1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
|
.. _ipsec:
#####
IPsec
#####
:abbr:`GRE (Generic Routing Encapsulation)`, GRE/IPsec (or IPIP/IPsec,
SIT/IPsec, or any other stateless tunnel protocol over IPsec) is the usual way
to protect the traffic inside a tunnel.
An advantage of this scheme is that you get a real interface with its own
address, which makes it easier to setup static routes or use dynamic routing
protocols without having to modify IPsec policies. The other advantage is that
it greatly simplifies router to router communication, which can be tricky with
plain IPsec because the external outgoing address of the router usually doesn't
match the IPsec policy of typical site-to-site setup and you need to add special
configuration for it, or adjust the source address for outgoing traffic of your
applications. GRE/IPsec has no such problem and is completely transparent for
the applications.
GRE/IPIP/SIT and IPsec are widely accepted standards, which make this scheme
easy to implement between VyOS and virtually any other router.
For simplicity we'll assume that the protocol is GRE, it's not hard to guess
what needs to be changed to make it work with a different protocol. We assume
that IPsec will use pre-shared secret authentication and will use AES128/SHA1
for the cipher and hash. Adjust this as necessary.
.. NOTE:: VMware users should ensure that a VMXNET3 adapter is used. E1000
adapters have known issues with GRE processing.
*************************
IPsec policy matching GRE
*************************
The first and arguably cleaner option is to make your IPsec policy match GRE
packets between external addresses of your routers. This is the best option if
both routers have static external addresses.
Suppose the LEFT router has external address 192.0.2.10 on its eth0 interface,
and the RIGHT router is 203.0.113.45
On the LEFT:
.. code-block:: none
# GRE tunnel
set interfaces tunnel tun0 encapsulation gre
set interfaces tunnel tun0 local-ip 192.0.2.10
set interfaces tunnel tun0 remote-ip 203.0.113.45
set interfaces tunnel tun0 address 10.10.10.1/30
## IPsec
set vpn ipsec ipsec-interfaces interface eth0
# IKE group
set vpn ipsec ike-group MyIKEGroup proposal 1 dh-group '2'
set vpn ipsec ike-group MyIKEGroup proposal 1 encryption 'aes128'
set vpn ipsec ike-group MyIKEGroup proposal 1 hash 'sha1'
# ESP group
set vpn ipsec esp-group MyESPGroup proposal 1 encryption 'aes128'
set vpn ipsec esp-group MyESPGroup proposal 1 hash 'sha1'
# IPsec tunnel
set vpn ipsec site-to-site peer 203.0.113.45 authentication mode pre-shared-secret
set vpn ipsec site-to-site peer 203.0.113.45 authentication pre-shared-secret MYSECRETKEY
set vpn ipsec site-to-site peer 203.0.113.45 ike-group MyIKEGroup
set vpn ipsec site-to-site peer 203.0.113.45 default-esp-group MyESPGroup
set vpn ipsec site-to-site peer 203.0.113.45 local-address 192.0.2.10
# This will match all GRE traffic to the peer
set vpn ipsec site-to-site peer 203.0.113.45 tunnel 1 protocol gre
On the RIGHT, setup by analogy and swap local and remote addresses.
Source tunnel from loopbacks
^^^^^^^^^^^^^^^^^^^^^^^^^^^^
The scheme above doesn't work when one of the routers has a dynamic external
address though. The classic workaround for this is to setup an address on a
loopback interface and use it as a source address for the GRE tunnel, then setup
an IPsec policy to match those loopback addresses.
We assume that the LEFT router has static 192.0.2.10 address on eth0, and the
RIGHT router has a dynamic address on eth0.
**Setting up the GRE tunnel**
On the LEFT:
.. code-block:: none
set interfaces loopback lo address 192.168.99.1/32
set interfaces tunnel tun0 encapsulation gre
set interfaces tunnel tun0 address 10.10.10.1/30
set interfaces tunnel tun0 local-ip 192.168.99.1
set interfaces tunnel tun0 remote-ip 192.168.99.2
On the RIGHT:
.. code-block:: none
set interfaces loopback lo address 192.168.99.2/32
set interfaces tunnel tun0 encapsulation gre
set interfaces tunnel tun0 address 10.10.10.2/30
set interfaces tunnel tun0 local-ip 192.168.99.2
set interfaces tunnel tun0 remote-ip 192.168.99.1
**Setting up IPSec**
However, now you need to make IPsec work with dynamic address on one side. The
tricky part is that pre-shared secret authentication doesn't work with dynamic
address, so we'll have to use RSA keys.
First, on both routers run the operational command "generate pki key-pair
install <key-pair nam>>". You may choose different length than 2048 of course.
.. code-block:: none
vyos@left# run generate pki key-pair install ipsec-LEFT
Enter private key type: [rsa, dsa, ec] (Default: rsa)
Enter private key bits: (Default: 2048)
Note: If you plan to use the generated key on this router, do not encrypt the private key.
Do you want to encrypt the private key with a passphrase? [y/N] N
Configure mode commands to install key pair:
Do you want to install the public key? [Y/n] Y
set pki key-pair ipsec-LEFT public key 'MIIBIjANBgkqh...'
Do you want to install the private key? [Y/n] Y
set pki key-pair ipsec-LEFT private key 'MIIEvgIBADAN...'
[edit]
Configuration commands will display.
Note the command with the public key
(set pki key-pair ipsec-LEFT public key 'MIIBIjANBgkqh...').
Then do the same on the opposite router:
.. code-block:: none
vyos@left# run generate pki key-pair install ipsec-RIGHT
Note the command with the public key
(set pki key-pair ipsec-RIGHT public key 'FAAOCAQ8AMII...').
Now the noted public keys should be entered on the opposite routers.
On the LEFT:
.. code-block:: none
set pki key-pair ipsec-RIGHT public key 'FAAOCAQ8AMII...'
On the RIGHT:
.. code-block:: none
set pki key-pair ipsec-LEFT public key 'MIIBIjANBgkqh...'
Now you are ready to setup IPsec. You'll need to use an ID instead of address
for the peer.
On the LEFT (static address):
.. code-block:: none
set vpn ipsec interface eth0
set vpn ipsec esp-group MyESPGroup proposal 1 encryption aes128
set vpn ipsec esp-group MyESPGroup proposal 1 hash sha1
set vpn ipsec ike-group MyIKEGroup proposal 1 dh-group 2
set vpn ipsec ike-group MyIKEGroup proposal 1 encryption aes128
set vpn ipsec ike-group MyIKEGroup proposal 1 hash sha1
set vpn ipsec site-to-site peer @RIGHT authentication id LEFT
set vpn ipsec site-to-site peer @RIGHT authentication mode rsa
set vpn ipsec site-to-site peer @RIGHT authentication rsa local-key ipsec-LEFT
set vpn ipsec site-to-site peer @RIGHT authentication rsa remote-key ipsec-RIGHT
set vpn ipsec site-to-site peer @RIGHT authentication remote-id RIGHT
set vpn ipsec site-to-site peer @RIGHT default-esp-group MyESPGroup
set vpn ipsec site-to-site peer @RIGHT ike-group MyIKEGroup
set vpn ipsec site-to-site peer @RIGHT local-address 192.0.2.10
set vpn ipsec site-to-site peer @RIGHT connection-type respond
set vpn ipsec site-to-site peer @RIGHT tunnel 1 local prefix 192.168.99.1/32 # Additional loopback address on the local
set vpn ipsec site-to-site peer @RIGHT tunnel 1 remote prefix 192.168.99.2/32 # Additional loopback address on the remote
On the RIGHT (dynamic address):
.. code-block:: none
set vpn ipsec interface eth0
set vpn ipsec esp-group MyESPGroup proposal 1 encryption aes128
set vpn ipsec esp-group MyESPGroup proposal 1 hash sha1
set vpn ipsec ike-group MyIKEGroup proposal 1 dh-group 2
set vpn ipsec ike-group MyIKEGroup proposal 1 encryption aes128
set vpn ipsec ike-group MyIKEGroup proposal 1 hash sha1
set vpn ipsec site-to-site peer 192.0.2.10 authentication id RIGHT
set vpn ipsec site-to-site peer 192.0.2.10 authentication mode rsa
set vpn ipsec site-to-site peer 192.0.2.10 authentication rsa local-key ipsec-RIGHT
set vpn ipsec site-to-site peer 192.0.2.10 authentication rsa remote-key ipsec-LEFT
set vpn ipsec site-to-site peer 192.0.2.10 authentication remote-id LEFT
set vpn ipsec site-to-site peer 192.0.2.10 connection-type initiate
set vpn ipsec site-to-site peer 192.0.2.10 default-esp-group MyESPGroup
set vpn ipsec site-to-site peer 192.0.2.10 ike-group MyIKEGroup
set vpn ipsec site-to-site peer 192.0.2.10 local-address any
set vpn ipsec site-to-site peer 192.0.2.10 tunnel 1 local prefix 192.168.99.2/32 # Additional loopback address on the local
set vpn ipsec site-to-site peer 192.0.2.10 tunnel 1 remote prefix 192.168.99.1/32 # Additional loopback address on the remote
|
