diff options
Diffstat (limited to 'docs/configuration/protocols/pim.md')
| -rw-r--r-- | docs/configuration/protocols/pim.md | 18 |
1 files changed, 9 insertions, 9 deletions
diff --git a/docs/configuration/protocols/pim.md b/docs/configuration/protocols/pim.md index 30f3d49b..8a96691a 100644 --- a/docs/configuration/protocols/pim.md +++ b/docs/configuration/protocols/pim.md @@ -32,7 +32,7 @@ source-specific multicast). .. cfgcmd:: set protocols pim ecmp If PIM has the a choice of ECMP nexthops for a particular - {abbr}`RPF (Reverse Path Forwarding)`, PIM will cause S,G flows to be + :abbr:`RPF (Reverse Path Forwarding)`, PIM will cause S,G flows to be spread out amongst the nexthops. If this command is not specified then the first nexthop found will be used. ``` @@ -97,7 +97,7 @@ source-specific multicast). ```{eval-rst} .. cfgcmd:: set protocols pim rp <address> group <group> - In order to use PIM, it is necessary to configure a {abbr}`RP (Rendezvous Point)` + In order to use PIM, it is necessary to configure a :abbr:`RP (Rendezvous Point)` for join messages to be sent to. Currently the only methodology to do this is via static rendezvous point commands. @@ -111,8 +111,8 @@ source-specific multicast). .. cfgcmd:: set protocols pim rp keep-alive-timer <n> Modify the time out value for a S,G flow from 1-65535 seconds at - {abbr}`RP (Rendezvous Point)`. The normal keepalive period for the KAT(S,G) - defaults to 210 seconds. However, at the {abbr}`RP (Rendezvous Point)`, the + :abbr:`RP (Rendezvous Point)`. The normal keepalive period for the KAT(S,G) + defaults to 210 seconds. However, at the :abbr:`RP (Rendezvous Point)`, the keepalive period must be at least the Register_Suppression_Time, or the RP may time out the (S,G) state before the next Null-Register arrives. Thus, the KAT(S,G) is set to max(Keepalive_Period, RP_Keepalive_Period) @@ -121,7 +121,7 @@ source-specific multicast). If choosing a value below 31 seconds be aware that some hardware platforms cannot see data flowing in better than 30 second chunks. - See {rfc}`7761#section-4.1` for details. + See :rfc:`7761#section-4.1` for details. ``` ```{eval-rst} @@ -129,7 +129,7 @@ source-specific multicast). When sending PIM hello packets tell PIM to not send any v6 secondary addresses on the interface. This information is used to allow PIM to use v6 - nexthops in it's decision for {abbr}`RPF (Reverse Path Forwarding)` lookup + nexthops in it's decision for :abbr:`RPF (Reverse Path Forwarding)` lookup if this option is not set (default). ``` @@ -148,7 +148,7 @@ source-specific multicast). .. cfgcmd:: set protocols pim ssm prefix-list <list> Specify a range of group addresses via a prefix-list that forces PIM to never - do {abbr}`SSM (Source-Specific Multicast)` over. + do :abbr:`SSM (Source-Specific Multicast)` over. ``` ### Interface specific commands @@ -168,7 +168,7 @@ source-specific multicast). ```{eval-rst} .. cfgcmd:: set protocols pim interface <interface> dr-priority <n> - Set the {abbr}`DR (Designated Router)` Priority for the interface. + Set the :abbr:`DR (Designated Router)` Priority for the interface. This command is useful to allow the user to influence what node becomes the DR for a LAN segment. ``` @@ -241,7 +241,7 @@ source-specific multicast). Use this command to configure in the selected interface the IGMP query response timeout value (10-250) in deciseconds. If a report is not returned in the specified time, it will be assumed the (S,G) or - (\*,G) state {rfc}`7761#section-4.1` has timed out. + (\*,G) state :rfc:`7761#section-4.1` has timed out. ``` ```{eval-rst} |