option

.. cfgcmd:: set interfaces wireless <interface> capabilities ht ldpc

  Enable LDPC coding capability

.. cfgcmd:: set interfaces wireless <interface> capabilities ht lsig-protection

  Enable L-SIG TXOP protection capability

.. cfgcmd:: set interfaces wireless <interface> capabilities ht max-amsdu <3839 | 7935>

  Maximum A-MSDU length 3839 (default) or 7935 octets

.. cfgcmd:: set interfaces wireless <interface> capabilities ht short-gi <20 | 40>

  Short GI capabilities for 20 and 40 MHz

.. cfgcmd:: set interfaces wireless <interface> capabilities ht smps <static | dynamic>

  Spatial Multiplexing Power Save (SMPS) settings

.. cfgcmd:: set interfaces wireless <interface> capabilities ht stbc rx <num>

  Enable receiving PPDU using STBC (Space Time Block Coding)

.. cfgcmd:: set interfaces wireless <interface> capabilities ht stbc tx

  Enable sending PPDU using STBC (Space Time Block Coding)

VHT (Very High Throughput) capabilities (802.11ac)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

.. cfgcmd:: set interfaces wireless <interface> capabilities vht antenna-count

  Number of antennas on this card

.. cfgcmd:: set interfaces wireless <interface> capabilities vht antenna-pattern-fixed

  Set if antenna pattern does not change during the lifetime of an association

.. cfgcmd:: set interfaces wireless <interface> capabilities vht beamform
  <single-user-beamformer | single-user-beamformee | multi-user-beamformer |
  multi-user-beamformee>

  Beamforming capabilities:

  * ``single-user-beamformer`` - Support for operation as single user beamformer
  * ``single-user-beamformee`` - Support for operation as single user beamformee
  * ``multi-user-beamformer`` - Support for operation as single user beamformer
  * ``multi-user-beamformee`` - Support for operation as single user beamformer

.. cfgcmd:: set interfaces wireless <interface> capabilities vht center-channel-freq <freq-1 | freq-2>

  VHT operating channel center frequency - center freq 1 (for use with 80, 80+80 and 160 modes)

  VHT operating channel center frequency - center freq 2 (for use with the 80+80 mode)

.. cfgcmd:: set interfaces wireless <interface> capabilities vht channel-set-width <0 | 1 | 2 | 3>

   * ``0`` - 20 or 40 MHz channel width (default)
   * ``1`` - 80 MHz channel width
   * ``2`` - 160 MHz channel width
   * ``3`` - 80+80 MHz channel width

.. cfgcmd:: set interfaces wireless <interface> capabilities vht ldpc

  Enable LDPC (Low Density Parity Check) coding capability

.. cfgcmd:: set interfaces wireless <interface> capabilities vht link-adaptation

  VHT link adaptation capabilities

.. cfgcmd:: set interfaces wireless <interface> capabilities vht max-mpdu <value>

  Increase Maximum MPDU length to 7991 or 11454 octets (default 3895 octets)

.. cfgcmd:: set interfaces wireless <interface> capabilities vht max-mpdu-exp <value>

  Set the maximum length of A-MPDU pre-EOF padding that the station can receive

.. cfgcmd:: set interfaces wireless <interface> capabilities vht short-gi <80 | 160>

  Short GI capabilities

.. cfgcmd:: set interfaces wireless <interface> capabilities vht stbc rx <num>

  Enable receiving PPDU using STBC (Space Time Block Coding)

.. cfgcmd:: set interfaces wireless <interface> capabilities vht stbc tx

  Enable sending PPDU using STBC (Space Time Block Coding)

.. cfgcmd:: set interfaces wireless <interface> capabilities vht tx-powersave

  Enable VHT TXOP Power Save Mode

.. cfgcmd:: set interfaces wireless <interface> capabilities vht vht-cf

  Station supports receiving VHT variant HT Control field


Wireless options (Station/Client)
=================================

The example creates a wireless station (commonly referred to as Wi-Fi client)
that accesses the network through the WAP defined in the above example. The
default physical device (``phy0``) is used.

.. code-block:: none

  set interfaces wireless wlan0 type station
  set interfaces wireless wlan0 address dhcp
  set interfaces wireless wlan0 ssid Test
  set interfaces wireless wlan0 security wpa

Resulting in

.. code-block:: none

  interfaces {
    [...]
    wireless wlan0 {
      address dhcp
      security {
        wpa {
          passphrase "12345678"
        }
      }
      ssid TEST
      type station
    }

Security
========

:abbr:`WPA (Wi-Fi Protected Access)` and WPA2 Enterprise in combination with
802.1x based authentication can be used to authenticate users or computers
in a domain.

The wireless client (supplicant) authenticates against the RADIUS server
(authentication server) using an :abbr:`EAP (Extensible Authentication
Protocol)`  method configured on the RADIUS server. The WAP (also referred
to as authenticator) role is to send all authentication messages between the
supplicant and the configured authentication server, thus the RADIUS server
is responsible for authenticating the users.

The WAP in this example has the following characteristics:

* IP address ``192.168.2.1/24``
* Network ID (SSID) ``Enterprise-TEST``
* WPA passphrase ``12345678``
* Use 802.11n protocol
* Wireless channel ``1``
* RADIUS server at ``192.168.3.10`` with shared-secret ``VyOSPassword``

.. code-block:: none

  set interfaces wireless wlan0 address '192.168.2.1/24'
  set interfaces wireless wlan0 type access-point
  set interfaces wireless wlan0 channel 1
  set interfaces wireless wlan0 mode n
  set interfaces wireless wlan0 ssid 'TEST'
  set interfaces wireless wlan0 security wpa mode wpa2
  set interfaces wireless wlan0 security wpa cipher CCMP
  set interfaces wireless wlan0 security wpa radius server 192.168.3.10 key 'VyOSPassword'
  set interfaces wireless wlan0 security wpa radius server 192.168.3.10 port 1812

Resulting in

.. code-block:: none

  interfaces {
    [...]
    wireless wlan0 {
          address 192.168.2.1/24
          channel 1
          mode n
          security {
              wpa {
                  cipher CCMP
                  mode wpa2
                  radius {
                      server 192.168.3.10 {
                          key 'VyOSPassword'
                          port 1812
                      }
                  }
              }
          }
          ssid "Enterprise-TEST"
          type access-point
      }
  }
  system {
    [...]
    wifi-regulatory-domain DE
  }


*********
Operation
*********

.. opcmd:: show interfaces wireless info

Use this command to view operational status and wireless-specific information
about all wireless interfaces.

.. code-block:: none

  vyos@vyos:~$ show interfaces wireless info
  Interface  Type          SSID                         Channel
  wlan0      access-point  VyOS-TEST-0                        1

.. opcmd:: show interfaces wireless detail

Use this command to view operational status and detailes wireless-specific
information about all wireless interfaces.

.. code-block:: none

  vyos@vyos:~$ show interfaces wireless detail
  wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
      link/ether XX:XX:XX:XX:XX:c3 brd XX:XX:XX:XX:XX:ff
      inet xxx.xxx.99.254/24 scope global wlan0
         valid_lft forever preferred_lft forever
      inet6 fe80::xxxx:xxxx:fe54:2fc3/64 scope link
         valid_lft forever preferred_lft forever

      RX:  bytes    packets     errors    dropped    overrun      mcast
           66072        282          0          0          0          0
      TX:  bytes    packets     errors    dropped    carrier collisions
           83413        430          0          0          0          0

  wlan1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
      link/ether XX:XX:XX:XX:XX:c3 brd XX:XX:XX:XX:XX:ff
      inet xxx.xxx.100.254/24 scope global wlan0
         valid_lft forever preferred_lft forever
      inet6 fe80::xxxx:xxxx:ffff:2ed3/64 scope link
         valid_lft forever preferred_lft forever

      RX:  bytes    packets     errors    dropped    overrun      mcast
           166072      5282          0          0          0          0
      TX:  bytes    packets     errors    dropped    carrier collisions
           183413      5430          0          0          0          0

.. opcmd:: show interfaces wireless <wlanX>

This command shows both status and statistics on the specified wireless interface.
The wireless interface identifier can range from wlan0 to wlan999.

.. code-block:: none

  vyos@vyos:~$ show interfaces wireless wlan0
  wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
      link/ether XX:XX:XX:XX:XX:c3 brd XX:XX:XX:XX:XX:ff
      inet xxx.xxx.99.254/24 scope global wlan0
         valid_lft forever preferred_lft forever
      inet6 fe80::xxxx:xxxx:fe54:2fc3/64 scope link
         valid_lft forever preferred_lft forever

      RX:  bytes    packets     errors    dropped    overrun      mcast
           66072        282          0          0          0          0
      TX:  bytes    packets     errors    dropped    carrier collisions
           83413        430          0          0          0          0


.. opcmd:: show interfaces wireless <wlanX> brief

This command gives a brief status overview of a specified wireless interface.
The wireless interface identifier can range from wlan0 to wlan999.

.. code-block:: none

  vyos@vyos:~$ show interfaces wireless wlan0 brief
  Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
  Interface        IP Address                        S/L  Description
  ---------        ----------                        ---  -----------
  wlan0            192.168.2.254/24                    u/u


.. opcmd:: show interfaces wireless <wlanX> queue

Use this command to view wireless interface queue information.
The wireless interface identifier can range from wlan0 to wlan999.

.. code-block:: none

  vyos@vyos:~$ show interfaces wireless wlan0 queue
  qdisc pfifo_fast 0: root bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
   Sent 810323 bytes 6016 pkt (dropped 0, overlimits 0 requeues 0)
   rate 0bit 0pps backlog 0b 0p requeues 0


.. opcmd:: show interfaces wireless <wlanX> scan

This command is used to retrieve information about WAP within the range of your
wireless interface. This command is useful on wireless interfaces configured
in station mode.

.. note:: Scanning is not supported on all wireless drivers and wireless
   hardware. Refer to your driver and wireless hardware documentation for
   further details.

.. code-block:: none

  vyos@vyos:~$ show interfaces wireless wlan0 scan
  Address            SSID                          Channel  Signal (dbm)
  00:53:3b:88:6e:d8  WLAN-576405                         1  -64.00
  00:53:3b:88:6e:da  Telekom_FON                         1  -64.00
  00:53:00:f2:c2:a4  BabyView_F2C2A4                     6  -60.00
  00:53:3b:88:6e:d6  Telekom_FON                       100  -72.00
  00:53:3b:88:6e:d4  WLAN-576405                       100  -71.00
  00:53:44:a4:96:ec  KabelBox-4DC8                      56  -81.00
  00:53:d9:7a:67:c2  WLAN-741980                         1  -75.00
  00:53:7c:99:ce:76  Vodafone Homespot                   1  -86.00
  00:53:44:a4:97:21  KabelBox-4DC8                       1  -78.00
  00:53:44:a4:97:21  Vodafone Hotspot                    1  -79.00
  00:53:44:a4:97:21  Vodafone Homespot                   1  -79.00
  00:53:86:40:30:da  Telekom_FON                         1  -86.00
  00:53:7c:99:ce:76  Vodafone Hotspot                    1  -86.00
  00:53:44:46:d2:0b  Vodafone Hotspot                    1  -87.00


********
Examples
********

The following example creates a WAP. When configuring multiple WAP interfaces,
you must specify unique IP addresses, channels, Network IDs commonly referred
to as :abbr:`SSID (Service Set Identifier)`, and MAC addresses.

The WAP in this example has the following characteristics:

* IP address ``192.168.2.1/24``
* Network ID (SSID) ``TEST``
* WPA passphrase ``12345678``
* Use 802.11n protocol
* Wireless channel ``1``

.. code-block:: none

  set interfaces wireless wlan0 address '192.168.2.1/24'
  set interfaces wireless wlan0 type access-point
  set interfaces wireless wlan0 channel 1
  set interfaces wireless wlan0 mode n
  set interfaces wireless wlan0 ssid 'TEST'
  set interfaces wireless wlan0 security wpa mode wpa2
  set interfaces wireless wlan0 security wpa cipher CCMP
  set interfaces wireless wlan0 security wpa passphrase '12345678'

Resulting in

.. code-block:: none

  interfaces {
    [...]
    wireless wlan0 {
          address 192.168.2.1/24
          channel 1
          mode n
          security {
              wpa {
                  cipher CCMP
                  mode wpa2
                  passphrase "12345678"
              }
          }
          ssid "TEST"
          type access-point
      }
  }
  system {
    [...]
    wifi-regulatory-domain DE
  }

To get it to work as a access point with this configuration you will need
to set up a DHCP server to work with that network. You can - of course - also
bridge the Wireless interface with any configured bridge
(:ref:`bridge-interface`) on the system.