diff options
Diffstat (limited to 'docs/configuration/protocols')
| -rw-r--r-- | docs/configuration/protocols/failover.rst | 9 | ||||
| -rw-r--r-- | docs/configuration/protocols/ospf.rst | 13 |
2 files changed, 11 insertions, 11 deletions
diff --git a/docs/configuration/protocols/failover.rst b/docs/configuration/protocols/failover.rst index 8088e104..651fc5c3 100644 --- a/docs/configuration/protocols/failover.rst +++ b/docs/configuration/protocols/failover.rst @@ -3,7 +3,7 @@ Failover ######## Failover routes are manually configured routes, but they only install -to the routing table if the health-check target is alive. +to the routing table as kernel routes if the health-check target is alive. If the target is not alive the route is removed from the routing table until the target becomes available. @@ -28,7 +28,12 @@ Failover Routes .. cfgcmd:: set protocols failover route <subnet> next-hop <address> check type <protocol> - Defines protocols for checking ARP, ICMP, TCP + Defines protocols for checking ARP, ICMP, TCP. +* ICMP probe sends 2 ICMP request packets with a response timeout of 1 second. + If one ICMP response is received, the health check is successful. +* ARP probe sends 2 ARP requests with a response timeout of 1 second. + If one response is received, the health check is successful. +* TCP probe checks whether the destination port is open. Default is ``icmp``. diff --git a/docs/configuration/protocols/ospf.rst b/docs/configuration/protocols/ospf.rst index 9891c77d..ac0ed160 100644 --- a/docs/configuration/protocols/ospf.rst +++ b/docs/configuration/protocols/ospf.rst @@ -1341,9 +1341,8 @@ A typical configuration using 2 nodes. show ipv6 ospfv3 redistribute -.. note:: You cannot easily redistribute IPv6 routes via OSPFv3 on a - WireGuard interface link. This requires you to configure link-local - addresses manually on the WireGuard interfaces, see :vytask:`T1483`. +Cost calculation wireguard interfaces is unreliable as ospfv3 uses the link speed to calculate the link cost. +You might therefore want to set the link cost to a fixed value on WireGuard tunnels. Example configuration for WireGuard interfaces: @@ -1351,30 +1350,26 @@ Example configuration for WireGuard interfaces: .. code-block:: none - set interfaces wireguard wg01 address 'fe80::216:3eff:fe51:fd8c/64' - set interfaces wireguard wg01 address '192.168.0.1/24' set interfaces wireguard wg01 peer ospf02 allowed-ips '::/0' - set interfaces wireguard wg01 peer ospf02 allowed-ips '0.0.0.0/0' set interfaces wireguard wg01 peer ospf02 endpoint '10.1.1.101:12345' set interfaces wireguard wg01 peer ospf02 pubkey 'ie3...=' set interfaces wireguard wg01 port '12345' set protocols ospfv3 parameters router-id 192.168.1.1 set protocols ospfv3 interface 'wg01' area 0.0.0.0 + set protocols ospfv3 interface 'wg01' cost 10 set protocols ospfv3 interface 'lo' area 0.0.0.0 **Node 2** .. code-block:: none - set interfaces wireguard wg01 address 'fe80::216:3eff:fe0a:7ada/64' - set interfaces wireguard wg01 address '192.168.0.2/24' set interfaces wireguard wg01 peer ospf01 allowed-ips '::/0' - set interfaces wireguard wg01 peer ospf01 allowed-ips '0.0.0.0/0' set interfaces wireguard wg01 peer ospf01 endpoint '10.1.1.100:12345' set interfaces wireguard wg01 peer ospf01 pubkey 'NHI...=' set interfaces wireguard wg01 port '12345' set protocols ospfv3 parameters router-id 192.168.1.2 set protocols ospfv3 interface 'wg01' area 0.0.0.0 + set protocols ospfv3 interface 'wg01' cost 10 set protocols ospfv3 interface 'lo' area 0.0.0.0 **Status** |