diff options
Diffstat (limited to 'docs/troubleshooting.rst')
| -rw-r--r-- | docs/troubleshooting.rst | 34 |
1 files changed, 17 insertions, 17 deletions
diff --git a/docs/troubleshooting.rst b/docs/troubleshooting.rst index 6448d031..c8585f12 100644 --- a/docs/troubleshooting.rst +++ b/docs/troubleshooting.rst @@ -15,7 +15,7 @@ commands. The options for each are shown (the options for each command were displayed using the built-in help as described in the :ref:`cli` section and are omitted from the output here): -.. code-block:: sh +.. code-block:: console vyos@vyos:~$ ping Possible completions: @@ -25,7 +25,7 @@ section and are omitted from the output here): Several options are available when more extensive troubleshooting is needed: -.. code-block:: sh +.. code-block:: console vyos@vyos:~$ ping 8.8.8.8 Possible completions: @@ -51,7 +51,7 @@ Several options are available when more extensive troubleshooting is needed: ttl verbose -.. code-block:: sh +.. code-block:: console vyos@vyos:~$ traceroute Possible completions: @@ -64,7 +64,7 @@ Several options are available when more extensive troubleshooting is needed: However, another tool, mtr_, is available which combines ping and traceroute into a single tool. An example of its output is shown: -.. code-block:: sh +.. code-block:: console vyos@vyos:~$ mtr 10.62.212.12 @@ -95,7 +95,7 @@ It's possible to monitor network traffic, either at the flow level or protocol level. This can be useful when troubleshooting a variety of protocols and configurations. The following interface types can be monitored: -.. code-block:: sh +.. code-block:: console vyos@vyos:~$ monitor interfaces Possible completions: @@ -117,7 +117,7 @@ To monitor traffic flows, issue the :code:`monitor interfaces <type> <name> flow command, replacing `<type>` and `<name>` with your desired interface type and name, respectively. Output looks like the following: -.. code-block:: sh +.. code-block:: console 12.5Kb 25.0Kb 37.5Kb 50.0Kb 62.5Kb ???????????????????????????????????????????????????????????????????????????????????????????????????? @@ -145,7 +145,7 @@ traffic` command, replacing `<type>` and `<name>` with your desired interface type and name, respectively. This command invokes the familiar tshark_ utility and the following options are available: -.. code-block:: sh +.. code-block:: console vyos@vyos:~$ monitor interfaces ethernet eth0 traffic Possible completions: @@ -170,13 +170,13 @@ Interface Bandwith to take a quick view on the used bandwith of an interface use the ``monitor bandwith`` command -.. code-block:: sh +.. code-block:: console vyos@vyos:~$ monitor bandwidth interface eth0 show the following: -.. code-block:: sh +.. code-block:: console B (RX Bytes/second) 198.00 .|....|..................................................... @@ -202,7 +202,7 @@ Interface performance To take a look on the network bandwith between two nodes, the ``monitor bandwidth-test`` command is used to run iperf. -.. code-block:: sh +.. code-block:: console vyos@vyos:~$ monitor bandwidth-test Possible completions: @@ -212,7 +212,7 @@ bandwidth-test`` command is used to run iperf. * The ``accept`` command open a listen iperf server on TCP Port 5001 * The ``initiate`` command conncet to this server. -.. code-block:: sh +.. code-block:: console vyos@vyos:~$ monitor bandwidth-test initiate Possible completions: @@ -229,14 +229,14 @@ a continuously refreshed output. The command is run and output every 2 seconds, allowing you to monitor the output continuously without having to re-run the command. This can be useful to follow routing adjacency formation. -.. code-block:: sh +.. code-block:: console vyos@router:~$ monitor command "show interfaces" Will clear the screen and show you the output of ``show interfaces`` every 2 seconds. -.. code-block:: sh +.. code-block:: console Every 2.0s: /opt/vyatta/bin/vyatta-op-cmd-wrapper Sun Mar 26 02:49:46 2019 @@ -259,13 +259,13 @@ To do this use the ``clear`` command in Operational mode. to clear the console output -.. code-block:: sh +.. code-block:: console vyos@vyos:~$ clear console to clear interface counters -.. code-block:: sh +.. code-block:: console # clear all interfaces vyos@vyos:~$ clear interface ethernet counters @@ -274,7 +274,7 @@ to clear interface counters The command follow the same logic as the ``set`` command in configuration mode. -.. code-block:: sh +.. code-block:: console # clear all counters of a interface type vyos@vyos:~$ clear interface <interface_type> counters @@ -284,7 +284,7 @@ The command follow the same logic as the ``set`` command in configuration mode. to clear counters on firewall rulesets or single rules -.. code-block:: sh +.. code-block:: console vyos@vyos:~$ clear firewall name <ipv4 ruleset name> counters vyos@vyos:~$ clear firewall name <ipv4 ruleset name> rule <rule#> counters |