1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
|
.. _wireguard:
#########
WireGuard
#########
WireGuard is an extremely simple yet fast and modern VPN that utilizes
state-of-the-art cryptography. See https://www.wireguard.com for more
information.
Configuration
=============
WireGuard requires the generation of a keypair, a private key which will
decrypt incoming traffic and a public key, which the peer(s) will use to
encrypt traffic.
Generate keypair
----------------
.. opcmd:: generate wireguard default-keypair
It generates the keypair, that is its public and private part and stores
it within VyOS. It will be used per default on any configured WireGuard
interface, even if multiple interfaces are being configured.
.. opcmd:: show wireguard keypairs pubkey default
It shows the public key which needs to be shared with your peer(s). Your
peer will encrypt all traffic to your system using this public key.
.. code-block:: none
vyos@vyos:~$ show wireguard keypairs pubkey default
hW17UxY7zeydJNPIyo3UtGnBHkzTK/NeBOrDSIU9Tx0=
Generate named keypair
----------------------
Named keypairs can be used on a interface basis, if configured. If
multiple WireGuard interfaces are being configured, each can have their
own keypairs.
The commands below will generate 2 keypairs, which are not related to
each other.
.. code-block:: none
vyos@vyos:~$ generate wireguard named-keypairs KP01
vyos@vyos:~$ generate wireguard named-keypairs KP02
Interface configuration
-----------------------
The next step is to configure your local side as well as the policy
based trusted destination addresses. If you only initiate a connection,
the listen port and address/port is optional, if you however act as a server
and endpoints initiate the connections to your system, you need to
define a port your clients can connect to, otherwise it's randomly
chosen and may make it difficult with firewall rules, since the port may
be a different one when you reboot your system.
You will also need the public key of your peer as well as the network(s)
you want to tunnel (allowed-ips) to configure a WireGuard tunnel. The
public key below is always the public key from your peer, not your local
one.
**local side**
.. code-block:: none
set interfaces wireguard wg01 address '10.1.0.1/24'
set interfaces wireguard wg01 description 'VPN-to-wg02'
set interfaces wireguard wg01 peer to-wg02 allowed-ips '10.2.0.0/24'
set interfaces wireguard wg01 peer to-wg02 address '192.168.0.142:12345'
set interfaces wireguard wg01 peer to-wg02 port '12345'
set interfaces wireguard wg01 peer to-wg02 pubkey 'XMrlPykaxhdAAiSjhtPlvi30NVkvLQliQuKP7AI7CyI='
set interfaces wireguard wg01 port '12345'
set protocols static interface-route 10.2.0.0/24 next-hop-interface wg01
The last step is to define an interface route for 10.2.0.0/24 to get
through the WireGuard interface `wg01`. Multiple IPs or networks can be
defined and routed, the last check is allowed-ips which either prevents
or allows the traffic.
To use a named key on an interface, the option private-key needs to be
set.
.. code-block:: none
set interfaces wireguard wg01 private-key KP01
set interfaces wireguard wg02 private-key KP02
The command ``run show wireguard keypairs pubkey KP01`` will then show
the public key, which needs to be shared with the peer.
**remote side**
.. code-block:: none
set interfaces wireguard wg01 address '10.2.0.1/24'
set interfaces wireguard wg01 description 'VPN-to-wg01'
set interfaces wireguard wg01 peer to-wg02 allowed-ips '10.1.0.0/24'
set interfaces wireguard wg01 peer to-wg02 address '192.168.0.124'
set interfaces wireguard wg01 peer to-wg02 port '12345'
set interfaces wireguard wg01 peer to-wg02 pubkey 'u41jO3OF73Gq1WARMMFG7tOfk7+r8o8AzPxJ1FZRhzk='
set interfaces wireguard wg01 port '12345'
set protocols static interface-route 10.1.0.0/24 next-hop-interface wg01
Assure that your firewall rules allow the traffic, in which case you
have a working VPN using WireGuard
.. code-block:: none
wg01# ping 10.2.0.1
PING 10.2.0.1 (10.2.0.1) 56(84) bytes of data.
64 bytes from 10.2.0.1: icmp_seq=1 ttl=64 time=1.16 ms
64 bytes from 10.2.0.1: icmp_seq=2 ttl=64 time=1.77 ms
wg02# ping 10.1.0.1
PING 10.1.0.1 (10.1.0.1) 56(84) bytes of data.
64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=4.40 ms
64 bytes from 10.1.0.1: icmp_seq=2 ttl=64 time=1.02 ms
An additional layer of symmetric-key crypto can be used on top of the
asymmetric crypto, which is optional.
.. code-block:: none
wg01# run generate wireguard preshared-key
rvVDOoc2IYEnV+k5p7TNAmHBMEGTHbPU8Qqg8c/sUqc=
Copy the key, as it is not stored on the local file system. Make sure
you distribute that key in a safe manner, it's a symmetric key, so only
you and your peer should have knowledge of its content.
.. code-block:: none
wg01# set interfaces wireguard wg01 peer to-wg02 preshared-key 'rvVDOoc2IYEnV+k5p7TNAmHBMEGTHbPU8Qqg8c/sUqc='
wg02# set interfaces wireguard wg01 peer to-wg01 preshared-key 'rvVDOoc2IYEnV+k5p7TNAmHBMEGTHbPU8Qqg8c/sUqc='
Road Warrior Example
--------------------
With WireGuard, a Road Warrior VPN config is similar to a site-to-site
VPN. It just lacks the ``address`` and ``port`` statements.
In the following example, the IPs for the remote clients are defined in
the peers. This would allow the peers to interact with one another.
.. code-block:: none
wireguard wg0 {
address 10.172.24.1/24
address 2001:DB8:470:22::1/64
description RoadWarrior
peer MacBook {
allowed-ips 10.172.24.30/32
allowed-ips 2001:DB8:470:22::30/128
persistent-keepalive 15
pubkey F5MbW7ye7DsoxdOaixjdrudshjjxN5UdNV+pGFHqehc=
}
peer iPhone {
allowed-ips 10.172.24.20/32
allowed-ips 2001:DB8:470:22::30/128
persistent-keepalive 15
pubkey BknHcLFo8nOo8Dwq2CjaC/TedchKQ0ebxC7GYn7Al00=
}
port 2224
}
The following is the config for the iPhone peer above. It's important to
note that the ``AllowedIPs`` setting directs all IPv4 and IPv6 traffic
through the connection.
.. code-block:: none
[Interface]
PrivateKey = ARAKLSDJsadlkfjasdfiowqeruriowqeuasdf=
Address = 10.172.24.20/24, 2001:DB8:470:22::20/64
DNS = 10.0.0.53, 10.0.0.54
[Peer]
PublicKey = RIbtUTCfgzNjnLNPQ/ulkGnnB2vMWHm7l2H/xUfbyjc=
AllowedIPs = 0.0.0.0/0, ::/0
Endpoint = 192.0.2.1:2224
PersistentKeepalive = 25
This MacBook peer is doing split-tunneling, where only the subnets local
to the server go over the connection.
.. code-block:: none
[Interface]
PrivateKey = 8Iasdfweirousd1EVGUk5XsT+wYFZ9mhPnQhmjzaJE6Go=
Address = 10.172.24.30/24, 2001:DB8:470:22::30/64
[Peer]
PublicKey = RIbtUTCfgzNjnLNPQ/ulkGnnB2vMWHm7l2H/xUfbyjc=
AllowedIPs = 10.172.24.30/24, 2001:DB8:470:22::/64
Endpoint = 192.0.2.1:2224
PersistentKeepalive = 25
Operational commands
====================
**Show interface status**
.. code-block:: none
vyos@wg01# run show interfaces wireguard wg01
interface: wg1
description: VPN-to-wg01
address: 10.2.0.1/24
public key: RIbtUTCfgzNjnLNPQ/asldkfjhaERDFl2H/xUfbyjc=
private key: (hidden)
listening port: 53665
peer: to-wg02
public key: u41jO3OF73Gq1WARMMFG7tOfk7+r8o8AzPxJ1FZRhzk=
latest handshake: 0:01:20
status: active
endpoint: 192.168.0.124:12345
allowed ips: 10.2.0.0/24
transfer: 42 GB received, 487 MB sent
persistent keepalive: every 15 seconds
RX:
bytes packets errors dropped overrun mcast
45252407916 31192260 0 244493 0 0
TX:
bytes packets errors dropped carrier collisions
511649780 5129601 24465 0 0 0
**Show public key of the default key**
.. code-block:: none
vyos@wg01# run show wireguard keypair pubkey default
FAXCPb6EbTlSH5200J5zTopt9AYXneBthAySPBLbZwM=
**Show public key of a named key**
.. code-block:: none
vyos@wg01# run show wireguard keypair pubkey KP01
HUtsu198toEnm1poGoRTyqkUKfKUdyh54f45dtcahDM=
**Delete wireguard keypairs**
.. code-block:: none
vyos@wg01# wireguard keypair default
|
