diff options
Diffstat (limited to 'docs')
| -rw-r--r-- | docs/installation/bare-metal.rst | 90 |
1 files changed, 22 insertions, 68 deletions
diff --git a/docs/installation/bare-metal.rst b/docs/installation/bare-metal.rst index 6578f84e..be5f9342 100644 --- a/docs/installation/bare-metal.rst +++ b/docs/installation/bare-metal.rst @@ -10,8 +10,8 @@ Supermicro A2SDi (Atom C3000) I opted to get one of the new Intel Atom C3000 CPUs to spawn VyOS on it. Running VyOS on an UEFI only device is supported as of VyOS release 1.2. -Shopping Cart -------------- +Supermicro Shopping Cart +------------------------ * 1x Supermicro CSE-505-203B (19" 1U chassis, inkl. 200W PSU) * 1x Supermicro MCP-260-00085-0B (I/O Shield for A2SDi-2C-HLN4F) @@ -95,8 +95,8 @@ The board can be powered via 12V from the front or via a 5V onboard connector. .. _vyos-on-baremetal:apu4_shopping: -Shopping Cart -------------- +APU4 Shopping Cart +------------------ * 1x apu4c4 = 4 i211AT LAN / AMD GX-412TC CPU / 4 GB DRAM / dual SIM * 1x Kingston SUV500MS/120G @@ -131,7 +131,7 @@ have been tested successfully on this Hardware platform using VyOS 1.3 * Sierra Wireless AirPrime MC7710 miniPCIe card (LTE) * Huawei ME909u-521 miniPCIe card (LTE) -VyOS 1.2 (crux) +VyOS 1.4 (sagitta) --------------- Depending on the VyOS versions you intend to install there is a difference in @@ -162,7 +162,6 @@ Set terminal emulator to 115200 8N1. .. start_vyoslinter - Now boot from the ``USB MSC Drive Generic Flash Disk 8.07`` media by pressing ``2``, the VyOS boot menu will appear, just wait 10 seconds or press ``Enter`` to continue. @@ -172,8 +171,9 @@ to continue. lqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk x VyOS - Boot Menu x tqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqu - x Live (amd64-vyos) x - x Live (amd64-vyos failsafe) x + x Live system (amd64-vyos) x + x Live system (amd64-vyos fail-safe mode) x + x Live system (amd64-vyos) - Serial console x x x mqqqqqqPress ENAutomatic boot in 10 seconds...nu entryqqqqqqqj @@ -183,14 +183,7 @@ The image will be loaded and the last lines you will get will be: Loading /live/vmlinuz... ok Loading /live/initrd.img... - -The Kernel will now spin up using a different console setting. Set terminal -emulator to 9600 8N1 and after a while your console will show: - -.. code-block:: none - - Loading /live/vmlinuz... ok - Loading /live/initrd.img... + ... Welcome to VyOS - vyos ttyS0 vyos login: @@ -198,36 +191,6 @@ emulator to 9600 8N1 and after a while your console will show: You can now proceed with a regular image installation as described in :ref:`installation`. -As the APU board itself still used a serial setting of 115200 8N1 it is -strongly recommended that you change the VyOS serial interface settings after -your first successful boot. - -Use the following command to adjust the :ref:`serial-console` settings: - -.. code-block:: none - - set system console device ttyS0 speed 115200 - -.. note:: Once you ``commit`` the above changes access to the serial interface - is lost until you set your terminal emulator to 115200 8N1 again. - -.. code-block:: none - - vyos@vyos# show system console - device ttyS0 { - speed 115200 - } - -VyOS 1.2 (rolling) ------------------- - -Installing the rolling release on an APU2 board does not require any change -on the serial console from your host side as :vytask:`T1327` was successfully -implemented. - -Simply proceed with a regular image installation as described in -:ref:`installation`. - .. _vyos-on-baremetal:apu4_pictures: Pictures @@ -406,19 +369,7 @@ Reboot into BIOS, Chipset > South Bridge > USB Configuration: * Disable XHCI * Enable USB 2.0 (EHCI) Support -Install VyOS: -------------- - -Create a VyOS bootable USB key. I used the 64-bit ISO (VyOS 1.1.7) and -`LinuxLive USB Creator <http://www.linuxliveusb.com/>`_. - -I'm not sure if it helps the process but I changed default option to live-serial -(line “default xxxx”) on the USB key under syslinux/syslinux.cfg. - -I connected the key to one black USB port on the back and powered on. The first -VyOS screen has some readability issues. Press :kbd:`Enter` to continue. - -Then VyOS should boot and you can perform the ``install image`` +Perform Image installation using `install image` CLI command. .. _gowin_gw-fn-1ur1-10g: @@ -436,8 +387,8 @@ In addition there is a Mellanox ConnectX-3 2* 10GbE SFP+ NIC available. **NOTE:** This is the entry level platform. Other derivates exists with i3-N305 CPU and 2x 25GbE! -Shopping Cart -------------- +Gowin Shopping Cart +------------------- * 1x Gowin GW-FN-1UR1-10G * 2x 128GB M.2 NVMe SSDs @@ -445,7 +396,8 @@ Shopping Cart Optional (WiFi + WWAN) ---------------------- -* 1x MediaTek 7921E M.2 NGFF WIFI module (not tested as this currently leads to a Kernel crash) +* 1x MediaTek 7921E M.2 NGFF WIFI module (not tested as this currently leads to + a Kernel crash) * 1x HP LT4120 Snapdragon X5 LTE WWAN module Pictures @@ -506,11 +458,13 @@ See interface description for more detailed mapping. VyOS 1.4 (sagitta) ^^^^^^^^^^^^^^^^^^ -Connect serial port to a PC through a USB <-> RJ45 console cable. Set terminal emulator -to 115200 8N1. You can also perform the installation using VGA or HDMI ports. +Connect serial port to a PC through a USB <-> RJ45 console cable. Set terminal +emulator to 115200 8N1. You can also perform the installation using VGA or HDMI +ports. -In this example I choose to install VyOS as RAID-1 on both NVMe drives. However, a previous -installation on the 128GB eMMC storage worked without any issues, too. +In this example I choose to install VyOS as RAID-1 on both NVMe drives. However, +a previous installation on the 128GB eMMC storage worked without any issues, +too. .. code-block:: none @@ -518,8 +472,8 @@ installation on the 128GB eMMC storage worked without any issues, too. vyos login: -Perform Image installation using `install image` CLI command. This installation uses two 128GB NVMe -disks setup as RAID1. +Perform Image installation using `install image` CLI command. This installation +uses two 128GB NVMe disks setup as RAID1. .. code-block:: none |