1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
|
.. _size2site_ipsec:
Site-to-Site
============
Site-to-site mode provides a way to add remote peers, which could be configured to exchange encrypted information between them and VyOS itself or connected/routed networks.
To configure site-to-site connection you need to add peers with the ``set vpn ipsec site-to-site`` command.
You can identify a remote peer with:
* IPv4 or IPv6 address. This mode is easiest for configuration and mostly used when a peer has a public static IP address;
* Hostname. This mode is similar to IP address, only you define DNS name instead of an IP. Could be used when a peer has a public IP address and DNS name, but an IP address could be changed from time to time;
* Remote ID of the peer. In this mode, there is no predefined remote address nor DNS name of the peer. This mode is useful when a peer doesn't have a publicly available IP address (NAT between it and VyOS), or IP address could be changed.
Each site-to-site peer has the next options:
* ``authentication`` - configure authentication between VyOS and a remote peer. Suboptions:
* ``id`` - ID for the local VyOS router. If defined, during the authentication it will be send to remote peer;
* ``mode`` - mode for authentication between VyOS and remote peer:
* ``pre-shared-secret`` - use predefined shared secret phrase, must be the same for local and remote side;
* ``rsa`` - use simple shared RSA key. The key must be defined in the ``set vpn rsa-keys`` section;
* ``x509`` - use certificates infrastructure for authentication.
* ``pre-shared-secret`` - predefined shared secret. Used if configured ``mode pre-shared-secret``;
* ``remote-id`` - define an ID for remote peer, instead of using peer name or address. Useful in case if the remote peer is behind NAT or if ``mode x509`` is used;
* ``rsa-key-name`` - shared RSA key for authentication. The key must be defined in the ``set vpn rsa-keys`` section;
* ``use-x509-id`` - use local ID from x509 certificate. Cannot be used when ``id`` is defined;
* ``x509`` - options for x509 authentication mode:
* ``ca-cert-file`` - CA certificate file. Using for authenticating remote peer;
* ``cert-file`` - certificate file, which will be used for authenticating local router on remote peer;
* ``crl-file`` - file with the Certificate Revocation List. Using to check if a certificate for the remote peer is valid or revoked;
* ``key`` - a private key, which will be used for authenticating local router on remote peer:
* ``file`` - path to the key file;
* ``password`` - passphrase private key, if needed.
* ``connection-type`` - how to handle this connection process. Possible variants:
* ``initiate`` - do initial connection to remote peer immediately after configuring and after boot. In this mode the connection will not be restarted in case of disconnection, therefore should be used only together with DPD or another session tracking methods;
* ``respond`` - do not try to initiate a connection to a remote peer. In this mode, the IPSec session will be established only after initiation from a remote peer. Could be useful when there is no direct connectivity to the peer due to firewall or NAT in the middle of the local and remote side.
* ``default-esp-group`` - ESP group to use by default for traffic encryption. Might be overwritten by individual settings for tunnel or VTI interface binding;
* ``description`` - description for this peer;
* ``dhcp-interface`` - use an IP address, received from DHCP for IPSec connection with this peer, instead of ``local-address``;
* ``force-encapsulation`` - force encapsulation of ESP into UDP datagrams. Useful in case if between local and remote side is firewall or NAT, which not allows passing plain ESP packets between them;
* ``ike-group`` - IKE group to use for key exchanges;
* ``ikev2-reauth`` - reauthenticate remote peer during the rekeying process. Can be used only with IKEv2:
* ``yes`` - create a new IKE_SA from the scratch and try to recreate all IPsec SAs;
* ``no`` - rekey without uninstalling the IPsec SAs;
* ``inherit`` - use default behavior for the used IKE group.
* ``local-address`` - local IP address for IPSec connection with this peer. If defined ``any``, then an IP address which configured on interface with default route will be used;
* ``tunnel`` - define criteria for traffic to be matched for encrypting and send it to a peer:
* ``disable`` - disable this tunnel;
* ``esp-group`` - define ESP group for encrypt traffic, defined by this tunnel;
* ``local`` - define a local source for match traffic, which should be encrypted and send to this peer:
* ``port`` - define port. Have effect only when used together with ``prefix``;
* ``prefix`` - IP network at local side.
* ``protocol`` - define the protocol for match traffic, which should be encrypted and send to this peer;
* ``remote`` - define the remote destination for match traffic, which should be encrypted and send to this peer:
* ``port`` - define port. Have effect only when used together with ``prefix``;
* ``prefix`` - IP network at remote side.
* ``vti`` - use a VTI interface for traffic encryption. Any traffic, which will be send to VTI interface will be encrypted and send to this peer. Using VTI makes IPSec configuration much flexible and easier in complex situation, and allows to dynamically add/delete remote networks, reachable via a peer, as in this mode router don't need to create additional SA/policy for each remote network:
* ``bind`` - select a VTI interface to bind to this peer;
* ``esp-group`` - define ESP group for encrypt traffic, passed this VTI interface.
Examples:
------------------
IKEv1
^^^^^
Example:
* WAN interface on `eth1`
* left subnet: `192.168.0.0/24` site1, server side (i.e. locality, actually
there is no client or server roles)
* left local_ip: `198.51.100.3` # server side WAN IP
* right subnet: `10.0.0.0/24` site2,remote office side
* right local_ip: `203.0.113.2` # remote office side WAN IP
.. code-block:: sh
# server config
set vpn ipsec esp-group office-srv-esp compression 'disable'
set vpn ipsec esp-group office-srv-esp lifetime '1800'
set vpn ipsec esp-group office-srv-esp mode 'tunnel'
set vpn ipsec esp-group office-srv-esp pfs 'enable'
set vpn ipsec esp-group office-srv-esp proposal 1 encryption 'aes256'
set vpn ipsec esp-group office-srv-esp proposal 1 hash 'sha1'
set vpn ipsec ike-group office-srv-ike ikev2-reauth 'no'
set vpn ipsec ike-group office-srv-ike key-exchange 'ikev1'
set vpn ipsec ike-group office-srv-ike lifetime '3600'
set vpn ipsec ike-group office-srv-ike proposal 1 encryption 'aes256'
set vpn ipsec ike-group office-srv-ike proposal 1 hash 'sha1'
set vpn ipsec ipsec-interfaces interface 'eth1'
set vpn ipsec site-to-site peer 203.0.113.2 authentication mode 'pre-shared-secret'
set vpn ipsec site-to-site peer 203.0.113.2 authentication pre-shared-secret 'SomePreSharedKey'
set vpn ipsec site-to-site peer 203.0.113.2 ike-group 'office-srv-ike'
set vpn ipsec site-to-site peer 203.0.113.2 local-address '198.51.100.3'
set vpn ipsec site-to-site peer 203.0.113.2 tunnel 0 allow-nat-networks 'disable'
set vpn ipsec site-to-site peer 203.0.113.2 tunnel 0 allow-public-networks 'disable'
set vpn ipsec site-to-site peer 203.0.113.2 tunnel 0 esp-group 'office-srv-esp'
set vpn ipsec site-to-site peer 203.0.113.2 tunnel 0 local prefix '192.168.0.0/24'
set vpn ipsec site-to-site peer 203.0.113.2 tunnel 0 remote prefix '10.0.0.0/21'
# remote office config
set vpn ipsec esp-group office-srv-esp compression 'disable'
set vpn ipsec esp-group office-srv-esp lifetime '1800'
set vpn ipsec esp-group office-srv-esp mode 'tunnel'
set vpn ipsec esp-group office-srv-esp pfs 'enable'
set vpn ipsec esp-group office-srv-esp proposal 1 encryption 'aes256'
set vpn ipsec esp-group office-srv-esp proposal 1 hash 'sha1'
set vpn ipsec ike-group office-srv-ike ikev2-reauth 'no'
set vpn ipsec ike-group office-srv-ike key-exchange 'ikev1'
set vpn ipsec ike-group office-srv-ike lifetime '3600'
set vpn ipsec ike-group office-srv-ike proposal 1 encryption 'aes256'
set vpn ipsec ike-group office-srv-ike proposal 1 hash 'sha1'
set vpn ipsec ipsec-interfaces interface 'eth1'
set vpn ipsec site-to-site peer 198.51.100.3 authentication mode 'pre-shared-secret'
set vpn ipsec site-to-site peer 198.51.100.3 authentication pre-shared-secret 'SomePreSharedKey'
set vpn ipsec site-to-site peer 198.51.100.3 ike-group 'office-srv-ike'
set vpn ipsec site-to-site peer 198.51.100.3 local-address '203.0.113.2'
set vpn ipsec site-to-site peer 198.51.100.3 tunnel 0 allow-nat-networks 'disable'
set vpn ipsec site-to-site peer 198.51.100.3 tunnel 0 allow-public-networks 'disable'
set vpn ipsec site-to-site peer 198.51.100.3 tunnel 0 esp-group 'office-srv-esp'
set vpn ipsec site-to-site peer 198.51.100.3 tunnel 0 local prefix '10.0.0.0/21'
set vpn ipsec site-to-site peer 198.51.100.3 tunnel 0 remote prefix '192.168.0.0/24'
Show status of new setup:
.. code-block:: sh
vyos@srv-gw0:~$ show vpn ike sa
Peer ID / IP Local ID / IP
------------ -------------
203.0.113.2 198.51.100.3
State Encrypt Hash D-H Grp NAT-T A-Time L-Time
----- ------- ---- ------- ----- ------ ------
up aes256 sha1 5 no 734 3600
vyos@srv-gw0:~$ show vpn ipsec sa
Peer ID / IP Local ID / IP
------------ -------------
203.0.113.2 198.51.100.3
Tunnel State Bytes Out/In Encrypt Hash NAT-T A-Time L-Time Proto
------ ----- ------------- ------- ---- ----- ------ ------ -----
0 up 7.5M/230.6K aes256 sha1 no 567 1800 all
If there is SNAT rules on eth1, need to add exclude rule
.. code-block:: sh
# server side
set nat source rule 10 destination address '10.0.0.0/24'
set nat source rule 10 'exclude'
set nat source rule 10 outbound-interface 'eth1'
set nat source rule 10 source address '192.168.0.0/24'
# remote office side
set nat source rule 10 destination address '192.168.0.0/24'
set nat source rule 10 'exclude'
set nat source rule 10 outbound-interface 'eth1'
set nat source rule 10 source address '10.0.0.0/24'
To allow traffic to pass through to clients, you need to add the following
rules. (if you used the default configuration at the top of this page)
.. code-block:: sh
# server side
set firewall name OUTSIDE-LOCAL rule 32 action 'accept'
set firewall name OUTSIDE-LOCAL rule 32 source address '10.0.0.0/24'
# remote office side
set firewall name OUTSIDE-LOCAL rule 32 action 'accept'
set firewall name OUTSIDE-LOCAL rule 32 source address '192.168.0.0/24'
IKEv2
^^^^^
Imagine the following topology
.. figure:: ../_static/images/vpn_s2s_ikev2.png
:scale: 50 %
:alt: IPSec IKEv2 site2site VPN
IPSec IKEv2 site2site VPN (source ./draw.io/vpn_s2s_ikev2.drawio)
.. note:: Don't get confused about the used /31 tunnel subnet. RFC3031_ gives
you additional information for using /31 subnets on point-to-point links.
**left**
.. code-block:: sh
set interfaces vti vti10 address '10.0.0.2/31'
set vpn ipsec esp-group ESP_DEFAULT compression 'disable'
set vpn ipsec esp-group ESP_DEFAULT lifetime '3600'
set vpn ipsec esp-group ESP_DEFAULT mode 'tunnel'
set vpn ipsec esp-group ESP_DEFAULT pfs 'dh-group19'
set vpn ipsec esp-group ESP_DEFAULT proposal 10 encryption 'aes256gcm128'
set vpn ipsec esp-group ESP_DEFAULT proposal 10 hash 'sha256'
set vpn ipsec ike-group IKEv2_DEFAULT dead-peer-detection action 'hold'
set vpn ipsec ike-group IKEv2_DEFAULT dead-peer-detection interval '30'
set vpn ipsec ike-group IKEv2_DEFAULT dead-peer-detection timeout '120'
set vpn ipsec ike-group IKEv2_DEFAULT ikev2-reauth 'no'
set vpn ipsec ike-group IKEv2_DEFAULT key-exchange 'ikev2'
set vpn ipsec ike-group IKEv2_DEFAULT lifetime '10800'
set vpn ipsec ike-group IKEv2_DEFAULT mobike 'disable'
set vpn ipsec ike-group IKEv2_DEFAULT proposal 10 dh-group '19'
set vpn ipsec ike-group IKEv2_DEFAULT proposal 10 encryption 'aes256gcm128'
set vpn ipsec ike-group IKEv2_DEFAULT proposal 10 hash 'sha256'
set vpn ipsec ipsec-interfaces interface 'eth0.201'
set vpn ipsec site-to-site peer 172.18.202.10 authentication id '172.18.201.10'
set vpn ipsec site-to-site peer 172.18.202.10 authentication mode 'pre-shared-secret'
set vpn ipsec site-to-site peer 172.18.202.10 authentication pre-shared-secret 'secretkey'
set vpn ipsec site-to-site peer 172.18.202.10 authentication remote-id '172.18.202.10'
set vpn ipsec site-to-site peer 172.18.202.10 connection-type 'initiate'
set vpn ipsec site-to-site peer 172.18.202.10 ike-group 'IKEv2_DEFAULT'
set vpn ipsec site-to-site peer 172.18.202.10 ikev2-reauth 'inherit'
set vpn ipsec site-to-site peer 172.18.202.10 local-address '172.18.201.10'
set vpn ipsec site-to-site peer 172.18.202.10 vti bind 'vti10'
set vpn ipsec site-to-site peer 172.18.202.10 vti esp-group 'ESP_DEFAULT'
**right**
.. code-block:: sh
set interfaces vti vti10 address '10.0.0.3/31'
set vpn ipsec esp-group ESP_DEFAULT compression 'disable'
set vpn ipsec esp-group ESP_DEFAULT lifetime '3600'
set vpn ipsec esp-group ESP_DEFAULT mode 'tunnel'
set vpn ipsec esp-group ESP_DEFAULT pfs 'dh-group19'
set vpn ipsec esp-group ESP_DEFAULT proposal 10 encryption 'aes256gcm128'
set vpn ipsec esp-group ESP_DEFAULT proposal 10 hash 'sha256'
set vpn ipsec ike-group IKEv2_DEFAULT dead-peer-detection action 'hold'
set vpn ipsec ike-group IKEv2_DEFAULT dead-peer-detection interval '30'
set vpn ipsec ike-group IKEv2_DEFAULT dead-peer-detection timeout '120'
set vpn ipsec ike-group IKEv2_DEFAULT ikev2-reauth 'no'
set vpn ipsec ike-group IKEv2_DEFAULT key-exchange 'ikev2'
set vpn ipsec ike-group IKEv2_DEFAULT lifetime '10800'
set vpn ipsec ike-group IKEv2_DEFAULT mobike 'disable'
set vpn ipsec ike-group IKEv2_DEFAULT proposal 10 dh-group '19'
set vpn ipsec ike-group IKEv2_DEFAULT proposal 10 encryption 'aes256gcm128'
set vpn ipsec ike-group IKEv2_DEFAULT proposal 10 hash 'sha256'
set vpn ipsec ipsec-interfaces interface 'eth0.202'
set vpn ipsec site-to-site peer 172.18.201.10 authentication id '172.18.202.10'
set vpn ipsec site-to-site peer 172.18.201.10 authentication mode 'pre-shared-secret'
set vpn ipsec site-to-site peer 172.18.201.10 authentication pre-shared-secret 'secretkey'
set vpn ipsec site-to-site peer 172.18.201.10 authentication remote-id '172.18.201.10'
set vpn ipsec site-to-site peer 172.18.201.10 connection-type 'initiate'
set vpn ipsec site-to-site peer 172.18.201.10 ike-group 'IKEv2_DEFAULT'
set vpn ipsec site-to-site peer 172.18.201.10 ikev2-reauth 'inherit'
set vpn ipsec site-to-site peer 172.18.201.10 local-address '172.18.202.10'
set vpn ipsec site-to-site peer 172.18.201.10 vti bind 'vti10'
set vpn ipsec site-to-site peer 172.18.201.10 vti esp-group 'ESP_DEFAULT'
.. _RFC3031: https://tools.ietf.org/html/rfc3021
|
