Age | Commit message (Collapse) | Author |
|
firewall: T6951: Add a configuration command for ethertypes that bridge firewalls should always accept
|
|
firewalls should always accept
|
|
journald
|
|
Previously, we used a lower limit of 1 and a default value of 32768 for the
nf_conntrack_buckets (conntrack hash-size) sysctl option. However, the Linux
kernel enforces an internal minimum of 1024. A configuration migrator will now
adjust the lower limit to 1024 if necessary.
The former default value of 32768 was passed as a kernel module option, which
only took effect after the second system reboot. This was due to the option being
rendered but not applied during the first boot. This behavior has been changed so
that the value is now configurable at runtime and takes effect immediately.
Additionally, since VyOS 1.4 increased the hardware requirements to 4GB of RAM,
we now align the default value of nf_conntrack_buckets with the kernel's
default for systems with more than 1GB of RAM to 65536 entries. Previously, we
only supported half that amount.
|
|
VyOS 1.4.1 implemented support for logging facilities for HAProxy. The
facilities got included from the syslog XML definition, which also added
"virtual" or non existing facilities in HAProxy, namely: all, authpriv and mark.
If any of the above facilities is set, HAProxy will not start.
The XML definition for syslog also came with an arbitrary log-level "all" that
is also unsupported in HAProxy.
This commit adds a migration script removing the illegal CLI nodes.
|
|
ids: T7241: remove Fastnetmon from the base system
|
|
It will eventually be moved to an addon
|
|
policy: T7116: Remove unsupported use of BGP community "internet"
|
|
* wlb: T7196: Migrate interface wildcards to nftables format
* wlb: T7196: Fix exclude/interface verify check
* wlb: T7196: Extra sanity check on ipv4 address function
|
|
This has been split into a separate commit in case this is overkill for
the fix. 1.2 and 1.3 installs predate the change to FRR that removed support,
but "internet" is already broken on 1.4.
|
|
LLDP is a stateless protocol which does not necessitate sending to receive
advertisements. There are multiple scenarios such as provider peering links in
which it is advantageous to receive LLDP but not disclose internal information
to the provider.
Add new CLI command:
* set service lldp interface <name> mode [disable|rx-tx|rx|tx]
The default is unchanged and will be rx-tx.
Furthermore if an interface has an explicit LLDP disable configured under
"set service lldp interface <name> disable" this will be migrated to
"set service lldp interface <name> mode disable"
|
|
* set protocols bgp address-family <ipv4-unicast|ipv6-unicast> redistribute
table <n> [metric <n>] [route-map <name>]
|
|
|
|
|
|
NHRP migration to FRR
|
|
interfaces attached to VRFs
|
|
|
|
Migrate "set protocols static route <x.x.x.x/x> next-hop <y.y.y.y> bfd multi-hop
source <z.z.z.z> profile <NAME>" to: "set protocols static route <x.x.x.x/x>
next-hop <y.y.y.y> bfd profile bar"
FRR supports only one source IP address per BFD multi-hop session. VyOS
had CLI cupport for multiple source addresses which made no sense.
|
|
- Fixed handling of flow isolation parameters.
- Corrected support for `nat` and `nonat` in flow isolation.
- Extended RTT values to cover the full range supported by `tc`.
- Make migration script 2-to-3 qos
|
|
|
|
|
|
|
|
|
|
|
|
OpenVPN CLI-option: T6571: rename ncp-ciphers with data-ciphers
|
|
(#3616)
* Change ipsec match-ipsec/none to match-ipsec-in and match-none-in for
fw rules
* Add ipsec match-ipsec-out and match-none-out
* Change all the points where the match-ipsec.xml.i include was used
before, making sure the new includes (match-ipsec-in/out.xml.i) are
used appropriately. There were a handful of spots where match-ipsec.xml.i
had snuck back in for output hooked chains already
(the common-rule-* includes)
* Add the -out generators to rendered templates
* Heavy modification to firewall config validators:
* I needed to check for ipsec-in matches no matter how deeply nested
under an output-hook chain(via jump-target) - this always generates
an error.
* Ended up retrofitting the jump-targets validator from root chains
and for named custom chains. It checks for recursive loops and improper
IPsec matches.
* Added "test_ipsec_metadata_match" and "test_cyclic_jump_validation"
smoketests
|
|
|
|
|
|
Wireless devices are subject to regulations issued by authorities. For any
given AP or router, there will most likely be no case where one wireless NIC is
located in one country and another wireless NIC in the same device is located
in another country, resulting in different regulatory domains to apply to the
same box.
Currently, wireless regulatory domains in VyOS need to be configured per-NIC:
set interfaces wireless wlan0 country-code us
This leads to several side-effects:
* When operating multiple WiFi NICs, they all can have different regulatory
domains configured which might offend legislation.
* Some NICs need additional entries to /etc/modprobe.d/cfg80211.conf to apply
regulatory domain settings, such as: "options cfg80211 ieee80211_regdom=US"
This is true for the Compex WLE600VX. This setting cannot be done
per-interface.
Migrate the first found wireless module country-code from the wireless
interface CLI to: "system wireless country-code"
|
|
|
|
T3900: Add support for raw tables in firewall
|
|
timeout parameters defined in conntrack to firewall global-opton section.
|
|
|
|
>=5.0
random - In kernel 5.0 and newer this is the same as fully-random. In earlier
kernels the port mapping will be randomized using a seeded MD5 hash mix using
source and destination address and destination port.
https://git.netfilter.org/nftables/commit/?id=fbe27464dee4588d906492749251454
|
|
pppoe-server: T6234: PPPoE-server pado-delay refactoring
|
|
|
|
|
|
to firewall global-optinos
|
|
Containers have the ability to add Linux system capabilities to them, this is
done using the "set container name <name> cap-add" command.
The CLI node sounds off and rather should be "set container name <name>
capability" instead as we use and pass a capability to a container and not
add/invent new ones.
|
|
dhcp-server high-availability>.
|
|
|
|
T6029: Rewritten Accel-PPP services to an identical feature set
|
|
Removed dhcp-interface option (l2tp)
Added wins-server (sstp)
Added description (ipoe, pppoe, sstp, pptp)
Added exteded-script (l2tp, sstp, pptp)
Added shaper (ipoe, pptp, sstp, l2tp)
Added limits (ipoe, pptp, sstp, l2tp)
Added snmp ( ipoe, pptp,sstp, l2tp)
Refactoring and reformated code.
|
|
connected interfaces
Prior dhcpd behaviour implicitly handled requests for locally connected subnets. Kea requires an explicit link between subnets and an interface.
|
|
T5960: Rewritten authentication node in PPTP to a single view
|
|
Rewritten authentication node in accel-ppp services
to a single view. In particular - PPTP authentication.
|
|
|
|
T5971: Rewritten ppp options in accel-ppp services
|
|
ddclient: T5966: Adjust dynamic dns config address subpath
|
|
Denied using command 'route-target vpn export/import'
with 'both' together in bgp configuration.
|