Refactor "code-block:: console" to "code-block:: none"

16 files changed, 122 insertions, 122 deletions

diff --git a/docs/services/conntrack.rst b/docs/services/conntrack.rst
index d40a3dbc..28f16d54 100644
--- a/docs/services/conntrack.rst
+++ b/docs/services/conntrack.rst
@@ -27,7 +27,7 @@ will be mandatorily defragmented.
 Configuration
 ^^^^^^^^^^^^^
 
-.. code-block:: console
+.. code-block:: none
 
   # Protocols only for which local conntrack entries will be synced (tcp, udp, icmp, sctp)
   set service conntrack-sync accept-protocol
@@ -69,20 +69,20 @@ The next exemple is a simple configuration of conntrack-sync.
 
 First of all, make sure conntrack is enabled by running
 
-.. code-block:: console
+.. code-block:: none
 
   show conntrack table ipv4
 
 If the table is empty and you have a warning message, it means conntrack is not
 enabled. To enable conntrack, just create a NAT or a firewall rule.
 
-.. code-block:: console
+.. code-block:: none
 
   set firewall state-policy established action accept
 
 You now should have a conntrack table
 
-.. code-block:: console
+.. code-block:: none
 
   $ show conntrack table ipv4
   TCP state codes: SS - SYN SENT, SR - SYN RECEIVED, ES - ESTABLISHED,
@@ -99,7 +99,7 @@ You now should have a conntrack table
 
 Now configure conntrack-sync service on ``router1`` **and** ``router2``
 
-.. code-block:: console
+.. code-block:: none
 
   set service conntrack-sync accept-protocol 'tcp,udp,icmp'
   set service conntrack-sync event-listen-queue-size '8'
@@ -115,7 +115,7 @@ the external-cache of the standby router
 On active router run:
 
 
-.. code-block:: console
+.. code-block:: none
 
   $ show conntrack-sync statistics
 
diff --git a/docs/services/dhcp-relay.rst b/docs/services/dhcp-relay.rst
index e2e4ff85..0b838442 100644
--- a/docs/services/dhcp-relay.rst
+++ b/docs/services/dhcp-relay.rst
@@ -28,27 +28,27 @@ Configuration
 
 Enable DHCP relay for eth1 and eth2:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcp-relay interface eth1
   set service dhcp-relay interface eth2
 
 Set the IP address of the DHCP server:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcp-relay server 10.0.1.4
 
 The router should discard DHCP packages already containing relay agent
 information to ensure that only requests from DHCP clients are forwarded:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcp-relay relay-options relay-agents-packets discard
 
 Commit the changes and show the results:
 
-.. code-block:: console
+.. code-block:: none
 
   commit
   show service dhcp-relay
@@ -61,7 +61,7 @@ Commit the changes and show the results:
 
 The DHCP relay agent can be restarted with:
 
-.. code-block:: console
+.. code-block:: none
 
   restart dhcp relay-agent
 
@@ -83,20 +83,20 @@ Configuration
 
 Set eth1 to be the listening interface for the DHCPv6 relay:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcpv6-relay listen-interface eth1
 
 Set eth2 to be the upstream interface and specify the IPv6 address of
 the DHCPv6 server:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcpv6-relay upstream-interface eth2 address 2001:db8:100::4
 
 Commit the changes and show results:
 
-.. code-block:: console
+.. code-block:: none
 
   commit
   show service dhcpv6-relay
@@ -108,13 +108,13 @@ Commit the changes and show results:
 
 Show the current status of the DHCPv6 relay agent:
 
-.. code-block:: console
+.. code-block:: none
 
   show dhcpv6 relay-agent status
 
 The DHCPv6 relay agent can be restarted with:
 
-.. code-block:: console
+.. code-block:: none
 
   restart dhcpv6 relay-agent
 
diff --git a/docs/services/dhcp.rst b/docs/services/dhcp.rst
index 81a88741..f11d9a7e 100644
--- a/docs/services/dhcp.rst
+++ b/docs/services/dhcp.rst
@@ -21,13 +21,13 @@ on `pppoe0`
 Interface Configuration
 ^^^^^^^^^^^^^^^^^^^^^^^
 
-.. code-block:: console
+.. code-block:: none
 
  set interface ethernet eth1 address 172.16.17.1/24
 
 Multiple ranges can be defined and can contain holes.
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcp-server shared-network-name dhcpexample authoritative
   set service dhcp-server shared-network-name dhcpexample subnet 172.16.17.0/24 default-router 172.16.17.1
@@ -86,7 +86,7 @@ Failover
 
 VyOS provides support for DHCP failover:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' failover local-address '192.168.0.1'
   set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' failover name 'foo'
@@ -97,13 +97,13 @@ VyOS provides support for DHCP failover:
 The primary and secondary statements determines whether the server is
 primary or secondary
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' failover status 'primary'
 
 or
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' failover status 'secondary'
 
@@ -114,7 +114,7 @@ or
 Static mappings MAC/IP
 ^^^^^^^^^^^^^^^^^^^^^^
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcp-server shared-network-name dhcpexample subnet 172.16.17.0/24 static-mapping static-mapping-01 ip-address 172.16.17.10
   set service dhcp-server shared-network-name dhcpexample subnet 172.16.17.0/24 static-mapping static-mapping-01 mac-address ff:ff:ff:ff:ff:ff
diff --git a/docs/services/dhcpv6.rst b/docs/services/dhcpv6.rst
index 799c4332..db566d5f 100644
--- a/docs/services/dhcpv6.rst
+++ b/docs/services/dhcpv6.rst
@@ -5,25 +5,25 @@ DHCPv6 server
 VyOS provides DHCPv6 server functionality which is described in this section.
 In order to use the DHCPv6 server it has to be enabled first:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcpv6-server
 
 To restart the DHCPv6 server (operational mode):
 
-.. code-block:: console
+.. code-block:: none
 
   restart dhcpv6 server
 
 To show the current status of the DHCPv6 server use:
 
-.. code-block:: console
+.. code-block:: none
 
   show dhcpv6 server status
 
 Show statuses of all assigned leases:
 
-.. code-block:: console
+.. code-block:: none
 
   show dhcpv6 server leases
 
@@ -37,19 +37,19 @@ Clients receiving advertise messages from multiple servers choose the server
 with the highest preference value. The range for this value is `0...255`. Set
 a preference value for the DHCPv6 server:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcpv6-server preference <preference value>
 
 Delete a preference:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcpv6-server preference
 
 Show current preference:
 
-.. code-block:: console
+.. code-block:: none
 
   show service dhcpv6-server preference
 
@@ -60,19 +60,19 @@ The default lease time for DHCPv6 leases is 24 hours. This can be changed by
 supplying a `default-time`, `maximum-time` and `minimum-time` (all values in
 seconds):
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcpv6-server shared-network-name <name> subnet <ipv6net> lease-time {default <default-time> | maximum <maximum-time> | minimum <minimum-time>}
 
 Reset the custom lease times:
 
-.. code-block:: console
+.. code-block:: none
 
   delete service dhcpv6-server shared-network-name <name> subnet <ipv6net> lease-time {default | maximum | minimum}
 
 Show the current configuration:
 
-.. code-block:: console
+.. code-block:: none
 
   show service dhcpv6-server shared-network-name <name> subnet <ipv6net> lease-time {default | maximum | minimum}
 
@@ -81,19 +81,19 @@ Specify NIS domain
 
 A Network Information (NIS) domain can be set to be used for DHCPv6 clients:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcpv6-server shared-network-name <name> subnet <ipv6net> nis-domain <nis-domain-name>
 
 To Delete the NIS domain:
 
-.. code-block:: console
+.. code-block:: none
 
   delete service dhcpv6-server shared-network-name <name> subnet <ipv6net> nis-domain <nis-domain-name>
 
 Show a configured NIS domain:
 
-.. code-block:: console
+.. code-block:: none
 
   show service dhcpv6-server shared-network-name <name> subnet <ipv6net> nis-domain <nis-domain-name>
 
@@ -103,13 +103,13 @@ Specify NIS+ domain
 The procedure to specify a Network Information Service Plus (NIS+) domain is
 similar to the NIS domain one:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcpv6-server shared-network-name <name> subnet <ipv6net> nisplus-domain <nisplus-domain-name>
 
 To Delete the NIS+ domain:
 
-.. code-block:: console
+.. code-block:: none
 
   delete service dhcpv6-server shared-network-name <name> subnet <ipv6net> nisplus-domain <nisplus-domain-name>
 
@@ -122,19 +122,19 @@ Specify NIS server address
 
 To specify a NIS server address for DHCPv6 clients:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcpv6-server shared-network-name <name> subnet <ipv6net> nis-server <IPv6 address>
 
 Delete a specified NIS server address:
 
-.. code-block:: console
+.. code-block:: none
 
   delete service dhcpv6-server shared-network-name <name> subnet <ipv6net> nis-server <IPv6 address>
 
 Show specified NIS server addresses:
 
-.. code-block:: console
+.. code-block:: none
 
   show service dhcpv6-server shared-network-name <name> subnet <ipv6net> nis-server
 
@@ -143,19 +143,19 @@ Specify NIS+ server address
 
 To specify a NIS+ server address for DHCPv6 clients:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcpv6-server shared-network-name <name> subnet <ipv6net> nisplus-server <IPv6 address>
 
 Delete a specified NIS+ server address:
 
-.. code-block:: console
+.. code-block:: none
 
   delete service dhcpv6-server shared-network-name <name> subnet <ipv6net> nisplus-server <IPv6 address>
 
 Show specified NIS+ server addresses:
 
-.. code-block:: console
+.. code-block:: none
 
   show service dhcpv6-server shared-network-name <name> subnet <ipv6net> nisplus-server
 
@@ -169,19 +169,19 @@ By IPv6 address
 A Session Initiation Protocol (SIP) server address can be specified
 for DHCPv6 clients:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcpv6-server shared-network-name <name> subnet <ipv6net> sip-server-address <IPv6 address>
 
 Delete a specified SIP server address:
 
-.. code-block:: console
+.. code-block:: none
 
   delete service dhcpv6-server shared-network-name <name> subnet <ipv6net> sip-server-address <IPv6 address>
 
 Show specified SIP server addresses:
 
-.. code-block:: console
+.. code-block:: none
 
   show service dhcpv6-server shared-network-name <name> subnet <ipv6net> sip-server-address
 
@@ -190,19 +190,19 @@ By FQDN
 
 A name for SIP server can be specified:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcpv6-server shared-network-name <name> subnet <ipv6net> sip-server-name <sip-server-name>
 
 Delete a specified SIP server name:
 
-.. code-block:: console
+.. code-block:: none
 
   delete service dhcpv6-server shared-network-name <name> subnet <ipv6net> sip-server-name <sip-server-name>
 
 Show specified SIP server names:
 
-.. code-block:: console
+.. code-block:: none
 
   show service dhcpv6-server shared-network-name <name> subnet <ipv6net> sip-server-name
 
@@ -211,19 +211,19 @@ Simple Network Time Protocol (SNTP) server address for DHCPv6 clients
 
 A SNTP server address can be specified for DHCPv6 clients:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcpv6-server shared-network-name <name> subnet <ipv6net> sntp-server-address <IPv6 address>
 
 Delete a specified SNTP server address:
 
-.. code-block:: console
+.. code-block:: none
 
   delete service dhcpv6-server shared-network-name <name> subnet <ipv6net> sntp-server-address <IPv6 address>
 
 Show specified SNTP server addresses:
 
-.. code-block:: console
+.. code-block:: none
 
   show service dhcpv6-server shared-network-name <name> subnet <ipv6net> sntp-server-address
 
@@ -241,14 +241,14 @@ connected to `eth1`, a DNS server at `2001:db8:111::111` is used for name
 services. The range of the address pool shall be `::100` through `::199`. The
 lease time will be left at the default value which is 24 hours.
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcpv6-server shared-network-name NET1 subnet 2001:db8:100::/64 address-range start 2001:db8:100::100 stop 2001:db8:100::199
   set service dhcpv6-server shared-network-name NET1 subnet 2001:db8:100::/64 name-server 2001:db8:111::111
 
 Commit the changes and show the configuration:
 
-.. code-block:: console
+.. code-block:: none
 
   commit
   show service dhcpv6-server
@@ -279,14 +279,14 @@ MAC address `00:15:c5:b7:5e:23`, this host-specific mapping shall be named
 .. note:: The MAC address identifier is defined by the last 4 byte of the
    MAC address.
 
-.. code-block:: console
+.. code-block:: none
 
   set service dhcpv6-server shared-network-name NET1 subnet 2001:db8:100::/64 static-mapping client1 ipv6-address 2001:db8:100::101
   set service dhcpv6-server shared-network-name NET1 subnet 2001:db8:100::/64 static-mapping client1 identifier c5b75e23
 
 Commit the changes and show the configuration:
 
-.. code-block:: console
+.. code-block:: none
 
   show service dhcp-server shared-network-name NET1
      shared-network-name NET1 {
diff --git a/docs/services/dns-forwarding.rst b/docs/services/dns-forwarding.rst
index 2ab04707..84e4fc93 100644
--- a/docs/services/dns-forwarding.rst
+++ b/docs/services/dns-forwarding.rst
@@ -5,33 +5,33 @@ Use DNS forwarding if you want your router to function as a DNS server for the
 local network. There are several options, the easiest being 'forward all
 traffic to the system DNS server(s)' (defined with set system name-server):
 
-.. code-block:: console
+.. code-block:: none
 
   set service dns forwarding system
 
 Manually setting DNS servers for forwarding:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dns forwarding name-server 8.8.8.8
   set service dns forwarding name-server 8.8.4.4
 
 Manually setting DNS servers with IPv6 connectivity:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dns forwarding name-server 2001:4860:4860::8888
   set service dns forwarding name-server 2001:4860:4860::8844
 
 Setting a forwarding DNS server for a specific domain:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dns forwarding domain example.com server 192.0.2.1
   
 Set which networks or clients are allowed to query the DNS Server. Allow from all:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dns forwarding allow-from 0.0.0.0/0
 
@@ -44,7 +44,7 @@ Router with two interfaces eth0 (WAN link) and eth1 (LAN). Split DNS for example
 * Other DNS requests are forwarded to Google's DNS servers.
 * The IP address for the LAN interface is 192.168.0.1.
 
-.. code-block:: console
+.. code-block:: none
 
   set service dns forwarding domain example.com server 192.0.2.1
   set service dns forwarding name-server 8.8.8.8
@@ -60,7 +60,7 @@ servers.
 
 The IP addresses for the LAN interface are 192.168.0.1 and 2001:db8::1
 
-.. code-block:: console
+.. code-block:: none
 
   set service dns forwarding domain example.com server 192.0.2.1
   set service dns forwarding name-server 8.8.8.8
diff --git a/docs/services/dynamic-dns.rst b/docs/services/dynamic-dns.rst
index a0d75979..6a3c6e28 100644
--- a/docs/services/dynamic-dns.rst
+++ b/docs/services/dynamic-dns.rst
@@ -16,44 +16,44 @@ VyOS CLI and RFC2136
 
 First, create an RFC2136_ config node :
 
-.. code-block:: console
+.. code-block:: none
 
   edit service dns dynamic interface eth0 rfc2136 <confignodename>
 
 Present your RNDC key to ddclient :
 
-.. code-block:: console
+.. code-block:: none
 
   set key /config/dyndns/mydnsserver.rndc.key
 
 Set the DNS server IP/FQDN :
 
-.. code-block:: console
+.. code-block:: none
 
   set server dns.mydomain.com
 
 Set the NS zone to be updated :
 
-.. code-block:: console
+.. code-block:: none
 
   set zone mydomain.com
 
 Set the records to be updated :
 
-.. code-block:: console
+.. code-block:: none
 
   set record dyn
   set record dyn2
 
 You can optionally set a TTL (note : default value is 600 seconds) :
 
-.. code-block:: console
+.. code-block:: none
 
   set ttl 600
 
 This will generate the following ddclient config blocks:
 
-.. code-block:: console
+.. code-block:: none
 
   server=dns.mydomain.com
   protocol=nsupdate
@@ -70,7 +70,7 @@ This will generate the following ddclient config blocks:
 
 You can also keep a different dns zone updated. Just create a new config node:
 
-.. code-block:: console
+.. code-block:: none
 
   edit service dns dynamic interface eth0 rfc2136 <confignode2>
 
@@ -83,7 +83,7 @@ by ddclient.
 To use such a service, you must define a login, a password, one or multiple
 hostnames, a protocol and a server.
 
-.. code-block:: console
+.. code-block:: none
 
   edit service dns dynamic interface eth0 service HeNet
   set login my-login # set password my-password
@@ -107,7 +107,7 @@ the services VyOS knows about:
 
 To use DynDNS for example:
 
-.. code-block:: console
+.. code-block:: none
 
   edit service dns dynamic interface eth0 service dyndns
   set login my-login
@@ -116,7 +116,7 @@ To use DynDNS for example:
 
 It's possible to use multiple services :
 
-.. code-block:: console
+.. code-block:: none
 
   edit service dns dynamic interface eth0 service dyndns
   set login my-login
@@ -139,7 +139,7 @@ record will be updated to point to your internal IP.
 ddclient_ has another way to determine the WAN IP address. This is controlled
 by these two options:
 
-.. code-block:: console
+.. code-block:: none
 
   set service dns dynamic interface eth0 use-web url
   set service dns dynamic interface eth0 use-web skip
diff --git a/docs/services/ipoe-server.rst b/docs/services/ipoe-server.rst
index 1e5e72dc..eed4cced 100644
--- a/docs/services/ipoe-server.rst
+++ b/docs/services/ipoe-server.rst
@@ -17,7 +17,7 @@ The clients mac address and the incoming interface is being used as control para
 The example configuration below will assign an IP to the client on the incoming interface eth2 with the client mac address 08:00:27:2f:d8:06.
 Other DHCP discovery requests will be ignored, unless the client mac has been enabled in the configuration.
 
-.. code-block:: console
+.. code-block:: none
 
   set service ipoe-server authentication interface eth2 mac-address 08:00:27:2f:d8:06
   set service ipoe-server authentication mode 'local'
@@ -29,7 +29,7 @@ Other DHCP discovery requests will be ignored, unless the client mac has been en
 The first address of the parameter ``client-subnet``, will be used as the default gateway. 
 Connected sessions can be checked via the ``show ipoe-server sessions`` command.
 
-.. code-block:: console
+.. code-block:: none
 
   vyos@vyos:~$ show ipoe-server sessions
 
@@ -46,7 +46,7 @@ for devices routed via the clients cpe.
 
 IPv6 DNS addresses are optional.
 
-.. code-block:: console
+.. code-block:: none
 
   set service ipoe-server authentication interface eth3 mac-address 08:00:27:2F:D8:06
   set service ipoe-server authentication mode 'local'
@@ -57,7 +57,7 @@ IPv6 DNS addresses are optional.
   set service ipoe-server dnsv6-server server-3 '2001:db8:bbb::'
   set service ipoe-server interface eth3 client-subnet '192.168.1.0/24'
 
-.. code-block:: console
+.. code-block:: none
 
   vyos@ipoe-server# run sh ipoe-server sessions 
   ifname | called-sid |    calling-sid    |     ip      |               ip6               | ip6-dp          | rate-limit | state  |  uptime  |        sid       
@@ -74,7 +74,7 @@ Automatic VLAN creation
 
 To create VLANs per user during runtime, the following settings are required on a per interface basis. VLAN ID and VLAN range can be present in the configuration at the same time.
 
-.. code-block:: console
+.. code-block:: none
 
   set service ipoe-server interface eth2 network vlan
   set service ipoe-server interface eth2 vlan-id 100
@@ -88,7 +88,7 @@ RADIUS Setup
 
 To use a RADIUS server for authentication and bandwidth-shaping, the following example configuration can be used.
 
-.. code-block:: console
+.. code-block:: none
 
   set service ipoe-server authentication mode 'radius'
   set service ipoe-server authentication radius-server 10.100.100.1 secret 'password'
@@ -105,7 +105,7 @@ Bandwidth Shaping for local users
 
 The rate-limit is set in kbit/sec.
 
-.. code-block:: console
+.. code-block:: none
 
   set service ipoe-server authentication interface eth2 mac-address 08:00:27:2f:d8:06 rate-limit download '500'
   set service ipoe-server authentication interface eth2 mac-address 08:00:27:2f:d8:06 rate-limit upload '500'
@@ -115,7 +115,7 @@ The rate-limit is set in kbit/sec.
   set service ipoe-server interface eth2 client-subnet '192.168.0.0/24'
 
 
-.. code-block:: console
+.. code-block:: none
 
   vyos@vyos# run show ipoe-server sessions 
 
diff --git a/docs/services/lldp.rst b/docs/services/lldp.rst
index d58e105e..dccd68fa 100644
--- a/docs/services/lldp.rst
+++ b/docs/services/lldp.rst
@@ -74,7 +74,7 @@ Display neighbors
 
 Exemple:
 
-.. code-block:: console
+.. code-block:: none
 
   vyos@vyos:~# show lldp neighbors
   Capability Codes: R - Router, B - Bridge, W - Wlan r - Repeater, S - Station
diff --git a/docs/services/mdns-repeater.rst b/docs/services/mdns-repeater.rst
index abd3f7ef..22e824ba 100644
--- a/docs/services/mdns-repeater.rst
+++ b/docs/services/mdns-repeater.rst
@@ -12,14 +12,14 @@ multiple VLANs.
 To enable mDNS repeater you need to configure at least two interfaces. To re-
 broadcast all mDNS packets from `eth0` to `eth1` and vice versa run:
 
-.. code-block:: console
+.. code-block:: none
 
   set service mdns repeater interface eth0
   set service mdns repeater interface eth1
 
 mDNS repeater can be temporarily disabled without deleting the service using
 
-.. code-block:: console
+.. code-block:: none
 
   set service mdns repeater disable
 
diff --git a/docs/services/pppoe-server.rst b/docs/services/pppoe-server.rst
index 3f42ceab..8e37a068 100644
--- a/docs/services/pppoe-server.rst
+++ b/docs/services/pppoe-server.rst
@@ -15,7 +15,7 @@ The example below uses ACN as access-concentrator name, assigns an address
 from the pool 10.1.1.100-111, terminates at the local endpoint 10.1.1.1 and
 serves requests only on eth1.
 
-.. code-block:: console
+.. code-block:: none
 
   set service pppoe-server access-concentrator 'ACN'
   set service pppoe-server authentication local-users username foo password 'bar'
@@ -30,7 +30,7 @@ serves requests only on eth1.
 
 Connections can be locally checked via the command
 
-.. code-block:: console
+.. code-block:: none
 
   show pppoe-server sessions
   ifname | username |     ip     |    calling-sid    | rate-limit  | state  |  uptime  | rx-bytes | tx-bytes 
@@ -48,7 +48,7 @@ If the CIDR notation is used, multiple subnets can be setup which are used seque
 
 **Client IP address via IP range definition**
 
-.. code-block:: console
+.. code-block:: none
 
   set service pppoe-server client-ip-pool start '10.1.1.100'
   set service pppoe-server client-ip-pool stop '10.1.1.111'
@@ -56,7 +56,7 @@ If the CIDR notation is used, multiple subnets can be setup which are used seque
 
 **Client IP subnets via CIDR notation**
 
-.. code-block:: console
+.. code-block:: none
 
   set service pppoe-server client-ip-pool subnet '10.1.1.0/24'
   set service pppoe-server client-ip-pool subnet '10.1.2.0/24'
@@ -70,7 +70,7 @@ To use a radius server, you need to switch to authentication mode radius and
 of course need to specify an IP for the server. You can have multiple RADIUS
 server configured, if you wish to achieve redundancy.
 
-.. code-block:: console
+.. code-block:: none
 
   set service pppoe-server access-concentrator 'ACN'
   set service pppoe-server authentication mode 'radius'
@@ -84,7 +84,7 @@ RADIUS provides the IP addresses in the example above via Framed-IP-Address.
 
 For remotely disconnect sessions and change some authentication parameters you can configure dae-server
 
-.. code-block:: console
+.. code-block:: none
 
   set service pppoe-server authentication radius-settings dae-server ip-address '10.1.1.2'
   set service pppoe-server authentication radius-settings dae-server port '3799'
@@ -92,20 +92,20 @@ For remotely disconnect sessions and change some authentication parameters you c
 
 Example, from radius-server send command for disconnect client with username test
 
-.. code-block:: console
+.. code-block:: none
 
   root@radius-server:~# echo "User-Name=test" | radclient -x 10.1.1.2:3799 disconnect secret123
   
 You can also use another attributes for identify client for disconnect, like Framed-IP-Address, Acct-Session-Id, etc.
 Result commands appears in log
 
-.. code-block:: console
+.. code-block:: none
 
   show log | match Disconnect*
 
 Example for changing rate-limit via RADIUS CoA
 
-.. code-block:: console
+.. code-block:: none
 
   echo "User-Name=test,Filter-Id=5000/4000" | radclient 10.1.1.2:3799 coa secret123
 
@@ -119,7 +119,7 @@ Automatic VLAN creation
 VLAN's can be created by accel-ppp on the fly if via the use of the kernel module vlan_mon, which is monitoring incoming vlans and creates the necessary VLAN if required and allowed.
 VyOS supports the use of either VLAN ID's or entire ranges, both values can be defined at the same time for an interface.
 
-.. code-block:: console
+.. code-block:: none
 
   set service pppoe-server interface eth3 vlan-id 100
   set service pppoe-server interface eth3 vlan-id 200
@@ -141,7 +141,7 @@ Bandwidth Shaping for local users
 
 The rate-limit is set in kbit/sec.
 
-.. code-block:: console
+.. code-block:: none
 
   set service pppoe-server access-concentrator 'ACN'
   set service pppoe-server authentication local-users username foo password 'bar'
@@ -158,7 +158,7 @@ The rate-limit is set in kbit/sec.
 
 Once the user is connected, the user session is using the set limits and can be displayed via 'show pppoe-server sessions'.
 
-.. code-block:: console
+.. code-block:: none
 
   show pppoe-server sessions
   ifname | username |     ip     |    calling-sid    | rate-limit  | state  |  uptime  | rx-bytes | tx-bytes
@@ -175,7 +175,7 @@ Filter-Id=2000/3000 (means 2000Kbit down-stream rate and 3000Kbit up-stream rate
 
 The command below enables it, assuming the RADIUS connection has been setup and is working.
 
-.. code-block:: console
+.. code-block:: none
 
   set service pppoe-server authentication radius-settings rate-limit enable
 
@@ -191,7 +191,7 @@ Dual-stack provisioning with IPv6 PD via pppoe
 
 The example below covers a dual-stack configuration via pppoe-server.
 
-.. code-block:: console
+.. code-block:: none
 
   set service pppoe-server authentication local-users username test password 'test'
   set service pppoe-server authentication mode 'local'
@@ -207,7 +207,7 @@ The example below covers a dual-stack configuration via pppoe-server.
 
 The client, once successfully authenticated, will receive an IPv4 and an IPv6 /64 address, to terminate the pppoe endpoint on the client side and a /56 subnet for the clients internal use.
 
-.. code-block:: console
+.. code-block:: none
 
   vyos@pppoe-server:~$ sh pppoe-server sessions 
    ifname | username |     ip      |            ip6           |       ip6-dp        |    calling-sid    | rate-limit | state  |  uptime  | rx-bytes | tx-bytes 
diff --git a/docs/services/snmp.rst b/docs/services/snmp.rst
index 8fd6a21e..6418a516 100644
--- a/docs/services/snmp.rst
+++ b/docs/services/snmp.rst
@@ -90,7 +90,7 @@ plain text.
 Example
 *******
 
-.. code-block:: console
+.. code-block:: none
 
   # Define a community
   set service snmp community routers authorization ro
@@ -139,7 +139,7 @@ The securityapproach in v3 targets:
 Example
 *******
 
-.. code-block:: console
+.. code-block:: none
 
   set service snmp v3 engineid '0x0aa0d6c6f450'
   set service snmp v3 group defaultgroup mode 'ro'
@@ -160,7 +160,7 @@ After commit the resulting configuration will look like:
 .. note:: SNMPv3 keys won't we stored in plaintext. On ``commit`` the keys
    will be encrypted and the encrypted key is based on the engineid!
 
-.. code-block:: console
+.. code-block:: none
 
   vyos@vyos# show service snmp
    v3 {
@@ -200,7 +200,7 @@ vyos@your_router:/config/user-data``. Once the script is uploaded, it needs to
 be configured via the command below.
 
 
-.. code-block:: console
+.. code-block:: none
 
   set service snmp script-extensions extension-name my-extension script your_script.sh
   commit
@@ -209,7 +209,7 @@ be configured via the command below.
 The OID ``.1.3.6.1.4.1.8072.1.3.2.3.1.1.4.116.101.115.116``, once called, will
 contain the output of the extension.
 
-.. code-block:: console
+.. code-block:: none
 
   root@vyos:/home/vyos# snmpwalk -v2c  -c public 127.0.0.1 nsExtendOutput1
   NET-SNMP-EXTEND-MIB::nsExtendOutput1Line."my-extension" = STRING: hello
@@ -226,7 +226,7 @@ Templates Management. A template for VyOS can be easily imported.
 Create a file named ``VyOS-1.3.6.1.4.1.44641.ConfigMgmt-Commands`` using the
 following content:
 
-.. code-block:: console
+.. code-block:: none
 
   <Configuration-Management Device="VyOS" SystemOID="1.3.6.1.4.1.44641">
       <Commands>
diff --git a/docs/services/ssh.rst b/docs/services/ssh.rst
index c770140b..3af71899 100644
--- a/docs/services/ssh.rst
+++ b/docs/services/ssh.rst
@@ -30,7 +30,7 @@ Configuration
 Enabling SSH only requires you to add ``service ssh port NN``, where 'NN' is
 the port you want SSH to listen on. By default, SSH runs on port 22.
 
-.. code-block:: console
+.. code-block:: none
 
   set service ssh port 22
 
@@ -130,7 +130,7 @@ line. The third part is simply an identifier, and is for your own reference.
 Under the user (in this example, ``vyos``), add the public key and the type.
 The `identifier` is simply a string that is relevant to you.
 
-.. code-block:: console
+.. code-block:: none
 
   set system login user vyos authentication public-keys 'identifier' key "AAAAB3Nz...."
   set system login user vyos authentication public-keys 'identifier' type ssh-rsa"
@@ -139,7 +139,7 @@ You can assign multiple keys to the same user by changing the identifier. In
 the following example, both Unicron and xrobau will be able to SSH into VyOS
 as the ``vyos`` user using their own keys.
 
-.. code-block:: console
+.. code-block:: none
 
   set system login user vyos authentication public-keys 'Unicron' key "AAAAB3Nz...."
   set system login user vyos authentication public-keys 'Unicron' type ssh-rsa
diff --git a/docs/services/sstp-server.rst b/docs/services/sstp-server.rst
index 6a394cc5..428a2e46 100644
--- a/docs/services/sstp-server.rst
+++ b/docs/services/sstp-server.rst
@@ -22,7 +22,7 @@ Self Signed CA and server certificates
 
 To generate the CA, the server private key and certificates the following commands can be used.
 
-.. code-block:: console
+.. code-block:: none
 
   vyos@vyos:~$ conf
   [edit]
@@ -60,7 +60,7 @@ The example below will answer configuration request for the user user ``foo``.
 
 Use <tab> to setup the ``set sstp-settings ssl-certs ...``, it automatically looks for all files and directories in ``/config/user-data/sstp``. 
 
-.. code-block:: console
+.. code-block:: none
 
   edit service sstp-server
   set authentication local-users username foo password 'bar'
diff --git a/docs/services/tftp.rst b/docs/services/tftp.rst
index 185e594f..9ce46b02 100644
--- a/docs/services/tftp.rst
+++ b/docs/services/tftp.rst
@@ -10,7 +10,7 @@ simple to implement.
 Example
 ^^^^^^^
 
-.. code-block:: console
+.. code-block:: none
 
   # If you want to enable uploads, else TFTP server will act as read-only (optional)
   set service tftp-server allow-upload
@@ -30,7 +30,7 @@ Example
 
 The resulting configuration will look like:
 
-.. code-block:: console
+.. code-block:: none
 
   vyos@vyos# show service
    tftp-server {
diff --git a/docs/services/udp-broadcast-relay.rst b/docs/services/udp-broadcast-relay.rst
index 995213fa..40f738e6 100644
--- a/docs/services/udp-broadcast-relay.rst
+++ b/docs/services/udp-broadcast-relay.rst
@@ -14,7 +14,7 @@ support 99 IDs!
 Example #1: To forward all broadcast packets received on `UDP port 1900` on
 `eth3`, `eth4` or `eth5` to all other interfaces in this configuration.
 
-.. code-block:: console
+.. code-block:: none
 
   set service broadcast-relay id 1 description 'SONOS'
   set service broadcast-relay id 1 interface 'eth3'
@@ -25,7 +25,7 @@ Example #1: To forward all broadcast packets received on `UDP port 1900` on
 Example #2: To Forward all broadcasts packets received on `UDP port 6969` on
 `eth3` or `eth4` to the other interface in this configuration.
 
-.. code-block:: console
+.. code-block:: none
 
   set service broadcast-relay id 2 description 'SONOS MGMT'
   set service broadcast-relay id 2 interface 'eth3'
@@ -38,14 +38,14 @@ Disable Instance(s)
 Each broadcast relay instance can be individually disabled without deleting the
 configured node by using the following command:
 
-.. code-block:: console
+.. code-block:: none
 
   set service broadcast-relay id <n> disable
 
 In addition you can also disable the whole service without removing the
 configuration by:
 
-.. code-block:: console
+.. code-block:: none
 
   set service broadcast-relay disable
 
diff --git a/docs/services/webproxy.rst b/docs/services/webproxy.rst
index 8aca0b85..61546cda 100644
--- a/docs/services/webproxy.rst
+++ b/docs/services/webproxy.rst
@@ -19,7 +19,7 @@ URL Filtering is provided by Squidguard_.
 Configuration
 ^^^^^^^^^^^^^^
 
-.. code-block:: console
+.. code-block:: none
 
   # Enable proxy service
   set service webproxy listen-address 192.168.0.1
@@ -46,7 +46,7 @@ Filtering by category
 If you wan't to use existing blacklists you have to create/download a database
 first. Otherwise you will not be able to commit the config changes.
 
-.. code-block:: console
+.. code-block:: none
 
   vyos@vyos# commit
   [ service webproxy ]
@@ -83,7 +83,7 @@ The embedded Squid proxy can use LDAP to authenticate users against a company
 wide directory. The following configuration is an example of how to use Active
 Directory as authentication backend. Queries are done via LDAP.
 
-.. code-block:: console
+.. code-block:: none
 
   vyos@vyos# show service webproxy
    authentication {
@@ -117,7 +117,7 @@ Adjusting cache size
 
 The size of the proxy cache can be adjusted by the user.
 
-.. code-block:: console
+.. code-block:: none
 
   set service webproxy cache-size
    Possible completions: