path: root/docs/configuration/interfaces/wireguard.rst

.. _wireguard:

.. include:: /_include/need_improvement.txt

#########
WireGuard
#########

WireGuard is an extremely simple yet fast and modern VPN that utilizes
state-of-the-art cryptography. See https://www.wireguard.com for more
information.

*************
Configuration
*************

WireGuard requires the generation of a keypair, which includes a private
key to decrypt incoming traffic, and a public key for peer(s) to encrypt
traffic.

Generate Keypair
================

.. opcmd:: generate wireguard default-keypair

   It generates the keypair, which includes the public and private parts,
   and stores it within VyOS. It will be used per default on any configured
   WireGuard interface, even if multiple interfaces are being configured.

.. opcmd:: show wireguard keypairs pubkey default

   It shows the public key to be shared with your peer(s). Your peer will
   encrypt all traffic to your system using this public key.

   .. code-block:: none

     vyos@vyos:~$ show wireguard keypairs pubkey default
     hW17UxY7zeydJNPIyo3UtGnBHkzTK/NeBOrDSIU9Tx0=


Generate Named Keypair
======================

Named keypairs can be used on a interface basis when configured. If
multiple WireGuard interfaces are being configured, each can have their
own keypairs.

.. opcmd:: generate wireguard named-keypairs <name>

  The commands below generates 2 keypairs unrelated to each other.

  .. code-block:: none

    vyos@vyos:~$ generate wireguard named-keypairs KP01
    vyos@vyos:~$ generate wireguard named-keypairs KP02


Interface configuration
=======================

The next step is to configure your local side as well as the policy
based trusted destination addresses. If you only initiate a connection,
the listen port and address/port is optional; however, if you act as a
server and endpoints initiate the connections to your system, you need to
define a port your clients can connect to, otherwise the port is randomly
chosen and may make connection difficult with firewall rules, since the port
may be different each time the system is rebooted.

You will also need the public key of your peer as well as the network(s)
you want to tunnel (allowed-ips) to configure a WireGuard tunnel. The
public key below is always the public key from your peer, not your local
one.

**local side**

.. code-block:: none

  set interfaces wireguard wg01 address '10.1.0.1/24'
  set interfaces wireguard wg01 description 'VPN-to-wg02'
  set interfaces wireguard wg01 peer to-wg02 allowed-ips '10.2.0.0/24'
  set interfaces wireguard wg01 peer to-wg02 address '192.168.0.142'
  set interfaces wireguard wg01 peer to-wg02 port '12345'
  set interfaces wireguard wg01 peer to-wg02 pubkey 'XMrlPykaxhdAAiSjhtPlvi30NVkvLQliQuKP7AI7CyI='
  set interfaces wireguard wg01 port '12345'
  set protocols static route 10.2.0.0/24 interface wg01

The last step is to define an interface route for 10.2.0.0/24 to get
through the WireGuard interface `wg01`. Multiple IPs or networks can be
defined and routed. The last check is allowed-ips which either prevents
or allows the traffic.

.. note:: You can not assign the same allowed-ips statement to multiple
   WireGuard peers. This a a design decission. For more information please
   check the `WireGuard mailing list`_.

.. cfgcmd:: set interfaces wireguard <interface> private-key <name>

  To use a named key on an interface, the option private-key needs to be
  set.

  .. code-block:: none

    set interfaces wireguard wg01 private-key KP01

  The command :opcmd:`show wireguard keypairs pubkey KP01` will then show the
  public key, which needs to be shared with the peer.


**remote side**

.. code-block:: none

  set interfaces wireguard wg01 address '10.2.0.1/24'
  set interfaces wireguard wg01 description 'VPN-to-wg01'
  set interfaces wireguard wg01 peer to-wg02 allowed-ips '10.1.0.0/24'
  set interfaces wireguard wg01 peer to-wg02 address '192.168.0.124'
  set interfaces wireguard wg01 peer to-wg02 port '12345'
  set interfaces wireguard wg01 peer to-wg02 pubkey 'u41jO3OF73Gq1WARMMFG7tOfk7+r8o8AzPxJ1FZRhzk='
  set interfaces wireguard wg01 port '12345'
  set protocols static route 10.1.0.0/24 interface wg01

Assure that your firewall rules allow the traffic, in which case you
have a working VPN using WireGuard.

.. code-block:: none

  wg01# ping 10.2.0.1
  PING 10.2.0.1 (10.2.0.1) 56(84) bytes of data.
  64 bytes from 10.2.0.1: icmp_seq=1 ttl=64 time=1.16 ms
  64 bytes from 10.2.0.1: icmp_seq=2 ttl=64 time=1.77 ms

  wg02# ping 10.1.0.1
  PING 10.1.0.1 (10.1.0.1) 56(84) bytes of data.
  64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=4.40 ms
  64 bytes from 10.1.0.1: icmp_seq=2 ttl=64 time=1.02 ms

An additional layer of symmetric-key crypto can be used on top of the
asymmetric crypto. This is optional.

.. code-block:: none

  wg01# run generate wireguard preshared-key
  rvVDOoc2IYEnV+k5p7TNAmHBMEGTHbPU8Qqg8c/sUqc=

Copy the key, as it is not stored on the local filesystem. Because it
is a symmetric key, only you and your peer should have knowledge of
its content. Make sure you distribute the key in a safe manner,

.. code-block:: none

  wg01# set interfaces wireguard wg01 peer to-wg02 preshared-key 'rvVDOoc2IYEnV+k5p7TNAmHBMEGTHbPU8Qqg8c/sUqc='
  wg02# set interfaces wireguard wg01 peer to-wg01 preshared-key 'rvVDOoc2IYEnV+k5p7TNAmHBMEGTHbPU8Qqg8c/sUqc='

Road Warrior Example
--------------------

With WireGuard, a Road Warrior VPN config is similar to a site-to-site
VPN. It just lacks the ``address`` and ``port`` statements.

In the following example, the IPs for the remote clients are defined in
the peers. This allows the peers to interact with one another.

.. code-block:: none

    wireguard wg0 {
        address 10.172.24.1/24
        address 2001:DB8:470:22::1/64
        description RoadWarrior
        peer MacBook {
            allowed-ips 10.172.24.30/32
            allowed-ips 2001:DB8:470:22::30/128
            persistent-keepalive 15
            pubkey F5MbW7ye7DsoxdOaixjdrudshjjxN5UdNV+pGFHqehc=
        }
        peer iPhone {
            allowed-ips 10.172.24.20/32
            allowed-ips 2001:DB8:470:22::20/128
            persistent-keepalive 15
            pubkey BknHcLFo8nOo8Dwq2CjaC/TedchKQ0ebxC7GYn7Al00=
        }
        port 2224
    }

The following is the config for the iPhone peer above. It's important to
note that the ``AllowedIPs`` setting directs all IPv4 and IPv6 traffic
through the connection.

.. code-block:: none

    [Interface]
    PrivateKey = ARAKLSDJsadlkfjasdfiowqeruriowqeuasdf=
    Address = 10.172.24.20/24, 2001:DB8:470:22::20/64
    DNS = 10.0.0.53, 10.0.0.54

    [Peer]
    PublicKey = RIbtUTCfgzNjnLNPQ/ulkGnnB2vMWHm7l2H/xUfbyjc=
    AllowedIPs = 0.0.0.0/0, ::/0
    Endpoint = 192.0.2.1:2224
    PersistentKeepalive = 25


This MacBook peer is doing split-tunneling, where only the subnets local
to the server go over the connection.

.. code-block:: none

    [Interface]
    PrivateKey = 8Iasdfweirousd1EVGUk5XsT+wYFZ9mhPnQhmjzaJE6Go=
    Address = 10.172.24.30/24, 2001:DB8:470:22::30/64

    [Peer]
    PublicKey = RIbtUTCfgzNjnLNPQ/ulkGnnB2vMWHm7l2H/xUfbyjc=
    AllowedIPs = 10.172.24.30/24, 2001:DB8:470:22::/64
    Endpoint = 192.0.2.1:2224
    PersistentKeepalive = 25


********************
Operational Commands
********************

Status
======

.. opcmd:: show interfaces wireguard

  Get a list of all wireguard interfaces

  .. code-block:: none

    Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
    Interface        IP Address                        S/L  Description
    ---------        ----------                        ---  -----------
    wg0              10.0.0.1/24                       u/u


.. opcmd:: show interfaces wireguard <interface>

  Show general information about specific WireGuard interface

  .. code-block:: none

    vyos@vyos:~$ show interfaces wireguard wg01
    interface: wg0
      address: 10.0.0.1/24
      public key: h1HkYlSuHdJN6Qv4Hz4bBzjGg5WUty+U1L7DJsZy1iE=
      private key: (hidden)
      listening port: 41751

        RX:  bytes  packets  errors  dropped  overrun       mcast
                 0        0       0        0        0           0
        TX:  bytes  packets  errors  dropped  carrier  collisions
                 0        0       0        0        0           0

Encryption Keys
===============

.. opcmd:: show wireguard keypair pubkey <name>

  Show public key portion for specified key. This can be either the ``default``
  key, or any other named key-pair.

  The ``default`` keypair

  .. code-block:: none

    vyos@vyos:~$ show wireguard keypair pubkey default
    FAXCPb6EbTlSH5200J5zTopt9AYXneBthAySPBLbZwM=

  Name keypair ``KP01``

  .. code-block:: none

    vyos@vyos:~$ show wireguard keypair pubkey KP01
    HUtsu198toEnm1poGoRTyqkUKfKUdyh54f45dtcahDM=

.. opcmd:: delete wireguard keypair pubkey <name>

  Delete a keypair, this can be either the ``default`` key, or any other
  named key-pair.

  .. code-block:: none

    vyos@vyos:~$ delete wireguard keypair default


Mobile "RoadWarrior" clients
============================

Some users tend to connect their mobile devices using WireGuard to their VyOS
router. To ease deployment one can generate a "per mobile" configuration from
the VyOS CLI.

.. warning:: From a security perspective it is not recommended to let a third
  party create the private key for a secured connection. You should create the
  private portion on your own and only hand out the public key. Please keep this
  in mind when using this convenience feature.

.. opcmd:: generate wireguard client-config <name> interface <interface> server <ip|fqdn> address <client-ip>

  Using this command you will create a new client configuration which can
  connect to ``interface`` on this router. The public key from the specified
  interface is automatically extracted and embedded into the configuration.

  The command also generates a configuration snipped which can be copy/pasted
  into the VyOS CLI if needed. The supplied ``<name>`` on the CLI will become
  the peer name in the snippet.

  In addition you will specifiy the IP address or FQDN for the client where it
  will connect to. The address parameter can be used up to two times and is used
  to assign the client its specific IPv4 (/32) or IPv6 (/128) address.

  .. figure:: /_static/images/wireguard_qrcode.jpg
     :alt: WireGuard Client QR code

.. stop_vyoslinter

.. _`WireGuard mailing list`: https://lists.zx2c4.com/pipermail/wireguard/2018-December/003704.html

.. start_vyoslinter