arrange firewall

2 files changed, 790 insertions, 0 deletions

diff --git a/docs/configuration/firewall/index.rst b/docs/configuration/firewall/index.rst
new file mode 100644
index 00000000..870e9a08
--- /dev/null
+++ b/docs/configuration/firewall/index.rst
@@ -0,0 +1,767 @@
+.. _firewall:
+
+Firewall
+========
+
+Overview
+--------
+
+VyOS makes use of Linux `netfilter <https://netfilter.org/>`_ for packet
+filtering.
+
+The firewall supports the creation of groups for ports, addresses, and
+networks (implemented using netfilter ipset) and the option of interface
+or zone based firewall policy.
+
+.. note:: **Important note on usage of terms:** 
+   The firewall makes use of the terms `in`, `out`, and `local`
+   for firewall policy. Users experienced with netfilter often confuse
+   `in` to be a reference to the `INPUT` chain, and `out` the `OUTPUT`
+   chain from netfilter. This is not the case. These instead indicate
+   the use of the `FORWARD` chain and either the input or output
+   interface. The `INPUT` chain, which is used for local traffic to the
+   OS, is a reference to as `local` with respect to its input interface.
+
+
+Global settings
+---------------
+
+Some firewall settings are global and have a affect on the whole system.
+
+.. cfgcmd:: set firewall all-ping [enable | disable]
+
+   By default, when VyOS receives an ICMP echo request packet destined for
+   itself, it will answer with an ICMP echo reply, unless you avoid it
+   through its firewall.
+
+   With the firewall you can set rules to accept, drop or reject ICMP in,
+   out or local traffic. You can also use the general **firewall all-ping**
+   command. This command affects only to LOCAL (packets destined for your
+   VyOS system), not to IN or OUT traffic.
+
+   .. note:: **firewall all-ping** affects only to LOCAL and it always
+      behaves in the most restrictive way
+
+   .. code-block:: none
+
+      set firewall all-ping enable
+
+   When the command above is set, VyOS will answer every ICMP echo request
+   addressed to itself, but that will only happen if no other rule is
+   applied dropping or rejecting local echo requests. In case of conflict,
+   VyOS will not answer ICMP echo requests.
+
+   .. code-block:: none
+
+      set firewall all-ping disable
+
+   When the command above is set, VyOS will answer no ICMP echo request
+   addressed to itself at all, no matter where it comes from or whether
+   more specific rules are being applied to accept them.
+
+.. cfgcmd:: set firewall broadcast-ping [enable | disable]
+
+   This setting enable or disable the response of icmp broadcast
+   messages. The following system parameter will be altered:
+
+   * ``net.ipv4.icmp_echo_ignore_broadcasts``
+
+.. cfgcmd:: set firewall ip-src-route [enable | disable]
+.. cfgcmd:: set firewall ipv6-src-route [enable | disable]
+
+   This setting handle if VyOS accept packets with a source route
+   option. The following system parameter will be altered:
+
+   * ``net.ipv4.conf.all.accept_source_route``
+   * ``net.ipv6.conf.all.accept_source_route``
+
+.. cfgcmd:: set firewall receive-redirects [enable | disable]
+.. cfgcmd:: set firewall ipv6-receive-redirects [enable | disable]
+
+   enable or disable of ICMPv4 or ICMPv6 redirect messages accepted
+   by VyOS. The following system parameter will be altered:
+
+   * ``net.ipv4.conf.all.accept_redirects``
+   * ``net.ipv6.conf.all.accept_redirects``
+
+.. cfgcmd:: set firewall send-redirects [enable | disable]
+
+   enable or disable of ICMPv4 redirect messages send by VyOS 
+   The following system parameter will be altered:
+
+   * ``net.ipv4.conf.all.send_redirects``
+
+.. cfgcmd:: set firewall log-martians [enable | disable]
+
+   enable or disable the logging of martian IPv4 packets. 
+   The following system parameter will be altered:
+
+   * ``net.ipv4.conf.all.log_martians``
+
+.. cfgcmd:: set firewall source-validation [strict | loose | disable]
+
+   Set the IPv4 source validation mode. 
+   The following system parameter will be altered:
+
+   * ``net.ipv4.conf.all.rp_filter``
+
+.. cfgcmd:: set firewall syn-cookies [enable | disable]
+
+   Enable or Disable if VyOS use IPv4 TCP SYN Cookies. 
+   The following system parameter will be altered:
+
+   * ``net.ipv4.tcp_syncookies``
+
+.. cfgcmd:: set firewall twa-hazards-protection [enable | disable]
+
+   Enable or Disable VyOS to be :rfc:`1337` conform. 
+   The following system parameter will be altered:
+
+   * ``net.ipv4.tcp_rfc1337``
+
+.. cfgcmd:: set firewall state-policy established action [accept | drop |
+   reject]
+
+.. cfgcmd:: set firewall state-policy established log enable
+
+   Set the global setting for a astablished connections.
+
+.. cfgcmd:: set firewall state-policy invalid action [accept | drop | reject]
+
+.. cfgcmd:: set firewall state-policy invalid log enable
+
+   Set the global setting for invalid packets. 
+
+.. cfgcmd:: set firewall state-policy related action [accept | drop | reject]
+
+.. cfgcmd:: set firewall state-policy related log enable
+
+   Set the global setting for related connections.
+
+
+Groups
+------
+
+Firewall groups represent collections of IP addresses, networks, or
+ports. Once created, a group can be referenced by firewall rules as
+either a source or destination. Members can be added or removed from a
+group without changes to, or the need to reload, individual firewall
+rules.
+
+.. note:: Groups can also be referenced by NAT configuration.
+
+Groups need to have unique names. Even though some contain IPv4
+addresses and others contain IPv6 addresses, they still need to have
+unique names, so you may want to append "-v4" or "-v6" to your group
+names.
+
+
+Address Groups
+**************
+
+In a **address group** a single IP adresses or IP address ranges are
+definded.
+
+.. cfgcmd::  set firewall group address-group <name> address [address |
+   address range]
+.. cfgcmd::  set firewall group ipv6-address-group <name> address <address>
+
+   Define a IPv4 or a IPv6 address group
+
+   .. code-block:: none
+
+      set firewall group address-group ADR-INSIDE-v4 address 192.168.0.1
+      set firewall group address-group ADR-INSIDE-v4 address 10.0.0.1-10.0.0.8
+      set firewall group ipv6-address-group ADR-INSIDE-v6 address 2001:db8::1
+
+.. cfgcmd::  set firewall group address-group <name> description <text>
+.. cfgcmd::  set firewall group ipv6-address-group <name> description <text>
+
+   Provide a IPv4 or IPv6 address group description
+
+
+Network Groups
+**************
+
+While **network groups** accept IP networks in CIDR notation, specific
+IP addresses can be added as a 32-bit prefix. If you foresee the need
+to add a mix of addresses and networks, the network group is
+recommended.
+
+.. cfgcmd::  set firewall group network-group <name> network <CIDR>
+.. cfgcmd::  set firewall group ipv6-network-group <name> network <CIDR>
+
+   Define a IPv4 or IPv6 Network group.
+
+   .. code-block:: none
+
+      set firewall group network-group NET-INSIDE-v4 network 192.168.0.0/24
+      set firewall group network-group NET-INSIDE-v4 network 192.168.1.0/24
+      set firewall group ipv6-network-group NET-INSIDE-v6 network 2001:db8::/64
+
+.. cfgcmd::  set firewall group network-group <name> description <text>
+.. cfgcmd::  set firewall group ipv6-network-group <name> description <text>
+
+   Provide a IPv4 or IPv6 network group description.
+      
+
+Port Groups
+***********
+
+A **port group** represents only port numbers, not the protocol. Port
+groups can be referenced for either TCP or UDP. It is recommended that
+TCP and UDP groups are created separately to avoid accidentally
+filtering unnecessary ports. Ranges of ports can be specified by using
+`-`.
+
+.. cfgcmd:: set firewall group port-group <name> port
+   [portname | portnumber | startport-endport]
+
+   Define a port group. A port name are any name defined in
+   /etc/services. e.g.: http
+
+   .. code-block:: none
+
+      set firewall group port-group PORT-TCP-SERVER1 port http
+      set firewall group port-group PORT-TCP-SERVER1 port 443
+      set firewall group port-group PORT-TCP-SERVER1 port 5000-5010
+
+.. cfgcmd:: set firewall group port-group <name> description <text>
+
+   Provide a port group description.
+
+
+Rule-Sets
+----------
+
+A rule-set is a named collection of firewall rules that can be applied
+to an interface or zone. Each rule is numbered, has an action to apply
+if the rule is matched, and the ability to specify the criteria to
+match. Data packets go through the rules from 1 - 9999, at the first match
+the action of the rule will executed.
+
+.. cfgcmd:: set firewall name <name> description <text>
+.. cfgcmd:: set firewall ipv6-name <name> description <text>
+
+   Provide a rule-set description.
+
+.. cfgcmd:: set firewall name <name> default-action [drop | reject | accept]
+.. cfgcmd:: set firewall ipv6-name <name> default-action [drop | reject |
+   accept]
+
+   This set the default action of the rule-set if no rule matched a paket
+   criteria.
+
+.. cfgcmd:: set firewall name <name> enable-default-log
+.. cfgcmd:: set firewall ipv6-name <name> enable-default-log
+
+   Use this command to enable the logging of the default action.
+
+.. cfgcmd:: set firewall name <name> rule <1-9999> action [drop | reject |
+   accept]
+.. cfgcmd:: set firewall ipv6-name <name> rule <1-9999> action [drop | reject |
+   accept]
+
+   This required setting define the action of the current rule.
+
+.. cfgcmd:: set firewall name <name> rule <1-9999> description <text>
+.. cfgcmd:: set firewall ipv6-name <name> rule <1-9999> description <text>
+
+   Provide a description for each rule.
+
+.. cfgcmd:: set firewall name <name> rule <1-9999> log [disable | enable]
+.. cfgcmd:: set firewall ipv6-name <name> rule <1-9999> log [disable | enable]
+
+   Enable or disable logging for the matched packet.
+
+.. cfgcmd:: set firewall name <name> rule <1-9999> disable
+.. cfgcmd:: set firewall ipv6-name <name> rule <1-9999> disable
+
+   If you want to disable a rule but let it in the configuration.
+
+Matching criteria
+*****************
+
+There are a lot of matching criteria gainst which the package can be tested.
+
+
+.. cfgcmd:: set firewall name <name> rule <1-9999> source address 
+   [address | addressrange | CIDR]
+.. cfgcmd:: set firewall name <name> rule <1-9999> destination address
+   [address | addressrange | CIDR]
+.. cfgcmd:: set firewall ipv6-name <name> rule <1-9999> source address
+   [address | addressrange | CIDR]
+.. cfgcmd:: set firewall ipv6-name <name> rule <1-9999> destination address
+   [address | addressrange | CIDR]
+
+   This is similiar to the network groups part, but here you are able to negate
+   the matching addresses.
+
+   .. code-block:: none
+
+      set firewall name WAN-IN-v4 rule 100 source address 192.0.2.10-192.0.2.11
+      # with a '!' the rule match everything except the specified subnet
+      set fitewall name WAN-IN-v4 rule 101 source address !203.0.113.0/24
+      set firewall ipv6-name WAN-IN-v6 rule 100 source address 2001:db8::202
+
+
+.. cfgcmd:: set firewall name <name> rule <1-9999> source mac-address 
+   <mac-address>
+.. cfgcmd:: set firewall ipv6-name <name> rule <1-9999> source mac-address 
+   <mac-address>
+
+   Only in the source criteria you can specify a mac-address
+
+   .. code-block:: none
+
+      set firewall name LAN-IN-v4 rule 100 source mac-address 00:53:00:11:22:33 
+      set firewall name LAN-IN-v4 rule 101 source mac-address !00:53:00:aa:12:34
+
+.. cfgcmd:: set firewall name <name> rule <1-9999> source port
+   [1-65535 | portname | start-end]
+.. cfgcmd:: set firewall name <name> rule <1-9999> destination port
+   [1-65535 | portname | start-end]
+.. cfgcmd:: set firewall ipv6-name <name> rule <1-9999> source port
+   [1-65535 | portname | start-end]
+.. cfgcmd:: set firewall ipv6-name <name> rule <1-9999> destination port
+   [1-65535 | portname | start-end]
+
+   A port can be set with a portnumber or a name which is here
+   defined: ``/etc/services``.
+
+   .. code-block:: none
+
+      set firewall name WAN-IN-v4 rule 10 source port '22'
+      set firewall name WAN-IN-v4 rule 11 source port '!http'
+      set firewall name WAN-IN-v4 rule 12 source port 'https'
+
+   Multiple source ports can be specified as a comma-separated list.
+   The whole list can also be "negated" using '!'. For example:
+   
+   .. code-block:: none
+
+      set firewall ipv6-name WAN-IN-v6 rule 10 source port '!22,https,3333-3338'
+
+.. cfgcmd:: set firewall name <name> rule <1-9999> source group
+   address-group <name>
+.. cfgcmd:: set firewall name <name> rule <1-9999> destination group
+   address-group <name>
+.. cfgcmd:: set firewall ipv6-name <name> rule <1-9999> source group
+   address-group <name>
+.. cfgcmd:: set firewall ipv6-name <name> rule <1-9999> destination group
+   address-group <name>
+
+   Use a specific address-group
+
+.. cfgcmd:: set firewall name <name> rule <1-9999> source group
+   network-group <name>
+.. cfgcmd:: set firewall name <name> rule <1-9999> destination group
+   network-group <name>
+.. cfgcmd:: set firewall ipv6-name <name> rule <1-9999> source group
+   network-group <name>
+.. cfgcmd:: set firewall ipv6-name <name> rule <1-9999> destination group
+   network-group <name>
+
+   Use a specific network-group
+
+.. cfgcmd:: set firewall name <name> rule <1-9999> source group
+   port-group <name>
+.. cfgcmd:: set firewall name <name> rule <1-9999> destination group
+   port-group <name>
+.. cfgcmd:: set firewall ipv6-name <name> rule <1-9999> source group
+   port-group <name>
+.. cfgcmd:: set firewall ipv6-name <name> rule <1-9999> destination group
+   port-group <name>
+
+   Use a specific port-group
+
+.. cfgcmd:: set firewall name <name> rule <1-9999> protocol [<text> |
+   <0-255> | all | tcp_udp]
+.. cfgcmd:: set firewall ipv6-name <name> rule <1-9999> protocol [<text> |
+   <0-255> | all | tcp_udp]
+
+   Match a protocol criteria. A protocol number or a name which is here
+   defined: ``/etc/protocols``. 
+   Special names are ``all`` for all protocols and ``tcp_udp`` for tcp and upd
+   based pakets. The ``!`` negate the selected protocol.
+
+   .. code-block:: none
+
+      set firewall name WAN-IN-v4 rule 10 protocol tcp_udp
+      set firewall name WAN-IN-v4 rule 11 protocol !tcp_udp
+      set firewall ipv6-name WAN-IN-v6 rule 10 protocol tcp
+
+.. cfgcmd:: set firewall name <name> rule <1-9999> tcp flags <text>
+.. cfgcmd:: set firewall ipv6-name <name> rule <1-9999> tcp flags <text>
+
+   Allowed values fpr TCP flags: ``SYN``, ``ACK``, ``FIN``, ``RST``, ``URG``,
+   ``PSH``, ``ALL`` When specifying more than one flag, flags should be comma
+   separated. The ``!`` negate the selected protocol.
+   
+   .. code-block:: none
+
+      set firewall name WAN-IN-v4 rule 10 tcp flags 'ACK'
+      set firewall name WAN-IN-v4 rule 12 tcp flags 'SYN'
+      set firewall name WAN-IN-v4 rule 13 tcp flags 'SYN,!ACK,!FIN,!RST'
+
+.. cfgcmd:: set firewall name <name> rule <1-9999> state [established |
+   invalid | new | related] [enable | disable ]
+.. cfgcmd:: set firewall ipv6-name <name> rule <1-9999> state [established |
+   invalid | new | related] [enable | disable ]
+
+   Match against the state of a packet.
+
+
+Applying a Rule-Set to an Interface
+-----------------------------------
+
+A Rule-Set can be appliend to every inteface:
+
+* ``in``: Ruleset for forwarded packets on inbound interface
+* ``out``: Ruleset for forwarded packets on outbound interface
+* ``local``: Ruleset for packets destined for this router
+
+.. cfgcmd:: set interface ethernet <ethN> firewall [in | out | local] 
+   [name | ipv6-name] <rule-set>
+
+   Here are some examples for applying a rule-set to an interface
+
+   .. code-block:: none
+
+      set interface ethernet eth1 vif 100 firewall in name LANv4-IN
+      set interface ethernet eth1 vif 100 firewall out name LANv4-OUT
+      set interface bonding bond0 firewall in name LANv4-IN
+      set interfaces openvpn vtun1 firewall in name Lanv4-IN
+
+   .. note::
+      As you can see in the example here, you can assign the same rule-set to
+      several interfaces. An interface can only have one rule-set per chain.
+
+
+Zone-based Firewall Policy
+--------------------------
+
+As an alternative to applying policy to an interface directly, a
+zone-based firewall can be created to simplify configuration when
+multiple interfaces belong to the same security zone. Instead of
+applying rulesets to interfaces, they are applied to source
+zone-destination zone pairs.
+
+An basic introduction to zone-based firewalls can be found `here
+<https://support.vyos.io/en/kb/articles/a-primer-to-zone-based-firewall>`_,
+and an example at :ref:`examples-zone-policy`.
+
+Define a Zone
+*************
+
+To define a zone setup either one with interfaces or a local zone.
+
+.. cfgcmd:: set zone-policy zone <name> interface <interfacenames>
+
+   Set a interfaces to a zone. A zone can have multiple interfaces.
+   But a interface can only be member in one zone.
+
+.. cfgcmd:: set zone-policy zone <name> local-zone
+
+   Define the Zone as a local zone. A local zone have no interfaces and
+   will be applied to the router itself.
+
+.. cfgcmd:: set zone-policy zone <name> default-action [drop | reject]
+
+   Change the default-action with this setting.
+
+.. cfgcmd:: set zone-policy zone <name> description
+
+   Set a meaningful description.
+
+
+Applying a Rule-Set to a Zone
+*****************************
+
+Before you are able to apply a rule-set to a zone you have to create the zones 
+first. 
+
+.. cfgcmd::  set zone-policy zone <name> from <name> firewall name
+   <rule-set>
+.. cfgcmd::  set zone-policy zone <name> from <name> firewall ipv6-name
+   <rule-set>
+
+   You apply a rule-set always to a zone from a other zone, it is recommended
+   to create one rule-set for each zone pair.
+
+   .. code-block:: none
+
+      set zone-policy zone DMZ from LAN firewall name LANv4-to-DMZv4
+      set zone-policy zone LAN from DMZ firewall name DMZv4-to-LANv4
+
+
+Operation-mode Firewall
+-----------------------
+
+Rule-set overview
+*****************
+
+.. opcmd:: show firewall
+
+   This will show you a basic firewall overview
+
+   .. code-block:: none
+
+      vyos@vyos:~$ show firewall
+
+      ------------------------
+      Firewall Global Settings
+      ------------------------
+
+      Firewall state-policy for all IPv4 and Ipv6 traffic
+
+      state           action   log
+      -----           ------   ---
+      invalid         accept   disabled
+      established     accept   disabled
+      related         accept   disabled
+
+      -----------------------------
+      Rulesets Information
+      -----------------------------
+      --------------------------------------------------------------------------
+      IPv4 Firewall "DMZv4-1-IN":
+
+      Active on (eth0,IN)
+
+      rule  action   proto     packets  bytes
+      ----  ------   -----     -------  -----
+      10    accept   icmp      0        0
+      condition - saddr 10.1.0.0/24 daddr 0.0.0.0/0 LOG enabled
+
+      10000 drop     all       0        0
+      condition - saddr 0.0.0.0/0 daddr 0.0.0.0/0 LOG enabled
+
+      --------------------------------------------------------------------------
+      IPv4 Firewall "DMZv4-1-OUT":
+
+      Active on (eth0,OUT)
+
+      rule  action   proto     packets  bytes
+      ----  ------   -----     -------  -----
+      10    accept   tcp_udp   1        60
+      condition - saddr 0.0.0.0/0 daddr 0.0.0.0/0 match-DST-PORT-GROUP DMZ-Ports /*
+                  DMZv4-1-OUT-10 */LOG enabled
+
+      11    accept   icmp      1        84
+      condition - saddr 0.0.0.0/0 daddr 0.0.0.0/0 /* DMZv4-1-OUT-11 */LOG enabled
+
+      10000 drop     all       6        360
+      condition - saddr 0.0.0.0/0 daddr 0.0.0.0/0 LOG enabled
+
+      --------------------------------------------------------------------------
+      IPv4 Firewall "LANv4-IN":
+
+      Inactive - Not applied to any interfaces or zones.
+
+      rule  action   proto     packets  bytes
+      ----  ------   -----     -------  -----
+      10    accept   all       0        0
+      condition - saddr 0.0.0.0/0 daddr 0.0.0.0/0 /* LANv4-IN-10 */
+
+      10000 drop     all       0        0
+      condition - saddr 0.0.0.0/0 daddr 0.0.0.0/0
+
+.. opcmd:: show firewall summary
+
+   This will show you a summary about rule-sets and groups
+
+   .. code-block:: none
+
+      vyos@vyos:~$ show firewall summary
+
+      ------------------------
+      Firewall Global Settings
+      ------------------------
+
+      Firewall state-policy for all IPv4 and Ipv6 traffic
+
+      state           action   log
+      -----           ------   ---
+      invalid         accept   disabled
+      related         accept   disabled
+      established     accept   disabled
+
+      ------------------------
+      Firewall Rulesets
+      ------------------------
+
+      IPv4 name:
+
+      Rule-set name             Description    References
+      -------------             -----------    ----------
+      DMZv4-1-OUT                              (eth0,OUT)
+      DMZv4-1-IN                               (eth0,IN)
+
+      ------------------------
+      Firewall Groups
+      ------------------------
+
+      Port Groups:
+
+      Group name                Description    References
+      ----------                -----------    ----------
+      DMZ-Ports                                DMZv4-1-OUT-10-destination
+
+      Network Groups:
+
+      Group name                Description    References
+      ----------                -----------    ----------
+      LANv4                                    LANv4-IN-10-source,
+                                                DMZv4-1-OUT-10-source,
+                                                DMZv4-1-OUT-11-source
+
+.. opcmd:: show firewall statistics
+
+   This will show you a statistic of all rule-sets since the last boot.
+   
+.. opcmd:: show firewall [name | ipv6name] <name> rule <1-9999>
+
+   This command will give an overview about a rule in a single rule-set
+
+.. opcmd:: show firewall group <name>
+
+   Overview of defined groups. You see the type, the members, and where the
+   group is used.
+
+   .. code-block:: none
+
+      vyos@vyos:~$ show firewall group DMZ-Ports
+      Name       : DMZ-Ports
+      Type       : port
+      References : none
+      Members    :
+                  80
+                  443
+                  8080
+                  8443
+      
+      vyos@vyos:~$ show firewall group LANv4
+      Name       : LANv4
+      Type       : network
+      References : LANv4-IN-10-source
+      Members    :
+                  10.10.0.0/16
+
+.. opcmd:: show firewall [name | ipv6name] <name>
+
+   This command will give an overview about a single rule-set
+
+.. opcmd:: show firewall [name | ipv6name] <name> statistics
+
+   This will show you a rule-set statistic since the last boot.
+
+.. opcmd:: show firewall [name | ipv6name] <name> rule <1-9999>
+
+   This command will give an overview about a rule in a single rule-set
+
+
+Zone-Policy Overview
+********************
+
+.. opcmd:: show zone-policy zone <name>
+
+   Use this command to get an overview about a zone
+
+   .. code-block:: none
+
+      vyos@vyos:~$ show zone-policy zone DMZ
+      -------------------
+      Name: DMZ
+
+      Interfaces: eth0 eth1
+
+      From Zone:
+      name                                    firewall
+      ----                                    --------
+      LAN                                     DMZv4-1-OUT
+
+
+Show Firewall log
+*****************
+
+.. opcmd:: show log firewall [name | ipv6name] <name>
+
+   Show the logs of a specific Rule-Set
+
+.. note::
+   At the moment it not possible to look at the whole firewall log with VyOS
+   operational commands. All logs will save to ``/var/logs/messages``.
+   For example: ``grep '10.10.0.10' /var/log/messages``
+
+
+
+Example Partial Config
+----------------------
+
+.. code-block:: none
+
+  firewall {
+     all-ping enable
+     broadcast-ping disable
+     config-trap disable
+     group {
+         network-group BAD-NETWORKS {
+             network 198.51.100.0/24
+             network 203.0.113.0/24
+         }
+         network-group GOOD-NETWORKS {
+             network 192.0.2.0/24
+         }
+         port-group BAD-PORTS {
+             port 65535
+         }
+     }
+     name FROM-INTERNET {
+         default-action accept
+         description "From the Internet"
+         rule 10 {
+             action accept
+             description "Authorized Networks"
+             protocol all
+             source {
+                 group {
+                     network-group GOOD-NETWORKS
+                 }
+             }
+         }
+         rule 11 {
+             action drop
+             description "Bad Networks"
+             protocol all
+             source {
+                 group {
+                     network-group BAD-NETWORKS
+                 }
+             }
+         }
+         rule 30 {
+             action drop
+             description "BAD PORTS"
+             destination {
+                 group {
+                     port-group BAD-PORTS
+                 }
+             }
+             log enable
+             protocol all
+         }
+     }
+  }
+  interfaces {
+     ethernet eth1 {
+         address dhcp
+         description OUTSIDE
+         duplex auto
+         firewall {
+             in {
+                 name FROM-INTERNET
+             }
+         }
+     }
+  }
diff --git a/docs/configuration/index.rst b/docs/configuration/index.rst
new file mode 100644
index 00000000..bce013cb
--- /dev/null
+++ b/docs/configuration/index.rst
@@ -0,0 +1,23 @@
+###################
+Configuration Guide
+###################
+
+The following structure respresent the cli structure.
+
+.. toctree::
+   :maxdepth: 1
+   :includehidden:
+
+   firewall/index
+   highavailability/index
+   interfaces/index
+   loadbalancing/index
+   nat/index
+   policy/index
+   protocols/index
+   service/index
+   system/index
+   trafficpolicy/index
+   vpn/index
+   vrf/index
+   zonepolicy/index
\ No newline at end of file