feat(swap): import .md files and webp transition from myst/current

Selective import from origin/myst/current (cf9c9b34):
- Add/update 255 .md files (full MyST conversion plus webp ref updates)
- Delete 175 PNG/JPG from docs/_static/images (webp twins already present)
- Delete 5 autotest topology.png (webp twins already present)

Preserved on swap (untouched):
- All .rst files (incremental swap pattern)
- conf.py, _ext/, _include/*.txt, .gitignore
- 115 canary md-*.md files
- 7 superpowers/specs/*.md design docs
- Logos vyos-logo.png / vyos-logo-icon.png (referenced by conf.py)

🤖 Generated by [robots](https://vyos.io)

1 files changed, 764 insertions, 0 deletions

diff --git a/docs/configuration/interfaces/bonding.md b/docs/configuration/interfaces/bonding.md
new file mode 100644
index 00000000..7a07a27c
--- /dev/null
+++ b/docs/configuration/interfaces/bonding.md
@@ -0,0 +1,764 @@
+---
+lastproofread: '2025-12-09'
+---
+
+(bond-interface)=
+
+# Bond / link aggregation
+
+A **bonding interface** aggregates multiple network interfaces into a single
+logical interface (referred to as a bond, {abbr}`LAG (Link Aggregation Group)`,
+EtherChannel, or port-channel).
+
+The behavior of a bonding interface depends on the selected mode. Modes provide
+either fault tolerance or a combination of load balancing and fault tolerance.
+Additionally, the bonding interface can be configured for link integrity
+monitoring.
+
+## Configuration
+
+### Common interface configuration
+
+```{cmdincludemd} /_include/interface-common-with-dhcp.txt
+:var0: bonding
+:var1: bond0
+```
+
+### Member interfaces
+
+```{cfgcmd} set interfaces bonding \<interface\> member interface \<member\>
+
+**Add an interface to the bonding group.**
+
+**Example:**
+
+To configure eth0 and eth1 as members of the bonding interface bond0, execute
+the following commands:
+```
+
+```none
+set interfaces bonding bond0 member interface eth0
+set interfaces bonding bond0 member interface eth1
+```
+
+### Bond modes
+
+````{cfgcmd} set interfaces bonding \<interface\> mode \<802.3ad | active-backup | broadcast | round-robin | transmit-load-balance | adaptive-load-balance | xor-hash\>
+
+```{eval-rst}
+**Configure the bonding mode on the interface. The default mode is**
+``802.3ad``.
+
+The available modes are:
+
+* ``802.3ad``
+
+.. list-table::
+   :widths: 20 80
+
+   * - **Description:**
+     - IEEE 802.3ad Dynamic Link Aggregation. Groups only member
+       interfaces with the same speed (e.g., 1 Gbps) and duplex
+       settings. Member interfaces with different speed and duplex
+       settings are not included in the active bond.
+
+       Provides load balancing and fault tolerance. Uses the
+       :abbr:`LACP (Link Aggregation Control Protocol)` to
+       negotiate the bond with the switch.
+   * - **Traffic distribution:**
+     - Traffic is distributed according to the **transmit hash
+       policy** (default: XOR).
+
+       The bonding driver applies an XOR operation to specific
+       packet header fields, generating a hash value that maps to
+       a particular member interface. This ensures the same network
+       flow is consistently transmitted over the same member
+       interface.
+
+       The transmit hash policy is configured via the ``hash-policy`` option.
+   * - **Failover:**
+     - If a member interface fails, the hash is recalculated to distribute
+       traffic among the remaining active member interfaces.
+
+.. note:: Not all transmit hash policies comply with 802.3ad, particularly
+   section 43.2.4. Using a non-compliant policy may result in out-of-order
+   packet delivery.
+
+* ``active-backup``
+
+.. list-table::
+   :widths: 20 80
+
+   * - **Description:**
+     - Provides fault tolerance. Only one member interface is active
+       at a time. Other member interfaces remain in a standby mode.
+   * - **Traffic distribution:**
+     - All traffic (incoming and outgoing) is routed via one active
+       member interface.
+   * - **Failover:**
+     - If the designated member interface fails, all traffic is
+       routed to another member interface. The bonding driver sends
+       a Gratuitous ARP to update the peer's MAC address table,
+       linking the bond's MAC address to another physical port.
+
+* ``broadcast``
+
+.. list-table::
+   :widths: 20 80
+
+   * - **Description:**
+     - Provides maximum fault tolerance by duplicating traffic.
+   * - **Traffic distribution:**
+     - Every packet is duplicated and transmitted on **all** member
+       interfaces.
+   * - **Failover:**
+     - Traffic flow is not interrupted as long as at least one
+       member interface remains active.
+
+* ``round-robin``
+
+.. list-table::
+   :widths: 20 80
+
+   * - **Description:**
+     - Provides load balancing and fault tolerance.
+   * - **Traffic distribution:**
+     - Packets are transmitted in sequential order across the member
+       interfaces (e.g., packet 1 > interface A, packet 2 >
+       interface B, etc.).
+   * - **Failover:**
+     - If a member interface fails, the sequence skips the failed
+       interface and continues with the remaining active members.
+
+* ``transmit-load-balance``
+
+.. list-table::
+   :widths: 20 80
+
+   * - **Description:**
+     - Provides adaptive transmit load balancing and fault tolerance.
+   * - **Traffic distribution:**
+     - **Outgoing:** Distributed across all active member interfaces
+       based on the current load.
+
+       **Incoming:** Received by a designated member interface
+       (active receiver).
+   * - **Failover:**
+     - If the active receiver fails, another member interface takes
+       over as the new active receiver.
+
+* ``adaptive-load-balance``
+
+.. list-table::
+   :widths: 20 80
+
+   * - **Description:**
+     - Provides adaptive transmit load balancing identical to
+       ``transmit-load-balance``, receive load balancing for IPv4
+       traffic, and fault tolerance for both incoming and outgoing
+       traffic.
+   * - **Traffic distribution:**
+     - **Outgoing:** Identical to ``transmit-load-balance``.
+
+       **Incoming:** Distributed based on ARP manipulation. For
+       both local and remote connections, the bonding driver
+       intercepts ARP traffic and changes the source MAC address
+       to the MAC address of the least loaded member interface.
+
+       All traffic from that peer is then routed to the chosen
+       member interface.
+   * - **Failover:**
+     - If a member interface's state changes (fails, recovers, is
+       added, or excluded), the traffic is redistributed among all
+       active member interfaces.
+
+* ``xor-hash``: Provides load balancing and fault tolerance
+  based on a hash formula. Distributes traffic and handles
+  failover identically to ``802.3ad``, but operates without
+  the :abbr:`LACP (Link Aggregation Control Protocol)`.
+```
+
+````
+
+```{cfgcmd} set interfaces bonding \<interface\> min-links \<0-16\>
+
+**Configure how many member interfaces must be active (in the
+link-up state) to mark the bonding interface UP (carrier
+asserted).**
+
+This command applies only when the bonding interface is configured
+in 802.3ad mode and functions like the Cisco EtherChannel min-links
+feature. It ensures that a bonding interface is marked UP (carrier
+asserted) only when a specified number of member interfaces are
+active (in the link-up state). This helps guarantee a minimum level
+of bandwidth for higher-level services (such as clustering) relying
+on the bonding interface.
+
+The default value is 0. This marks the bonding interface UP
+(carrier asserted) whenever an active LACP aggregator exists,
+regardless of the number of member interfaces in that aggregator.
+
+:::{note}
+In 802.3ad mode, a bond cannot be active without at least one active
+member interface. Therefore, setting min-links to 0 or 1 has the same result:
+the bonding interface is marked UP (carrier asserted).
+:::
+```
+
+```{cfgcmd} set interfaces bonding \<interface\> lacp-rate \<slow|fast\>
+
+**Configure the rate at which the bonding interface requests its link
+partner to send** {abbr}`LACPDUs (Link Aggregation Control Protocol Data
+Units)` **in 802.3ad mode.**
+
+This command applies only when the bonding interface is configured in
+802.3ad mode.
+
+The following options are available:
+
+* **slow (default):** Requests the link partner to transmit LACPDUs every 30 seconds.
+
+* **fast:** Requests the link partner to transmit LACPDUs every 1 second.
+```
+```{cfgcmd} set interfaces bonding \<interface\> system-mac \<mac address\>
+
+**Configure a specific MAC address for the bonding interface.**
+
+This sets the 802.3ad system MAC address, which is used for {abbr}`LACPDU (Link
+Aggregation Control Protocol Data Unit)` exchanges with the link partner.
+You can assign a fixed MAC address or generate a random one for these
+{abbr}`LACPDU (Link Aggregation Control Protocol Data Unit)` exchanges.
+```
+```{cfgcmd} set interfaces bonding \<interface\> hash-policy \<policy\>
+
+**Configure which transmit hash policy to use for distributing traffic across
+member interfaces.**
+
+The following policies are available:
+
+* ``layer2``
+
+**Description:** Routes all traffic destined for a specific network peer through
+the same member interface. The policy is 802.3ad-compliant.
+
+**Hash inputs:** Source MAC address, destination MAC address, and Ethernet packet
+type ID.
+
+**Formula:**
+
+:::{code-block} none
+hash = source MAC address XOR destination MAC address XOR packet type ID
+member interface number = hash modulo member interface count
+:::
+
+* ``layer2+3``
+
+**Description:** Similar to ``layer2``, routes all traffic destined for a specific
+network peer through the same member interface and is IEEE 802.3ad-compliant. Uses
+both Layer 2 and Layer 3 information to provide a more balanced traffic distribution.
+
+**Hash inputs:**
+* Source MAC address, destination MAC address, and Ethernet packet type ID.
+* Source IP address, destination IP address. IPv6 addresses are first hashed
+  using ``IPv6_addr_hash``.
+
+**Formula:**
+
+:::{code-block} none
+hash = source MAC address XOR destination MAC address XOR packet type ID
+hash = hash XOR source IP address XOR destination IP address
+hash = hash XOR (hash RSHIFT 16)
+hash = hash XOR (hash RSHIFT 8)
+member interface number = hash modulo member interface count
+:::
+
+For non-IP traffic, the formula is the same as for ``layer2``.
+
+* ``layer3+4``
+
+**Description:** Routes different connections (flows) destined for a specific
+network peer through multiple member interfaces, but ensures each individual
+flow is routed through only one member interface.
+
+:::{note}
+This policy is not fully 802.3ad-compliant. When a single TCP or UDP flow
+contains both fragmented and unfragmented packets, the algorithm may distribute
+them across different member interfaces. This may result in out-of-order packet
+delivery, violating the 802.3ad standard.
+:::
+
+**Hash inputs:**
+* Source port, destination port (if available).
+* Source IP address, destination IP address. IPv6 addresses are first hashed
+  using ``IPv6_addr_hash``.
+
+**Formula:**
+
+:::{code-block} none
+hash = source port, destination port (as in the header)
+hash = hash XOR source IP address XOR destination IP address
+hash = hash XOR (hash RSHIFT 16)
+hash = hash XOR (hash RSHIFT 8)
+member interface number = hash modulo member interface count
+:::
+
+For fragmented TCP or UDP packets and all other IPv4 and IPv6 traffic, the
+source and destination port information is omitted.
+
+For non-IP traffic, the formula is the same as for ``layer2``.
+```
+
+
+```{cfgcmd} set interfaces bonding \<interface\> primary \<interface\>
+
+**Configure the primary member interface in the bond.**
+
+The primary member interface remains active as long as it is operational;
+alternative member interfaces are used only if it fails.
+
+Use this configuration when a specific member interface is preferred,
+such as one with higher throughput.
+
+This command applies only to ``active-backup``, ``transmit-load-balance``, and
+``adaptive-load-balance`` modes.
+```
+
+
+```{cfgcmd} set interfaces bonding \<interface\> arp-monitor interval \<time\>
+
+**Configure the ARP monitoring interval, in seconds, for the bonding interface.**
+
+ARP monitoring periodically assesses the health of each member interface by
+checking whether it has recently sent or received traffic (this criterion
+varies depending on the bonding mode and the member interface’s state). ARP
+probes are sent to the IP addresses specified with the arp-monitor target option.
+
+When ARP monitoring is used with EtherChannel-compatible modes (such as
+``round-robin`` or ``xor-hash``), the switch should be configured to distribute
+traffic across all member interfaces. If the switch distributes traffic using
+an XOR-based policy, all ARP replies will be received on one member interface,
+causing other member interfaces to be incorrectly marked as failed.
+
+Setting this value to 0 disables ARP monitoring.
+
+The default value is 0.
+```
+
+
+```{cfgcmd} set interfaces bonding \<interface\> arp-monitor target \<address\>
+
+**Configure the IP addresses for ARP monitoring requests.**
+
+The bonding driver sends ARP requests to these IP addresses to check the
+state of member interfaces.
+
+To enable ARP monitoring, configure at least one IP address (up to 16 per
+bonding interface).
+
+By default, no IP addresses are configured.
+```
+
+### {abbr}`VLAN (Virtual Local Area Network)`
+
+```{cmdincludemd} /_include/interface-vlan-8021q.txt
+:var0: bonding
+:var1: bond0
+```
+
+### SPAN port mirroring
+
+```{cmdincludemd} ../../_include/interface-mirror.txt
+:var0: bonding
+:var1: bond1
+:var2: eth3
+```
+
+#### EVPN multihoming
+
+
+EVPN multihoming (EVPN-MH) is a standards-based solution (RFC 7432, RFC 8365)
+that enables Customer Edge (CE) devices, such as servers, to connect to two
+or more Provider Edge (PE) devices for redundancy and load balancing.
+
+
+EVPN-MH is often used as a modern, standards-based alternative to
+{abbr}`MLAG (Multi-Chassis Link Aggregation)` and {abbr}`VTEPs (Virtual
+Tunnel Endpoints)`.
+
+
+**Ethernet Segment (ES) and Ethernet Segment Identifier (ESI)**
+
+
+Physical links that connect a CE device to PE devices are bundled using link
+aggregation. This logical bundle is called an Ethernet Segment (ES) and is
+uniquely identified by an Ethernet Segment Identifier (ESI) within the
+EVPN domain.
+
+
+To enable EVPN-MH, configure the same ESI on the bonding interfaces of all
+PE devices connected to a single CE device.
+
+
+An ESI is configured by specifying either a system MAC address and a local
+discriminator, or an Ethernet Segment Identifier Name (ESINAME).
+
+
+The following two commands generate a 10-byte Type-3 ESI by combining the
+system MAC and local discriminator:
+
+```{cfgcmd} set interfaces bonding \<interface\> evpn es-id \<1-16777215|10-byte ID\>
+
+```
+```{cfgcmd} set interfaces bonding \<interface\> evpn es-sys-mac \<xx:xx:xx:xx:xx:xx\>
+
+Alternatively, assign an ESINAME directly as a 10-byte Type-0 ESI using the
+following format: 00:AA:BB:CC:DD:EE:FF:GG:HH:II.
+
+**BGP-EVPN route usage**
+
+EVPN-MH uses BGP-EVPN route types 1 and 2 for ES discovery and MAC-IP
+synchronization:
+
+* **Type 1 (EAD-per-ES and EAD-per-EVI)** routes advertise the locally
+attached ESs and discover remote ESs in the network.
+* **Type 2 (MAC-IP advertisement)** routes are advertised with a
+destination ESI, enabling MAC-IP synchronization between ES peers.
+```
+
+```{cfgcmd} set interfaces bonding \<interface\> evpn es-df-pref \<1-65535\>
+
+**Configure the** {abbr}`DF (Designated Forwarder)` **preference (1-65535) for
+the interface. A higher value indicates a higher preference to become the**
+{abbr}`DF (Designated Forwarder)`. **The** {abbr}`DF (Designated Forwarder)`
+**preference is configured per-ES.**
+
+The DF election process determines which interface in a specific ES forwards
+{abbr}`BUM (Broadcast, Unknown Unicast, and Multicast)` traffic from the EVPN
+overlay to the connected CE device. EVPN Type-4 (Ethernet Segment) routes are
+used to elect the DF, implementing the preference-based election method defined
+in RFC 9785.
+
+Interfaces not elected as the DF drop any BUM traffic from the EVPN overlay
+using non-DF filters. Similarly, traffic received from ES peers via the EVPN
+overlay is blocked from forwarding to the CE device to maintain split-horizon
+filtering with local bias.
+```
+
+```{cmdincludemd} /_include/interface-evpn-uplink.txt
+:var0: bonding
+:var1: bond0
+```
+
+## Example
+
+
+The following configuration example applies to all listed third-party vendors.
+It creates a bonding interface with two member interfaces, defines VLANs 10
+and 100 on the bonding interface, and assigns an IPv4 address to each VLAN
+subinterface.
+
+```none
+# Create the bonding interface bond0 with 802.3ad LACP
+set interfaces bonding bond0 hash-policy 'layer2'
+set interfaces bonding bond0 mode '802.3ad'
+
+# Add the required VLANs and IPv4 addresses on them
+set interfaces bonding bond0 vif 10 address 192.168.0.1/24
+set interfaces bonding bond0 vif 100 address 10.10.10.1/24
+
+# Add the member interfaces to the bonding interface
+set interfaces bonding bond0 member interface eth1
+set interfaces bonding bond0 member interface eth2
+```
+:::{note}
+If you are running this configuration in a virtual environment like
+EVE-NG, ensure the e1000 driver is chosen for your VyOS NIC. The default
+drivers, such as ``virtio-net-pci`` or ``vmxnet3``, are incompatible with
+this configuration. Specifically, ICMP messages will not be processed
+correctly.
+
+To check your NIC driver, use the following command:
+``show interfaces ethernet eth0 physical | grep -i driver``
+:::
+
+
+### Cisco Catalyst configuration
+
+
+Configure a Cisco Catalyst switch to integrate with a two-member VyOS bonding
+interface.
+
+
+Assign member interfaces to PortChannel:
+
+```none
+interface GigabitEthernet1/0/23
+ description VyOS eth1
+ channel-group 1 mode active
+!
+interface GigabitEthernet1/0/24
+ description VyOS eth2
+ channel-group 1 mode active
+!
+```
+
+A new interface, `Port-channel1`, becomes available; all configuration,
+such as allowed VLAN interfaces and STP, is applied here.
+
+```none
+interface Port-channel1
+ description LACP Channel for VyOS
+ switchport trunk encapsulation dot1q
+ switchport trunk allowed vlan 10,100
+ switchport mode trunk
+ spanning-tree portfast trunk
+!
+```
+
+### Juniper EX Switch configuration
+
+
+Configure a Juniper EX Series switch to integrate with a two-member VyOS bonding
+interface.
+
+```none
+# Create aggregated ethernet device with 802.3ad LACP and port speeds of 10gbit/s
+set interfaces ae0 aggregated-ether-options link-speed 10g
+set interfaces ae0 aggregated-ether-options lacp active
+
+# Create layer 2 on the aggregated ethernet device with trunking for our VLANs
+set interfaces ae0 unit 0 family ethernet-switching port-mode trunk
+
+# Add the required vlans to the device
+set interfaces ae0 unit 0 family ethernet-switching vlan members 10
+set interfaces ae0 unit 0 family ethernet-switching vlan members 100
+
+# Add the two interfaces to the aggregated ethernet device, in this setup both
+# ports are on the same switch (switch 0, module 1, port 0 and 1)
+set interfaces xe-0/1/0 ether-options 802.3ad ae0
+set interfaces xe-0/1/1 ether-options 802.3ad ae0
+
+# But this can also be done with multiple switches in a stack, a virtual
+# chassis on Juniper (switch 0 and switch 1, module 1, port 0 on both switches)
+set interfaces xe-0/1/0 ether-options 802.3ad ae0
+set interfaces xe-1/1/0 ether-options 802.3ad ae0
+```
+
+### Aruba/HP configuration
+
+
+Configure an Aruba/HP 2510G switch to integrate with a two-member VyOS bonding
+interface.
+
+```none
+# Create trunk with 2 member interfaces (interface 1 and 2) and LACP
+trunk 1-2 Trk1 LACP
+
+# Add the required VLANs to the trunk
+vlan 10 tagged Trk1
+vlan 100 tagged Trk1
+```
+
+### Arista EOS configuration
+
+
+When deploying VyOS in environments with Arista switches, use the following
+blueprint as an initial setup to configure an operational LACP port-channel
+between the two devices.
+
+
+Let's assume the following topology:
+
+
+```{eval-rst}
+.. figure:: /_static/images/vyos_arista_bond_lacp.webp
+   :alt: VyOS Arista EOS setup
+```
+
+
+**R1**
+
+```none
+interfaces {
+    bonding bond10 {
+        hash-policy layer3+4
+        member {
+            interface eth1
+            interface eth2
+        }
+        mode 802.3ad
+        vif 100 {
+            address 192.0.2.1/30
+            address 2001:db8::1/64
+        }
+    }
+```
+**R2**
+
+
+
+```none
+interfaces {
+    bonding bond10 {
+        hash-policy layer3+4
+        member {
+            interface eth1
+            interface eth2
+        }
+        mode 802.3ad
+        vif 100 {
+            address 192.0.2.2/30
+            address 2001:db8::2/64
+        }
+    }
+```
+**SW1**
+
+```none
+!
+vlan 100
+   name FOO
+!
+interface Port-Channel10
+   switchport trunk allowed vlan 100
+   switchport mode trunk
+   spanning-tree portfast
+!
+interface Port-Channel20
+   switchport mode trunk
+   no spanning-tree portfast auto
+   spanning-tree portfast network
+!
+interface Ethernet1
+   channel-group 10 mode active
+!
+interface Ethernet2
+   channel-group 10 mode active
+!
+interface Ethernet3
+   channel-group 20 mode active
+!
+interface Ethernet4
+   channel-group 20 mode active
+!
+```
+**SW2**
+
+
+
+```none
+!
+vlan 100
+   name FOO
+!
+interface Port-Channel10
+   switchport trunk allowed vlan 100
+   switchport mode trunk
+   spanning-tree portfast
+!
+interface Port-Channel20
+   switchport mode trunk
+   no spanning-tree portfast auto
+   spanning-tree portfast network
+!
+interface Ethernet1
+   channel-group 10 mode active
+!
+interface Ethernet2
+   channel-group 10 mode active
+!
+interface Ethernet3
+   channel-group 20 mode active
+!
+interface Ethernet4
+   channel-group 20 mode active
+!
+```
+:::{note}
+When testing this environment in EVE-NG, ensure the e1000 driver
+is chosen for your VyOS network interfaces. If the default virtio driver
+is used, VyOS will not transmit LACP PDUs, preventing the port-channel
+from ever becoming active.
+:::
+
+
+(operation)=
+
+## Operation
+
+```{opcmd} show interfaces bonding
+
+Show brief interface information.
+
+
+:::{code-block} none
+vyos@vyos:~$ show interfaces bonding
+Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
+Interface        IP Address                        S/L  Description
+---------        ----------                        ---  -----------
+bond0            -                                 u/u  my-sw1 int 23 and 24
+bond0.10         192.168.0.1/24                    u/u  office-net
+bond0.100        10.10.10.1/24                     u/u  management-net
+:::
+```
+```{opcmd} show interfaces bonding \<interface\>
+
+Show detailed interface information.
+
+:::{code-block} none
+vyos@vyos:~$ show interfaces bonding bond5
+bond5: <NO-CARRIER,BROADCAST,MULTICAST,MASTER,UP> mtu 1500 qdisc noqueue state DOWN group default qlen 1000
+    link/ether 00:50:56:bf:ef:aa brd ff:ff:ff:ff:ff:ff
+    inet6 fe80::e862:26ff:fe72:2dac/64 scope link tentative
+       valid_lft forever preferred_lft forever
+
+    RX:  bytes  packets  errors  dropped  overrun       mcast
+             0        0       0        0        0           0
+    TX:  bytes  packets  errors  dropped  carrier  collisions
+             0        0       0        0        0           0
+:::
+```
+```{opcmd} show interfaces bonding \<interface\> detail
+
+Show detailed information about the underlying physical links on the given
+bonding interface.
+
+:::{code-block} none
+vyos@vyos:~$ show interfaces bonding bond5 detail
+Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
+Bonding Mode: IEEE 802.3ad Dynamic link aggregation
+Transmit Hash Policy: layer2 (0)
+MII Status: down
+MII Polling Interval (ms): 100
+Up Delay (ms): 0
+Down Delay (ms): 0
+802.3ad info
+LACP rate: slow
+Min links: 0
+Aggregator selection policy (ad_select): stable
+Slave Interface: eth1
+MII Status: down
+Speed: Unknown
+Duplex: Unknown
+Link Failure Count: 0
+Permanent HW addr: 00:50:56:bf:ef:aa
+Slave queue ID: 0
+Aggregator ID: 1
+Actor Churn State: churned
+Partner Churn State: churned
+Actor Churned Count: 1
+Partner Churned Count: 1
+Slave Interface: eth2
+MII Status: down
+Speed: Unknown
+Duplex: Unknown
+Link Failure Count: 0
+Permanent HW addr: 00:50:56:bf:19:26
+Slave queue ID: 0
+Aggregator ID: 2
+Actor Churn State: churned
+Partner Churn State: churned
+Actor Churned Count: 1
+Partner Churned Count: 1
+:::
+```
\ No newline at end of file