diff options
Diffstat (limited to 'docs/configuration/service/pppoe-server.rst')
| -rw-r--r-- | docs/configuration/service/pppoe-server.rst | 59 |
1 files changed, 23 insertions, 36 deletions
diff --git a/docs/configuration/service/pppoe-server.rst b/docs/configuration/service/pppoe-server.rst index 3a0adee7..a230d9fe 100644 --- a/docs/configuration/service/pppoe-server.rst +++ b/docs/configuration/service/pppoe-server.rst @@ -57,48 +57,35 @@ Client Address Pools -------------------- To automatically assign the client an IP address as tunnel endpoint, a -client IP pool is needed. The source can be either RADIUS or a local -subnet or IP range definition. - -Once the local tunnel endpoint ``set service pppoe-server gateway-address -'10.1.1.2'`` has been defined, the client IP pool can be either defined -as a range or as subnet using CIDR notation. If the CIDR notation is -used, multiple subnets can be setup which are used sequentially. +client IP pool is needed. The source can be either RADIUS or a +named pool. There is possibility to create multiple named pools. +Each named pool can include only one address range. To use multiple +address ranges configure ``next-pool`` option. **Client IP address via IP range definition** -.. cfgcmd:: set service pppoe-server client-ip-pool start <address> - - Use this command to define the first IP address of a pool of - addresses to be given to PPPoE clients. It must be within a /24 - subnet. - -.. cfgcmd:: set service pppoe-server client-ip-pool stop <address> - - Use this command to define the last IP address of a pool of - addresses to be given to PPPoE clients. It must be within a /24 - subnet. - -.. code-block:: none +.. cfgcmd:: set service pppoe-server client-ip-pool <POOL-NAME> range <x.x.x.x-x.x.x.x | x.x.x.x/x> - set service pppoe-server client-ip-pool start '10.1.1.100' - set service pppoe-server client-ip-pool stop '10.1.1.111' + Use this command to define the IP address range to be given + to PPPoE clients. If notation ``x.x.x.x-x.x.x.x``, + it must be within a /24 subnet. If notation ``x.x.x.x/x`` is + used there is possibility to set host/netmask. +.. cfgcmd:: set service pppoe-server client-ip-pool <POOL-NAME> next-pool <NEXT-POOL-NAME> -**Client IP subnets via CIDR notation** + Use this command to define the next address pool name. -.. cfgcmd:: set service pppoe-server client-ip-pool subnet <address> +.. cfgcmd:: set service pppoe-server default-pool <POOL-NAME> - Use this command for every pool of client IP addresses you want to - define. The addresses of this pool will be given to PPPoE clients. - You must use CIDR notation. + Use this command to define default address pool name. .. code-block:: none - set service pppoe-server client-ip-pool subnet '10.1.1.0/24' - set service pppoe-server client-ip-pool subnet '10.1.2.0/23' - set service pppoe-server client-ip-pool subnet '10.1.4.0/22' + set service pppoe-server client-ip-pool IP-POOL next-pool 'IP-POOL2' + set service pppoe-server client-ip-pool IP-POOL range '10.0.10.5/24' + set service pppoe-server client-ip-pool IP-POOL2 range '10.0.0.10-10.0.0.12' + set service pppoe-server default-pool 'IP-POOL' **RADIUS based IP pools (Framed-IP-Address)** @@ -213,8 +200,8 @@ For Local Users set service pppoe-server authentication local-users username foo rate-limit download '20480' set service pppoe-server authentication local-users username foo rate-limit upload '10240' set service pppoe-server authentication mode 'local' - set service pppoe-server client-ip-pool start '10.1.1.100' - set service pppoe-server client-ip-pool stop '10.1.1.111' + set service pppoe-server client-ip-pool IP-POOL range '10.1.1.100/24' + set service pppoe-server default-pool 'IP-POOL' set service pppoe-server name-server '10.100.100.1' set service pppoe-server name-server '10.100.200.1' set service pppoe-server interface 'eth1' @@ -367,8 +354,8 @@ address from the pool 10.1.1.100-111, terminates at the local endpoint set service pppoe-server access-concentrator 'ACN' set service pppoe-server authentication local-users username foo password 'bar' set service pppoe-server authentication mode 'local' - set service pppoe-server client-ip-pool start '10.1.1.100' - set service pppoe-server client-ip-pool stop '10.1.1.111' + set service pppoe-server client-ip-pool IP-POOL range '10.1.1.100-10.1.1.111' + set service pppoe-server default-pool 'IP-POOL' set service pppoe-server interface eth1 set service pppoe-server gateway-address '10.1.1.2' set service pppoe-server name-server '10.100.100.1' @@ -385,8 +372,8 @@ The example below covers a dual-stack configuration via pppoe-server. set service pppoe-server authentication local-users username test password 'test' set service pppoe-server authentication mode 'local' - set service pppoe-server client-ip-pool start '192.168.0.1' - set service pppoe-server client-ip-pool stop '192.168.0.10' + set service pppoe-server client-ip-pool IP-POOL range '192.168.0.1/24' + set service pppoe-server default-pool 'IP-POOL' set service pppoe-server client-ipv6-pool delegate '2001:db8:8003::/48' delegation-prefix '56' set service pppoe-server client-ipv6-pool prefix '2001:db8:8002::/48' mask '64' set service pppoe-server ppp-options ipv6 allow |